Sharp AR-M256 (serv.man11) Service Manual ▷ View online
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 7
Operation/procedure
Select the load to be checked with the 10-key, and press the [START] key.
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
(20 times)
(20 times)
Note: Executable only when the RSPF is installed.
Operation/procedure
Used to display the operations of sensors and detectors in the finisher
section.
section.
The active sensors and detectors are highlighted.
When AR-FN5A is installed
When AR-F14N is installed
When AR-F14N/Punch unit is installed
Note: Executable only when the finisher is installed.
Operation/procedure
Select the load to be checked with the 10-key, and press the [START] key.
The finisher main motor operates for 10sec, the staple motor 5 times,
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
the tray lift-up motor one reciprocating operation, other motors max. 20
reciprocating operations from the home position, the solenoid repeats
500msec ON and 500msec OFF 20 times.
The staple operation motor operates only when there is no cartridge
installed.
installed.
When AR-FN5A is installed
2-3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the RSPF
unit and the control circuits.
unit and the control circuits.
Section
RSPF
Item
Operation
Item
Content
1
DTM-F
RSPF motor forward rotation
2
DTM-R
RSPF motor reverse rotation
3
DFCL
RSPF paper feed clutch
4
CLH
RSPF PS clutch
5
GSOL
Document exit gate solenoid
6
RSOL
Document exit pressure solenoid
3
3-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and detector in
the finisher and the related circuit.
the finisher and the related circuit.
Section
Finisher
Item
Operation
INPD
Finisher paper entry sensor
FWPS
Paper width sensor
JGHP1
Side guide plate HP sensor
JGHP2
Rear edge plate HP sensor
JGPD
Tray paper empty sensor
T1OD
1st tray exit sensor
T1PF
1st tray paper full sensor
PGOP
JAM processing PG open/close detection sensor
T2OD
2nd tray exit sensor
OFHP
Offset HP sensor
T2UP
Tray position sensor (upper)
T2DN
Tray position sensor (lower)
JGDSW
Tray jam processing interlock
EVRE
Lift-up drive control sensor
STHP
Staple HP sensor
READY
Self priming sensor
LSTS
Staple empty sensor
NCTS
Cartridge empty sensor
STND
Staple supply cover open/close sensor
T2PUD
2nd tray upper surface sensor
FSSS
Stapler safety switch
FJS
Joint switch
FFDSW
Front door switch
FTCS
Upper cover sensor
FFDS
Front door sensor
FSPS
Self prime sensor
FSUC
Stapler connection detection
FSS
Stapler sensor
FSTHPS
Stapler HP sensor
FSHPS
Slide HP sensor
FLE
Lift lock sensor
FLLLS
Lift lower limit sensor
FULS
Lift upper limit sensor
FFE
Book making clock sensor
FFES
Book making paper sensor
FFRHPS
Book making roller HP sensor
FFHPS
Book making HP sensor
FFPS
Book making position sensor
FSLS
Paper surface sensor
FBES
Tray paper sensor
FPE
Punch motor encoder
FPSHPS
Punch side resist home position
FPUC
Punch connection detection
FPDS
Punch dust sensor
FPDSS4
Punch side resist sensor 4
FPDSS3
Punch side resist sensor 3
FPDSS2
Punch side resist sensor 2
FPDSS1
Punch side resist sensor 1
FPTS
Punch timing sensor
3-3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the load in the finisher
and the control circuit.
and the control circuit.
Section
Finisher
Item
Operation
Item
Content
1
JGM1
Side guide plate drive motor
2
JGM2
Rear edge plate drive motor
3
FM-600
Finisher main motor (600dpi)
4
FM-1200
Finisher main motor (1200dpi)
5
EVM
Tray lift-up motor
6
OFM
Tray offset motor
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 8
When AR-F14N is installed
Note: Executable only when the finisher is installed.
Operation/procedure
After the paper size is set, the side guide plate and the rear guide plate
are set.
are set.
1.
Enter the desired item with the 10-key, and press the [START] key.
2.
Enter the adjustment value with the 10-key, and press the [START]
key.
key.
There are 6 adjustment values for the side guide plate, and 12 for the
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
rear guide plate. The adjustment position is determined from the table
below according to the paper size.
Note: Executable only when the finisher is installed.
Operation/procedure
1.
Touch the operation item to be set.
2.
Enter the set value with the 10-key.
7
STM
Staple operation motor
8
OGSLR
Transport selection gate solenoid (R)
9
OGSLL
Transport selection gate solenoid (L)
10
JGSL1
Rear edge plate drive solenoid
11
JGSL2
Upper alignment plate drive solenoid
12
SHTSL
Shutter drive solenoid
13
T2SCL
Paper exit roller clutch
14
STGSL
Paper holding solenoid
Item
Content
1
FFC
Folding clutch
2
FPSM
Punch side resist motor (Execution is possible only
when the punch unit is installed.)
when the punch unit is installed.)
