Sharp AR-F12 (serv.man2) Service Manual ▷ View online
CHAPTER 1 GENERAL DESCRIPTION
1-24
E.
Supplying the Saddle
Stitch Unit with Staples
(Saddle Finisher)
Stitch Unit with Staples
(Saddle Finisher)
If the host machine indicates the saddle stitch
unit staple supply message, perform the following
to supply it with staples.
to supply it with staples.
1)
Open the front lower cover.
Figure 1-330
2)
Slide out the stitch unit.
Figure 1-331
3)
Pull the stitch unit to the front once, and then
shift it up.
shift it up.
Figure 1-332
4)
Hold the empty cartridge on its sides, and
remove it.
remove it.
Figure 1-333
5)
Set a new cartridge.
Figure 1-334
Reference
You must always replace both cartridges at the
same time.
same time.
CHAPTER 1 GENERAL DESCRIPTION
1-25
6)
Pull the stitch to the front once, and then
return it to its original position.
return it to its original position.
Figure 1-335
7)
Push in the stitch unit, and close the front
cover.
cover.
Figure 1-336
F.
Removing Staple Jams
from the Saddle Stitch
Unit (Saddle Finisher)
from the Saddle Stitch
Unit (Saddle Finisher)
If the host machine indicates the saddle stitch
unit staple jam message, perform the following to
remove the jam.
remove the jam.
1)
Open the front lower cover.
Figure 1-337
2)
Slide out the stitch unit.
Figure 1-338
3)
Pull the stapler of the stitch unit to the front
once, and then shift it up.
once, and then shift it up.
Figure 1-339
CHAPTER 1 GENERAL DESCRIPTION
1-26
4)
Hold the cartridge on its sides, and remove it.
Figure 1-340
5)
Push down on the area identified as A, and
pull up the tab identified as B.
pull up the tab identified as B.
Figure 1-341
6)
Remove the staple jam, and return the tab B
to its original position.
to its original position.
Figure 1-342
7)
Return the cartridge to its original position.
Figure 1-343
8)
Pull the stitch of the stitch unit to the front
once, and then return it to its original posi-
tion.
once, and then return it to its original posi-
tion.
Figure 1-344
9)
Push the stitch unit back to its original posi-
tion, and close the front lower cover.
tion, and close the front lower cover.
Figure 1-345
Reference
Whenever you have removed a staple jam, be sure
to execute staple edging.
to execute staple edging.
CHAPTER 1 GENERAL DESCRIPTION
1-27
G.
Removing Paper Jams
from the Puncher Unit
(option)
from the Puncher Unit
(option)
If the display indicates a paper jam on the
puncher unit, perform the following to remove the
jam:
jam:
1)
Open the front cover of the puncher unit.
Figure 1-346
2)
Align the triangle mark on the knob within
the range marked by .
the range marked by .
Figure 1-347
3)
Close the front cover of the puncher unit.
Figure 1-348
4) Holding the finisher unit as shown, move it to
detach it from the most machine.
Figure 1-349
5) Remove any jam visible from the outside.
Figure 1-350
6) Open the upper cover, and check the inside of
the finisher.
Figure 1-351
7) Lift the buffer roller cover, and remove the
jam.
Figure 1-352
Click on the first or last page to see other AR-F12 (serv.man2) service manuals if exist.