DOWNLOAD Sharp AR-M35 / AR-M450 (serv.man40) Service Manual ↓ Size: 2.37 MB | Pages: 58 in PDF or view online for FREE

Document Systems Support

15

Perform Sim.22-06 Simulation Data Print

Perform Sim. 24-04  Maintenance Counter Reset

Perform Sim.21-01  Maintenance Cycle Check

Perform Sim.  24-05  Dev Counter Reset

Perform Sim.  25-02  Developer Level Setting

Perform Sim.  24-07  Drum Membrane Counter Reset

Perform Sim. 46-02 Copy Quality Adjustment (Copy Mode)

Perform Sim.22-06  Simulation Data Print

Document Systems Support

16

1

Developer doctor gap

.45mm

2

MG roller main pole position

54.2

3

Dev bias voltage

Sim 8-1

4

Main charger grid voltage

Sim 8-2

5

Transfer charge voltage

Sim 8-6

8

Toner concentration

Sim 25-2

1

Horizontal image distortion

LSU lever adjustment

2

Print off centre

Sim 50-10

3

Laser power setting

Sim 61-20

1

Vertical image distortion balance

Copy lamp unit installing
position

2

Vertical image distortion balance

No2/3 mirror base
installing position

3

Vertical image distortion

Winding pulley position

4

Horizontal image distortion

F rail height adjust

5

Main scan magnification ratio

CCD unit position

6

Main scan magnification ratio

Sim 48-1

7

Shading plate correction

Sim 46-17

8

Scanning image position

Sim 50-2

9

Original off center

Sim 50-12

1

Copy mode

Sim 46

1

Manual bypass detection level

Sim 40-2

2

Paper size setting

1

Separation Pawl Timing

Sim 51-1

2

Resist Roller Buckle

Sim 51-2

1
2
3

Original size sensor detection level
Touch panel
Key touch sound volume

Sim 41-1 / 41-2
Sim 65-1
Sound volume adjustment

1
2

Hinge height
Open/Close sensor position

Table clearance
Sim 2-2

Document Systems Support

17

Simulation codes allow the copier engineer to test certain operations of the machine, and
also allow access to counter information and other operational variables. It is implemented to
assist the engineer in support of the product and it is important, therefore, that this mode of
operation is not be disclosed to users.

The key sequence required to enter the copier simulation mode is as follows :

Once in simulation mode, a ‘main’ code and a ‘sub’ code relating to the required operation
must be entered :

The operation of simulations in “Tiger” models is very similar to those utilized in “Cougar”.
There are differences so READ THE ON SCREEN INSTRUCTIONS CAREFULLY

Document Systems Support

18

Default
Setting

1

--

Checks optical system.

01

Scanner test

02

Scanner sensor check

2

--

Checks Document Feeder ageing.

01

DF ageing test.

02

DF sensor check

03

DF output check (motor, clutch, solenoid)

3

--

Checks Finisher activation.

02

Finisher sensor check

03

Finisher output check (motor, clutch, solenoid)

06

Finisher jogger adjustment

10

Console Finisher adjustment (AR-FN7)

20

Mail bin stacker sensor check

21

Mail bin stacker load test

4

--

Checks Desk/LCT activation

02

Desk/LCT sensor check

03

Desk/LCT o/put check (motor, clutch, solenoid)

5

--

Checks the lighting of lamps.

01

LCD/LED test

02

Heater lamp check

03

Copy lamp check

6

--

Checks paper feed component activation

01

Paper feed o/put check (motor clutch solenoid)

02

Fan motor activation

7

--

Checks paper feed ageing

01

Paper feed ageing test setting

06

Interval ageing cycle timer set up

08

Warm up time display setting

8

--

Checks process voltages output.

01

Developer bias setting and output

02

MHV/Grid setting and output

06

THV check and adjust ( transfer).

17

THV setting and output

9

--

Checks ADU activation.

01

ADU output check (motor, clutch, solenoid)

02

ADU sensor check