3
FPNM
Punch motor (Execution is possible only when the
punch unit is installed.)
punch unit is installed.)
4
FLM
Shift motor
5
FFSM
Stapler motor
6
FSM
Slide motor
7
FRJM
Alignment motor R
8
FFJM
Alignment motor F
9
FAM
Bundle exit motor
10
FPM
Paddle motor
11
FFM
Transport motor
12
FJM
Interface transport motor
3-6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the alignment position (side regulation
plate, rear edge regulation plate) for each paper size.
Shifts to the specified paper size position.
plate, rear edge regulation plate) for each paper size.
Shifts to the specified paper size position.
Section
Finisher
Item
Operation
Item
Content
Setting
range
Default
1
PAPER SIZE
Paper size
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT,
8:LG, 9:FC, 10:LTR,
11:8K, 12:16K)
(1:A3, 2:A4, 3:B4, 4:B5,
5:A4R, 6:WLT, 7:LT,
8:LG, 9:FC, 10:LTR,
11:8K, 12:16K)
1-12
A4
2
JOGGER POS X
Side guide plate
1-99
50
3
JOGGER POS Y
Rear edge guide plate
Item
Content
Paper size
Side guide plate
adjustment value number
Adjustment value number
of the rear edge guide
plate
A3
1
2
A4
1
9
B4
3
3
B5
3
10
A4R
5
6
WLT
2
1
LT
2
8
LG
4
4
FC
4
5
LTR
4
7
8K
6
11
16K
6
12
3-7
Purpose
Adjustment
Function (Purpose)
Used to adjust the offset tray operations.
Section
Finisher
Item
Operation
Item
Content
Installation
range
Default
1
PAPER PUSH
TMG
TMG
Paper holder
descending timing
in non-staple
descending timing
in non-staple
34-66
50
Used to adjust the descending timing of
the paper holder lever before lift-up
operation after paper exit or offset
operation. (The paper holder lever
prevents against paper shift in paper top
surface detection and paper stacking.)
the paper holder lever before lift-up
operation after paper exit or offset
operation. (The paper holder lever
prevents against paper shift in paper top
surface detection and paper stacking.)
2
PAPER OUT
DOWN
DOWN
Tray descending
distance after non-
staple paper exit
distance after non-
staple paper exit
0-12
1
Used to adjust the offset tray descending
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
distance after non-staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
3
STAPLE UP
Tray lift distance
before staple paper
exit
before staple paper
exit
0-12
6
The height of the tray standby position in
stapling is changed for that in non-stapling
to improve stacking capacity in stapling.
(The relative distance for the height of the
tray standby position in non-stapling is
set.)
stapling is changed for that in non-stapling
to improve stacking capacity in stapling.
(The relative distance for the height of the
tray standby position in non-stapling is
set.)
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 9
Note:Executable only when the finisher is installed.
Operation/procedure
1.
Select an item to be adjusted with 10-key, and press [START] key.
2.
Enter an adjustment value with 10-key, and press [START] key.
* For 9 and 10, execution is possible only when the punch unit is
installed.
Operation/procedure
Select item “1,” and press the [START] key.
The shifter is reciprocated continuously at the specified interval.
[Selection 2]
1.
Select item “2,” and press the [START] key.
2.
Move the shifter to the home position or in one way by the specified
steps with the following keys.
steps with the following keys.
4
STAPLE DOWN
Tray descending
distance after staple
paper exit
distance after staple
paper exit
0-12
6
Used to adjust the offset tray descending
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
distance after staple paper exit.
The descending distance is the relative
distance from the non-staple standby
position.
5
OFFSET INI.POS
Offset tray shift
position adjustment
position adjustment
0-99
13
Used to shift the offset tray to the shipment
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
position or the disassembly position.
The offset tray is shifted to the specified
counter position.
(In the case of 0-94 (Shipment position)
1) Initialize the offset tray normally.
2) The tray descends to the parameter
position + 1 pulse position.
3) The tray lifts up to the specified param-
eter position.
(Disassembly position: 94-99)
1) The tray descends to the bottom.
* If there is some paper in the offset tray,
the tray cannot descend to the specified
position. Check to insure that there is no
paper in the tray before execution.
position. Check to insure that there is no
paper in the tray before execution.
3-10
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to make each adjustment of the saddle finisher.
Item
Operation
Item
Content
Installation
range
Default
1
SADDLE
POSITION
POSITION
Saddle stitch
position adjustment
position adjustment
0-400
200
2
FOLDING
POSITION
POSITION
Saddle folding
position adjustment
position adjustment
0-400
200
3
FRONT ADJUST
Front alignment
position adjustment
position adjustment
0-20
10
4
REAR ADJUST
Rear alignment
position adjustment
position adjustment
0-20
10
5
STAPLE REAR
Staple rear one-
position binding
position adjustment
position binding
position adjustment
0-200
100
6
STAPLE FRONT
Staple front one-
position binding
position adjustment
position binding
position adjustment
0-200
100
Item
Content
Installation
range
Default
7
STAPLE BOTH
Staple two-position
binding center
adjustment
binding center
adjustment
0-200
100
8
STAPLE PITCH
Staple two-position
binding pitch
adjustment
binding pitch
adjustment
0-100
50
9
PUNCH CENTER
Punch center
adjustment
adjustment
47-53
50
10 PUNCH HOLE
Punch hole position
adjustment
adjustment
0-100
50
3-11
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the shifter operation.
