Sharp AR-651 (serv.man16) Service Manual ▷ View online
AR-651/810 TRANSFER/TRANSPORT UNIT 13 - 5
[B] Transfer belt
(1) Remove the transfer belt unit.
(2) Turn the transfer belt keeping/feeding section
90 degrees and pull it out upward.
(3) Remove 2 screws.
Note: When tightening up the screws, tighten them so
that the link plate is securely fixed by pushing it
toward the direction of the white arrows.
(4) Turn the drive roller as the picture shows.
(5) Pull out the transfer belt.
Notes: 1. When installing the transfer belt, install it
at the center not to be moved aside.
2. Do not touch the surface of the belt with bare
hands.
AR-651/810 TRANSFER/TRANSPORT UNIT 13 - 6
[C] Brush
(1) Remove the transfer belt keeping/feeding section.
(2) Remove 1 screw and take off the plate spring.
(3) Move the transport guide to the rear side and
pull it out upward.
(4) Remove 1 clip and take off 3 gears.
Notes: 1. The gears a/c has a latch, and remove the
gears in the order a, b, c.
2. When installing each gear, make sure the
latch fits into the groove portion of the shaft.
[D] Cleaning blade
(1) Remove the transfer belt keeping/feeding
section.
(2) Remove 3 screws and take off the cleaning
blade.
Notes: 1. When installing the cleaning blade, make
sure that both sides of the bosses are fit in
and screwed shut.
2. Do not touch the blade with bare hands
and make any scar on it.
3. Be careful not to mash the urethane seals at
both sides.
1
2
c
a
b
1
2
Clip
Bushing
(5) Remove 1 clip and take off the bushing.
(6) Push the brush to the rear side, take off
the front side shaft and pull out the brush upward.
Note: Do not touch the top of the brush with bare hands.
Urethane seal
AR-651/810 TRANSFER/TRANSPORT UNIT 13 - 7
[F] Transfer/Transport unit
(1) Open the front cover, turn the lever clockwise
and pull out the transfer/transport unit.
(2) Remove the fuser unit and transfer belt.
Note: When removing the transfer/transport unit,
remove each unit after removing the fuser and
transfer belt units.
(3) Remove 2 shoulder screws fixed at both sides
slide rails.
(4) Hold the A(shaft) or B(stay) section with the left
hand and the right slide rail with the right hand.
[E] Damp heater
(1) Remove the transfer belt unit.
(2) Remove 2 screws, disconnect 1 connector and
take off the damp heater.
Note: When installing the dump heater, be careful
not to catch it in the harness.
A
B
Dump
heater
heater
Connector
AR-651/810 TRANSFER/TRANSPORT UNIT 13 - 8
(6) Change the A or B section to the right hand
and hold the C section with the left hand. Then
lift the transfer/transport unit and take it off.
Notes: 1. Since the guide is sometimes transformed
when being pressured, be careful not to
hold the D section when lifting the transfer/
transport unit.
2. Take the following steps when installing
the transfer/transport unit.
1) Pull out only the left slide rail.
2) Hang the transfer/transport unit on the
left slide rail firmly.
3) Extend the right slide rail fully, especially,
its leading edge.
4) Hang the transfer/transport unit on the
right slide rail firmly.
5) Fix the transfer/transport unit with 2
shoulder screws.
6) Follow the reverse procedure of
disassembling afterwards.
(5)
쩸
Lift the transfer/transport belt unit and take
off the catch-up section.
쩹
Slack off the right slide rail a little.
쩺
Push the rail to the inside of the unit.
1
2
3
C
D
Click on the first or last page to see other AR-651 (serv.man16) service manuals if exist.