Sharp AR-405 (serv.man30) User Manual / Operation Manual ▷ View online
1-9
CHAPTER
1
Function setting icons
Selected special functions are indicated with their icons on
the basic screen. The setting screen for a selected function
can be easily called by pressing its icon. (The functions
indicated below with *1 have no setting screen and, therefore,
no setting screen can be called.)
If multiple special functions are selected, up to six icons
will be displayed.
the basic screen. The setting screen for a selected function
can be easily called by pressing its icon. (The functions
indicated below with *1 have no setting screen and, therefore,
no setting screen can be called.)
If multiple special functions are selected, up to six icons
will be displayed.
The function setting icons are listed below. The content of
the icons indicated by *2 will change depending upon the
particular settings for these functions.
the icons indicated by *2 will change depending upon the
particular settings for these functions.
USING THE TOUCH PANEL
GETTING STARTED
Using the touch panel
READY TO COPY.
1. A4
2. A3
READY TO COPY.
ERASE
EDGE ERASE
CENTRE ERASE
EDGE+CENTRE
ERASE
CANCEL
10
OK
OK
(0~20)
mm
mm
*
2
Margin shift (p.3-4)
*
2
Erase (p.3-6)
*
1
Dual page copying (p.3-8)
*
2
Multi shot (p.3-10)
*
2
Covers (p.3-13)
*
2
Transparency film with insert sheets
(p.3-15)
Pamphlet copy (p.3-17)
*
1
Centring (p.3-20)
*
2
Repeat copy (p.3-22)
*
1
B/W reverse (p.3-25)
*
1
Binding change (p.3-27)
Date (p.3-30)
Select stamp (p.3-33)
Watermark (p.3-36)
Page number (p.3-39)
2-1
CHAPTER
2
CHAPTER 2
MAKING COPIES
This chapter describes the basic copying functions such as normal
copying, reduction/enlargement, and exposure adjustments.
copying, reduction/enlargement, and exposure adjustments.
Page
●
●
●
●
●
AUDITING ACCOUNTS
.............................
2-2
●
●
●
●
●
USING THE RADF
.................................
2-3
●
●
●
●
●
COPYING FROM THE DOCUMENT GLASS
..............
2-8
●
●
●
●
●
REDUCTION/ENLARGEMENT/ZOOM
.................
2-11
●
●
●
●
●
SPECIAL PAPERS (manual feed)
....................
2-14
Two sided copying with bypass tray
....................
2-15
●
●
●
●
●
EXPOSURE ADJUSTMENTS
........................
2-16
●
●
●
●
●
SORT/GROUP
...................................
2-17
●
●
●
●
●
JOB MEMORY
...................................
2-18
●
●
●
●
●
INTERRUPTING A COPY RUN
.......................
2-20
2-2
CHAPTER
2
AUDITING ACCOUNTS
If this copier has been programmed in the auditing mode, it will not
function until an assigned 5-digit account number has been entered.
function until an assigned 5-digit account number has been entered.
★ KEY OPERATOR
See page 8-9 for setting the auditing mode.
MAKING COPIES
Auditing accounts
The initial status of the message display will be:
ENTER YOUR ACCOUNT NUMBER.
●
Enter your account number using the 10-key pad.
●
As each digit is entered, the dashes in the display will change to
asterisks.
asterisks.
The following message will appear after the number is entered.
ACCOUNT STATUS: COPIES MADE 000,000
COPIES REMAINING 000,000
“COPIES REMAINING” will appear only if account limit has been
set using a key operator program.
set using a key operator program.
★
★
★
★
★ KEY OPERATOR
See page 8-12 for account limit settings.
●
The message will be displayed for several seconds, then change
to the following message.
to the following message.
READY TO COPY.
●
When a copy run is performed, the following message will
appear.
appear.
READY TO COPY.
PRESS [AUDIT CLEAR] WHEN FINISHED.
(In some regions, [ACC.#-C] is displayed in place of [AUDIT
CLEAR].)
CLEAR].)
●
In the interrupt copy mode (see page 2-20), the following
message will appear instead of the message above.
message will appear instead of the message above.
READY TO COPY. WHEN COPYING IS
FINISHED, PRESS [INTERRUPT].
NOTE:
If an unassigned number is entered, the message display will show
“
If an unassigned number is entered, the message display will show
“
ENTER YOUR ACCOUNT NUMBER.-----
”, indicating that the
number was not accepted.
When the key operator program of account number security has
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
been set:
If an unassigned number is entered three successive times, the
copier will not accept another number for one minute, and the
following message will appear.
PLEASE SEE YOUR KEY OPERATOR FOR
ASSISTANCE.
★
★
★
★
★ KEY OPERATOR
See page 8-13 for account number security.
1
2
3
4
5
6
7
8
9
0
C
P
CLEAR
PROGRAM
AUDIT CLEAR
INTERRUPT
Click on the first or last page to see other AR-405 (serv.man30) service manuals if exist.