Reciprocating operations are continuously performed
or the home position is checked.
(The shifter is shifted to the home position or moved in
one way by the specified steps.)
Reciprocating operations are continuously performed
or the home position is checked.
(The shifter is shifted to the home position or moved in
one way by the specified steps.)
Item
Operation
Item
Content
1
F-R
Reciprocating operation
2
HP CHECK
Home position check
[*] key
Shifts the position toward R side by the specified steps.
[0 key
Shifts the position toward HP side by the specified steps.
[#] key
Shifts to F.
SFTHP
Shifter home position (At detection, highlighted)
Item
Content
Installation
range
Default
SIMULATION 3-10
AR-M256/M257/M258/M316/M317/M318/5625/5631 SIMULATION 8 - 10
Operation/procedure
The operating states of the sensor and the detector are displayed.
(Only the installed option cassettes are displayed. For the standard
tray, use SIM 30-2.)
(Only the installed option cassettes are displayed. For the standard
tray, use SIM 30-2.)
The active sensors and detectors are highlighted.
Note: Execution is possible only when the option cassette is installed.
Operation/procedure
Select the load to be checked with the 10-key, and press the [START] key.
The motor for 10sec, the solenoid ON for 500msec, OFF for 500msec.
The lift-up motor operates only when the tray is opened. (20 times)
Note: Execution is possible only when the option cassette is installed.
Operation/procedure
The LCD is displayed as follows. (All LED’s are ON.)
With the upper half highlighted and the lower half normally displayed,
contrast changes “Standard
contrast changes “Standard
→
MAX
→
MIN.” in every 2sec.
(6 sec later)
With the upper half normally displayed and the lower half highlighted,
contrast changes “Standard
contrast changes “Standard
→
MAX
→
MIN.” in every 2sec.
* When returning to the sub menu selection menu, the display of the
standard contrast is displayed for an instant.
Operation/procedure
1.
Select the lamp to be checked with the 10-key, and press the
[START] key.
[START] key.
ON/OFF operation of the heater lamp is repeated 5 times in an interval
of 100ms/900ms.
When completing the operation, the cooling fan is rotated at a low speed.
of 100ms/900ms.
When completing the operation, the cooling fan is rotated at a low speed.
Item Content
4
4-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensor and detector in
the option cassette and the related circuit.
the option cassette and the related circuit.
Section
Paper feed
Item
Operation
PED2
2nd cassette paper empty sensor
LUD2
2nd cassette paper upper limit detection sensor
PFD2
2nd cassette paper pass sensor
CD2
2nd cassette empty sensor
PED3
3rd cassette paper empty sensor
LUD3
3rd cassette paper upper limit detection sensor
PFD3
3rd cassette paper pass sensor
CD3
3rd cassette empty sensor
PED4
4th cassette paper empty sensor
LUD4
4th cassette paper upper limit detection sensor
PFD4
4th cassette paper pass sensor
CD4
4th cassette empty sensor
DSWR2
2nd cassette right door detection sensor
DSWR3
3rd cassette right door detection sensor
DSWR4
4th cassette right door detection sensor
4-3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the load in the option
tray and the control circuit.
tray and the control circuit.
Section
Paper feed
Item
Operation
Item
Content
1
LUM2
2nd cassette lift-up motor
2
CPFC2
2nd cassette pick-up solenoid
3
CPFS2
2nd cassette paper feed clutch
4
TRC2
2nd cassette transport roller clutch
5
DM
2nd cassette paper transport motor
(3rd cassette paper transport motor)
(3rd cassette paper transport motor)
6
LUM3
3rd cassette lift-up motor
7
CPFC3
3rd cassette pick-up solenoid
8
CPFS3
3rd cassette paper feed clutch
9
TRC3
3rd cassette transport roller clutch
10
LUM4
4th cassette lift-up motor
11
CPFC4
4th cassette pick-up solenoid
12
CPFS4
4th cassette paper feed clutch
5
5-1
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the display (LED), LCD
in the operation panel, and control circuit.
in the operation panel, and control circuit.
Section
Operation (screen/operation)
Item
Operation
5-2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the heater lamp and the
control circuit.
control circuit.
Section
Fusing
Item
Operation
Item
Content
1
HL1
Heater lamp 1 (Main) operation
2
HL2
Heater lamp 2 (Sub) operation
Click on the first or last page to see other AR-M256 (serv.man11) service manuals if exist.