Sharp AR-FX12 (serv.man7) Service Manual ▷ View online
AR-FX12 MACHINE OPERATION 7-5
U2
00
Content
EEPROM read/write error (ICU).
Details
Write error to EEPROM.
Cause
EEPROM trouble.
Installation of EEPROM which is not
initialized.
ICU PWB EEPROM access circuit trouble.
Installation of EEPROM which is not
initialized.
ICU PWB EEPROM access circuit trouble.
Check &
Remedy
Remedy
Check that the EEPROM is properly set.
To save the counter data/adjustment values,
make notes of the counter/adjustment values
with the simulation.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
To save the counter data/adjustment values,
make notes of the counter/adjustment values
with the simulation.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
22
Content
SRAM memory check sum error (ICU).
Details
SRAM memory check sum error in the MFPC
section.
section.
Cause
SRAM trouble.
Hung up of the control circuit caused by
noises.
ICU PWB SRAM access circuit trouble.
Hung up of the control circuit caused by
noises.
ICU PWB SRAM access circuit trouble.
Check &
Remedy
Remedy
Initialize the communication management
table registered in the SRAM and the FAX
soft switches.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
table registered in the SRAM and the FAX
soft switches.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
23
Content
SRAM memory individual data check sum
error (ICU).
error (ICU).
Details
MFPC section SRAM memory individual
data check sum error (Communication
management table, sender registration data,
etc).
data check sum error (Communication
management table, sender registration data,
etc).
Cause
SRAM trouble.
Hung up of the control circuit caused by
noises.
ICU PWB SRAM access circuit trouble.
Hung up of the control circuit caused by
noises.
ICU PWB SRAM access circuit trouble.
Check &
Remedy
Remedy
Turn OFF/ON the power to automatically
initialize the data related to the contents
where a check sum error occurred.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
initialize the data related to the contents
where a check sum error occurred.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the ICU PWB.
50
Content
HD section individual data check sum error
(ICU).
(ICU).
Details
MFPC section HD individual data check sum
error (One-touch, group, program, etc).
error (One-touch, group, program, etc).
Cause
Write/read error from/to HD.
Hung up of the control circuit caused by
noises.
ICU PWB HD access circuit trouble.
Hung up of the control circuit caused by
noises.
ICU PWB HD access circuit trouble.
Check &
Remedy
Remedy
Turn OFF/ON the power to automatically
initialize the data related to the contents
where a check sum error occurred.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the HD PWB.
Replace the ICU PWB.
initialize the data related to the contents
where a check sum error occurred.
Registered contents are deleted. Register
the deleted contents again.
Cancel the U2 trouble with SIM16.
Replace the HD PWB.
Replace the ICU PWB.
MAIN
SUB
[07]MACHINEOPERATION.fm 5 ページ ２００４年１２月１５日 水曜日 午後２時２２分
AR-FX12 MACHINE OPERATION 7-6
B. Communication report codes
This code is indicated in the column of protocol communication report in a communication repot table and a communication management table when
communication is terminated.
<1>Communication report code XX (Top 2 digits): 00 ~ 99
<2>Communication report sub code 1: YY: Not used in this machine. (Always 00)
<3>Communication report sub code 2: ZZ: Indicates details of the report.
<3>Communication report sub code 2: ZZ: Indicates details of the report.
(1) Communication report code list 1
Means of communication: S = Send, R = Receive, P = Polling, B = Bulletin board
Report code
(Communication
result)
Display in the column of result
Content of communication interruption
Means of
communication
0 ~ 31
Refer to the following
descriptions.
descriptions.
Depends on the point of communication interruption. For 16 or later, V.34 mode
communication. Refer to "(2) Communication report code list 2" in 7-6.
communication. Refer to "(2) Communication report code list 2" in 7-6.
33
BUSY
The calling side cannot establish connection with the remote party.
34
CANCEL
A communication interruption command is made during sending/receiving.The
interruption key is pressed for interruption of input.
interruption key is pressed for interruption of input.
<S/R/P/B>
35
NG35XXXX
Power is failed during sending/receiving.
<S/R/P/B>
36
(No record paper)
37
(Record paper jam)
38
MEM. FULL
Memory over during reception.Print is not made during reception in acting
reception inhibit.
reception inhibit.
<R/P><R/P>
39
(Number of paper unmatched)
40
(Relay not received)
41
LENGTH OVER
The send data length of one page exceeds the limit (2m) in sending.
<S/B>
42
LENGTH OVER
The receive data length of one page exceeds the limit.
<R/P>
43
(Communication) (OK)
Speaking before data transmission
44
ORIGINAL ERROR
A document jam occurs in direct sending.
<S>
45
(Picture quality error)
46
NO RESPONSE
The FAX signal from the remote party is not detected within T1 time.
<S/P>
47
TX DECODE ERROR
A decode error occurs in the FAX board.
<S/B>
48
OK
Normal end of communication
Normal end of
communication
communication
OK REPLY RECEIVE
OK in internet FAX send with reception confirmation.
49
NO RX POLL
The called side does not have polling function in polling reception. The called side
has no data to send.
has no data to send.
