Sharp AR-F14 (serv.man3) Service Manual ▷ View online
AR-F14/PN1 UNPACKING AND INSTALLATION 3-5
18) Install the stapler unit into the finisher.
<1>Remove the packing the tape (two pieces) from the locations
shown in the illustration.
<2>Open the finisher front cover and insert the stapler unit.
19) Attach the exit tray to the finisher.
<1>Hang the two pawls of the exit tray on the finisher.
<2>Use the four screws D to secure the exit tray.
<2>Use the four screws D to secure the exit tray.
At this time, check that the positioning dowel is securely
inserted.
20) Check and adjust the height of the finisher.
Bring the finisher close to the copier and check that the guide pin is
inserted smoothly into the connecting hole of the finisher.
If the guide pin should not be inserted smoothly, adjust as follows.
a. If the guide pin is deviated from the finisher connecting hole:
<1>Loosen the adjustment section securing screw on the rear side.
<2>Remove the cap with a flat-blade screwdriver or the like and use
<2>Remove the cap with a flat-blade screwdriver or the like and use
the height adjusting screw to adjust the position so that the guide
pin matches the center of the finisher connecting hole.
<3>Loosen the adjustment section securing screw on the front side.
<4>If the guide pin can be inserted smoothly, tighten the adjusting
section securing screws on the front side and the rear side and
attach the cap.
attach the cap.
b. If the guide pin matches the finisher connecting hole:
<1>Push the finisher into the copier.
Guide pin
[03]UNPACKINGANDINSTALLATION.fm 5 ページ ２００４年４月２７日 火曜日 午後７時４分
AR-F14/PN1 UNPACKING AND INSTALLATION 3-6
<2>If the gap between the copier and the finisher is not uniform at
the upper and lower parts, remove the caps from the front side
and the rear side of the finisher stand with a flat-blade
screwdriver or the like.
Then, remove the screws of the front and rear subcovers (one
Then, remove the screws of the front and rear subcovers (one
screw for each) and then remove the subcovers.
<3>Loosen the four adjustment section securing screws located at
the positions shown in the illustration and then rotate the front
and rear height adjusting screws so that the gap becomes
uniform.
<4>If the gap becomes uniform, tighten the adjustment section
securing screws and reattach the caps and the subcovers.
21) Connect the connector of the finisher.
Connect the connector of the finisher to the connector of the docking
unit.
Connect the connector of the finisher to the connector of the copier
and then tighten the screws.
22) Set the staple cartridge in the stapler unit.
<1>Open the finisher front cover and pull out the stapler unit.
<2>Turn the roller rotating knob unit the triangle mark is aligned with
the index.
<3>Insert the staple cartridge securely into the staple section unit it
clicks.
Note: Check also that the right and left parts of the staple
cartridge do not float.
<4>Insert the staple section and close the finisher front cover.
23) Paste the stapling position label.
Paste the stapling position label to the document feeder.
Insert the power plug of the copier to the outlet and turn on the main
switch of the copier.
switch of the copier.
Gap
Gap
Staple position label
[03]UNPACKINGANDINSTALLATION.fm 6 ページ ２００４年４月２７日 火曜日 午後７時４分
AR-F14/PN1 UNPACKING AND INSTALLATION 3-7
2. AR-PN1
<Before installation>
For installation of AR-PN1A/PN1B/PN1C/PN1D, a saddle stitch finisher
(AR-F14) must have been installed.
1) Turn off the main switch of the main unit.
<1> Then remove the power plug of the main unit from the outlet.
<2> Remove the connector of the finisher.
<2> Remove the connector of the finisher.
2) Remove the front cabinet and the rear cabinet from the finisher.
<1> Open the front door of the finisher and remove the jam handling dial.
<2> Remove the two front cabinet securing screws, pull out the staple
unit until it stops, then remove the pawl of the front cabinet in the
direction indicated by the arrow and remove the front cabinet..
<3> Remove the three rear cabinet securing screws, remove the pawl in
the direction indicated by the arrow, and remove the rear cabinet.
At this time, remove the relay harness through the opening of the
At this time, remove the relay harness through the opening of the
rear cabinet.
Parts included
Screw
(M4 x 6 with rosette)
: 1 pc.
Harness A (purple): 1 pc.
Harness B (orange): 1 pc.
Dust box label:
1 sheet
Hole punch position label*:
2 sheets
* Will not be used.
Use the hole punch
position labels packed
in AR-F14
position labels packed
in AR-F14
OFF
Jam handling dial
Staple unit
Screws
Front cabinet
Pawl
Screw
Relay harness
Opening for
relay harness
relay harness
Screw
Rear
cabinet
cabinet
Pawl
[03]UNPACKINGANDINSTALLATION.fm 7 ページ ２００４年４月２７日 火曜日 午後７時４分
AR-F14/PN1 UNPACKING AND INSTALLATION 3-8
3) Remove the top cover.
<1> Remove the four top cover securing screws and remove the top
<1> Remove the four top cover securing screws and remove the top
cover.
<2> Remove the four pawls from the top cover and separate the cover
into the upper and lower portions. Reuse the upper portion.
4) Remove the paper entry PG.
<1> Remove the dust box.
<2> Remove the screws (2 pcs.) which are fixing the beak PG
(paper entry PG).
<3> Remove the boss on the upper side of the paper entry PG.
<4> Remove the boss on the lower side of the paper entry PG with a
straight-slot screwdriver.
<5> Remove the beak PG (paper entry PG).
<6> Replace the dust box to the original position.
Top cover
Screw
Pawl
Pawl
Top cover
1
[03]UNPACKINGANDINSTALLATION.fm 8 ページ ２００４年４月２７日 火曜日 午後７時４分
Click on the first or last page to see other AR-F14 (serv.man3) service manuals if exist.