Sharp AR-M205 (serv.man15) Service Manual ▷ View online
AR-M205 DISASSEMBLY AND ASSEMBLY 11-5
Assembly: Put the fusing harness (A) on the heater lamp (B) as shown
in the figure and fix them together.<R>Place the fusing
harness inside the rib (C).
harness inside the rib (C).
E.Upper heat roller
Disassembly:
There are three pawls on the fusing cover. Remove the
screws and slide the fusing cover to the right to remove.
The heater lamp is fixed on the fusing cover with a
screw. Slide the fusing cover to the front and remove the
screw. Slide the fusing cover to the front and remove the
screw, then remove the heater lamp.
F.Separation pawl
(A)
(B)
(C)
(1)
(3)
(4)
(2)
(2)
(1)
(3)
(1)
(2)
(1)
(1)
(2)
Grease(JFE552)
Floil(GU2)
(2)
(2)
(1)
(3)
(3)
(2)
(2)
(3)
(3)
(1)
& !"
AR-M205 DISASSEMBLY AND ASSEMBLY 11-6
G.Lower heat roller
Assembly:
When installing the paper guide (3) before fusing, fix the
paper guide fixing plate with screws temporarily so that the
paper guide fixing plate (2) is in contact with the frame
bottom under fusing (A). Set the paper guide (3) before
bottom under fusing (A). Set the paper guide (3) before
fusing to the bottom line of the positioning reference (B),
and tighten the screw firmly.
H.Separation pawl
4.Paper exit section
A.Ozone filter
B.Cooling fan
(1)
(1)
(3)
(2)
(2)
(A)
(4)
(B)
(B)
Grease(JFE552)
No.
Content
A
Ozone filter
B
Cooling fan
C
Paper exit unit
D
Paper exit sensor / duplex sensor
E
Transport roller
F
Paper exit roller
G
Paper exit interface P.W.B.
(1)
(1)
(2)
(1)
(1)
(1)
(1)
(2)
(2)
(1)
(2)
(2)
(2)
(3)
(3)
(2)
(1)
' !"
AR-M205 DISASSEMBLY AND ASSEMBLY 11-7
C.Paper exit unit
D.Paper exit sensor / duplex sensor
(A)Exit sensor
(B)Duplex sensor
E.Transport roller
(2)
(4)
(2)
(2)
(2)
(1)
(3)
(1)
(2)
(3)
(3)
(1)
(3)
(2)
(5)
(5)
(1)
(1)
(3)
(2)
(1)
(4)
(4)
(6)
(A)
(B)
(1)
(2)
(1)
(1)
(2)
(3)
(4)
(5)
(3)
( !"
AR-M205 DISASSEMBLY AND ASSEMBLY 11-8
F.Paper exit roller
Assembly:
Insert the spring pin so that the waveform (A) of the spring
pin faces in the longitudinal direction of the paper exit
drive gear long hole (B).<R>Be sure to insert two ribs (C)
into the groove (D).
into the groove (D).
G.Paper exit interface P.W.B.
5.MCU
A.MCU disassembly
Note: When replacing the MCU PWB, be sure to replace the EEPROM of
the MCU PWB to be replaced.
Note: When replacing the MCU PWB, be sure to restore the original
jumper conditions.
6.Optical frame unit
A.Optical frame unit
Installation:
Install the optical unit in the sequence shown above.
(1)
(1)
(2)
(A)
(B)
(D)
(C)
(C)
(1)
(1)
(2)
(2)
(3)
(1)
(1)
(2)
(2)
(3)
(1)
(2)
(2)
(3)
No.
Content
A
MCU disassembly
No.
Content
A
Optical frame unit
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(1)
(2)
(2)
(2)
(3)
(1)
(1)
(1)
(1)
(1)
(1)
(2)
(1)
(1)
) !"
Click on the first or last page to see other AR-M205 (serv.man15) service manuals if exist.