<P><P>
50
RX POLL FAIL
In polling reception, DCN is received for DTC.In polling sending, there is no send
data.
data.
<P><B>
51
PASS # NG
In poling sending, the allow number is not matched. In polling sending, the
system number is not matched.
system number is not matched.
<B><B>
52
(No confidential function in
remote party)
remote party)
In confidential sending, the remote party does not have confidential function.
(Including other company's machines)
<1>The NSF signal has not "Confidential function" bit.
(Including other company's machines)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
53
(Confidential not received)
<1>In confidential sending, DCN is received for NSS.
<S>
54
(Confidential BOX NO NG)
<1>In confidential reception, a confidential box number which is not registered is
specified.
<R>
55
(No relay function in remote
party)
party)
In relay command sending, the remote machine has no relay function.
(Including other company's machine)
<1>The NSF signal has not "Confidential function" bit.
(Including other company's machine)
<1>The NSF signal has not "Confidential function" bit.
<2>The NSF is not a Sharp machine.
<S>
56
NO REL RX
<1>In relay command sending, DCN is received for NSS.
<2>In relay command reception, a remote station number which is not registered
is specified.
<3>In F code relay broadcasting, an F code relay command is received.
<S><R><R>
57
(Relay ID unmatched)
<1>In relay command reception, the relay ID does not match.
<R>
58
REJECTED
In reception, data are sent from a remote machine of receive inhibit number.
Communication report XX (YY ZZ)
[07]MACHINEOPERATION.fm 6 ページ ２００４年１２月１５日 水曜日 午後２時２２分
AR-FX12 MACHINE OPERATION 7-7
59
RX NO F-CODE POLL
In F code polling (calling), the remote machine has no DIS bit 47
(polling function).
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)
(polling function).
In F code polling (calling), the called side has no send data. (DIS bit 9 is 0.)
<P>
60
NO F-CODE POLL
In F code polling (calling), DCN is received for SEP. In bulletin board, there is no
send data for SEP.
send data for SEP.
<P><B>
61
RX POLL # NG
In bulletin board, the sub address (bulletin board number (SEP)) is not matched.
<B>
62
F POLL PASS # NG
In bulleting board, the pass code (PWD) is not matched.
<B>
63
NO F FUNC
In F code sending, the remote machine has no DIS bit 49 (sub address function).
Check that the remote machine conforms to F code.
Check that the remote machine conforms to F code.
<S>
64
NO F-CODE
In F code sending :
<1>DCN is received for SUB. --- Check the box number.
<2>DCN is received for SID. --- Check the box number and pass code.
In F code receiving :
"F code relay broadcasting" or "F code confidential reception" is "Inhibited with
soft SW."
<1>DCN is received for SUB. --- Check the box number.
<2>DCN is received for SID. --- Check the box number and pass code.
In F code receiving :
"F code relay broadcasting" or "F code confidential reception" is "Inhibited with
soft SW."
<S><R>
67
F PASS # NG
In F code receiving, the pass code (SID) is not matched.
<R>
68
BOX NO NG
In F code reception, a box number which is not registered is specified.
(SUB is not matched.)
(SUB is not matched.)
<R>
69
MEMORY OVER
Memory over in quick online sending
<S>
70
(JOB MEMORY OVER)
In PC-FAX reservation, the number of remote parties is exceeded.
<S>
71
NG71XXXX*
In PC-FAX reservation, data sent from PC includes some errors.
<S>
72
NG72XXXX*
In department management setting on the machine side:
•In reservation from PC-FAX or PC-IFAX, a department number which is not
•In reservation from PC-FAX or PC-IFAX, a department number which is not
registered on the machine side is specified.
•In reservation from PC-FAX or PC-IFAX, the department number is not specified.
<S>
<S>
73
NG73XXXX*
In reservation from PC-FAX or PC-IFAX, the use quantity limit is exceeded.
<S>
74
NG74XXXX*
When reserving specified filing in document filing in PC-FAX or PC-IFAX;
•The pass-code for the folder is set on the machine side and the pass-code from
•The pass-code for the folder is set on the machine side and the pass-code from
PC-XXX does not match with it.
•The pass-code for the folder is set on the machine side and no pass-code is
specified by PC-XXX.
<S>
<S>
75
NG75XXXX*
Reservation cannot be made due to machine busy. (Reservation of PC-FAX
cannot be accepted.) (This does not occur in Dragon.)
cannot be accepted.) (This does not occur in Dragon.)
<S>
76
NG76XXXX*
Reserved with receive confirmation request in PC-IFAX, but the IFAX sender is
not registered on the machine side.
not registered on the machine side.
<S>
77
NG77XXXX*
In reserving specified filing in PC-FAX or PC-IFAX, the machine has no filing
function.
function.
78
NG78XXXX*
When making a reservation of filing designation by PC-FAX or PC-IFAX, the filing
function on the machine is inhibited.
function on the machine is inhibited.
80
NG80XXXX*
NIC connect failure (Network abnormality)
•Check for disconnection of cables.
•Check for disconnection of cables.
•A network trouble (CE-xx) occurs.
•The port is set to disable.
•Authentication by the POP server is failed when POP before SMTP setting is
•Authentication by the POP server is failed when POP before SMTP setting is
valid.
81
NG REPORT
In internet FAX send, reply of receive confirmation of the remote machine is not
normal. (Including PC-IFAX).
•Error of the disposition-modifier .
•The disposition modifier is not in an error, and the disposition type is other than
normal. (Including PC-IFAX).
•Error of the disposition-modifier .
•The disposition modifier is not in an error, and the disposition type is other than
displayed, dispatched, or processed.
82
NO REPORT
In internet FAX send, time-out occurs in waiting for receive confirmation from the
remote machine. (Including PC-IFAX).
•In a case where send confirmation wait time-out time is other than 0, when send
remote machine. (Including PC-IFAX).
•In a case where send confirmation wait time-out time is other than 0, when send
confirmation reply from an internet FAX destination is not received.
•Recalls of the set number of recalls are performed, but send confirmation reply
from an internet AFX destination is not received.
83
NG LIMIT
In E-mail/FTP, internet FAX send, the send data size exceeds the upper limit of
send data.
send data.
84
REJECTED
In e-mail receive, a sender is registered in receive reject address/domain.
<R>
85
NG85XXXX*
In e-mail receive, an error occurs in communication with POP3 server.
•Header acquisition error.
•Header acquisition error.
•Time-out during mail receive
Report code
(Communication
result)
Display in the column of result
Content of communication interruption
Means of
communication
[07]MACHINEOPERATION.fm 7 ページ ２００４年１２月１５日 水曜日 午後２時２２分
AR-FX12 MACHINE OPERATION 7-8
*
For a job status result in "Display in the column of result," "NG
XXXX" is displayed. "
" is the code number.
For a communication result, "Communication error
" is displayed.
•When the communication result is OK, the communication sub code 1 and the communication sub code 2 are "0000."
•Errors in ( ) are not used in this machine.
(2) Communication report code list 2
•For report codes 16 ~ 31, V.34 MODE COMMUNICATION.
86
RECEIVED
In e-mail receive, an unsupported attached file is received. Only the TIFF-F type
is supported for attached files.
•The TIFF-F type of the attached file cannot be recognized.
•There is no attached file.
is supported for attached files.
•The TIFF-F type of the attached file cannot be recognized.
•There is no attached file.
87
NG87XXXX*
In e-mail receive, an attached file cannot be stored in memory.
•Memory over
•Memory over
88
NG88XXXX*
In SMTP e-mail receive, an attached file cannot be stored in memory.
•Cannot be stored in memory.
•Cannot be stored in memory.
•The number of items of acting receive data is the maximum, and an additional
data cannot be stored.
89
NG89XXXX*
In SMTP e-mail receive, an error occurs in communication with the mail server.
•Time-out occurs during e-mail receive.
•Time-out occurs during e-mail receive.
90
NG90XXXX*
After reservation by re-operation of document filing, conversion for image send
cannot be made.
cannot be made.
Report code
Final receive signal (Send side)
Final receive signal (Receive side)
Remark
0
Abnormal signal
Abnormal signal
1
NSF, DIS
(SID), (SUB), NSS, DCS
2
CFR
(PWD), (SEP), NSC, DTC
3
FTT
EOP
4
MCF
EOM
5
PIP, PIN
MPS
6
RTN, RTP
PRI-Q
7
No signal, DCN
DCN
8
PPR
PPS-EOP
9
PPS-EOM
10
PPS-MPS, PPS-NULL
11
RNR
RR
12
CTR
CTC
13
ERR
EOR-Q
14
PPS-PRI-Q
15
16
Abnormal signal
Abnormal signal
V.34 MODE COMMUNICATION
17
NSF, DIS
SID, SUB, NSS, DCS
V.34 MODE COMMUNICATION
18
CFR
PWD, SEP, NSC, DTC
V.34 MODE COMMUNICATION
19
FTT
PPS-EOP
V.34 MODE COMMUNICATION
20
MCF
PPS-EOM
V.34 MODE COMMUNICATION
21
PIP, PIN
PPS-MPS, PPS-NULL
V.34 MODE COMMUNICATION
22
RTN, RTP
PRI-Q
V.34 MODE COMMUNICATION
23
No signal, DCN
DCN
V.34 MODE COMMUNICATION
24
PPR
V.34 MODE COMMUNICATION
25
RNR
RR
V.34 MODE COMMUNICATION
26
CTR
CTC
V.34 MODE COMMUNICATION
27
ERR
EOR-Q
V.34 MODE COMMUNICATION
28
PPS-PRI-Q
V.34 MODE COMMUNICATION
29
V.8Phase-1
V.8Phase-1
V.34 MODE COMMUNICATION
30
V.8Phase-2
V.8Phase-2
V.34 MODE COMMUNICATION
31
V.8Phase-3
V.8Phase-3
V.34 MODE COMMUNICATION
Report code
(Communication
result)
Display in the column of result
Content of communication interruption
Means of
communication
[07]MACHINEOPERATION.fm 8 ページ ２００４年１２月１５日 水曜日 午後２時２２分
Click on the first or last page to see other AR-FX12 (serv.man7) service manuals if exist.