Sharp AR-285 (serv.man2) Handy Guide ▷ View online
TEST SIMULATION
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
25
VERSION 1
JANUARY 2002
Test
Command
Sub
Code
Description
26
35
Trouble memory mode setting
36
ICU fan activation temperature set up
40
Polygon motor stop mode set up
41
Used to disable/enable auto magnification
44
Used to set up SCSI I/F of ICU PWB
46
Used to set up image rotation
50
Sets reverse image enable/disable
52
Blank Paper Count Mode Setup
30
--
Main body sensors
01
Main unit sensor check
02
Tray sensor check
40
--
Bypass tray sensor check
01
Bypass tray size sensor check
02
Bypass tray adjustment
41
--
Original size detection (OC mode)
01
PS sensor check
02
PS sensor adjustment
03
PS sensor output display
43
01
Fuser temperature set up
03
Adjusts fuser motor speed
08
Sets rotation time after warm up
03
Adjusts fuser motor speed
08
Sets rotation time after warm up
44
--
Process control mode
01
Correction mode setting
02
PC gain adjustment
04
PC initial density set up (drum type B)
05
Correction initial bias set up (drum type B)
09
PC data display
12
DM data, patch/base data display
15
Drum control set up (drum type A)
46
-- Exposure
adjustment
02
Exposure level set up copier 2
17
Used to execute shading correction and display value
18
Adjusts the density gradient in copy mode
19
Adjusts density gradient & sets detection area in AE
20
Copy density correction in SPF/ RSPF mode (AR507)
48
01 Magnification
adjustment
50
--
Lead edge registration
01
Lead edge adjustment value (copy)
02
Lead edge adjustment value (calculation)
Cont’d
TEST SIMULATION
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
26
VERSION 1
JANUARY 2002
Test
Command
Sub
Code
Description
50
05
Adjust print edge position
10
Print centre deviation adjustment.
12
Original centre deviation adjustment.
26
Folding margin of centre binding setting
51
01
PSPS timing set up
02
Resist roller adjustment value
03
Clutch Off time setting (AR-507 only)
08
Used to enable/disable PSPS timing for each paper
feed section
feed section
52
01
ADU alignment plate home position setting
53
--
Document Feeder adjustments
01
DF stop position setting
02
RADF sensor adjustment
06
Adjusts RSPF width detection (AR507 only)
60
01 DRAM
test
61
--
Laser unit
01
Laser unit check
02
Laser power value setting (drum type B)
04
Adjusts scanner laser power in printer mode
62
-- Hard
drive
01 HDD
format
02
HDD read/write test partial check
03
HDD read/write test all area check
63
01
CCD shading data display
07
White plate scanning start positionadj. (AR507 only)
64
01 Self
print
65
-- Touch
panel
01
Touch panel adjustment
02
Touch panel test
67
01
Printer PWB memory operation check
02
Printer Parallel I/F operation check
03
Adjust Parallel I/F Ack signal width
11
Used to set printer I/F select in signal
12
Used to write data into printer flash memory
13
Used to check printer flash memory data
14
Printer flash memory data writing & result
15
Used to check the sum of the printer flash memory
16
Used to check the operation of the network card
17
NVRAM data clear (printer pwb)
18
Data Clear (Network scanner)
69
01
Used to check input/output of scsi channels A and B
(AR507 only)
(AR507 only)
TROUBLE CODES
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
27
VERSION 1
JANUARY 2002
Sub
Content of trouble
Code
Sub
Content of trouble
CE 00
Communication error has occurred
F9 90
Printer communication trouble
01
AR-NC3D is not installed ot defective
H3 00
Thermistor open (HL1)
02
Specified Mail Server or FTP server not found
01
Thermistor open (HL2)
03
Server does not correspond during image TX
H3 00
Heat roller high temperature detection (HL1)
04
Entered account name is invalid
01
Heat roller high temperature detection (HL2)
05
Entered directory of the FTP server is invalid
H4 00
Heat roller low temperature detection (HL1)
Cl 00
MC trouble
01
Heat roller low temperature detection (HL2)
C2 00
TC trouble
H5 01
5 continuous POD not-reaching JAM detection
E7 00
ICU communication trouble
02
Fusing thermistor abnormality
01
Image data memory trouble
L1 00
Scanner feed trouble
02
Laser trouble
L3 00
Scanner return trouble
03
HDD trouble
L4 01
Main motor lock detection
10
Shading trouble (Black correction)
L6 10
Polygon motor lock detection
11
Shading trouble (White correction)
L8 01
No full-wave signal
13
CCD light quantity check error
02
Full-wave signal width abnormality
90
CU communication trouble
U2 00
EEPROM read/write error
Fl 00
Finisher communication trouble
11
Counter check sum error
01
Finisher 1 jogger shift trouble /
12
Adjustment value check sum error
02
Finisher transport motor abnormality
U4 02
ADU alignment plate operation abnormality
04
Finisher 1 elevator lower limit /
03
ADU rear plate operation abnormality
Finisher 2 stack tray lower limit
U5 00
RADF/RSPF/SPFcommunication trouble
05
Finisher 1 elevator home /
01
RADF resist sensor trouble
Finisher 2 stack tray sensor abnormality
02
RADF expulsion sensor trouble
06
Finisher shift motor abnormality
03
RADF timing sensor trouble
08
Finisher staple shift motor trouble
06
RSP post-separation sensor trouble
10
Finisher staple unit operation trouble
07
RSPF read sensor trouble
11
Finisher 1 pusher motor trouble /
08
RSPF SB sensor trouble
Finisher 2 boomerang rotation abnormality
11
RADF paper feed motor operation abnormality
14
Finisher 2 stack tray abnormality
16
RSPF fan motor trouble
15
Finisher 1 elevator motor trouble /
U6 00
Desk communication trouble
Finisher 2 stack tray motor lock
01
Desk1 CS lift up trouble
16
Staple sort holding motor
02
Desk2 CS lift up trouble
17
ST paper exit roller pressure release trouble
08
Desk 24v power abnormality
18
Tray 3 paper exit paddler operation trouble
10
Desk transport motor trouble
50
Non-support trouble in automatic detection
20
LCC communication trouble
80
Finisher power not supplied
21
LCC transport motor trouble
F2 00
Toner control sensor open
22
LCC 24v power abnormality
02
Toner motor connector unconnected
50
Non supported option connection (Desk Unit)
31
Process control trouble (Drum surface reflection)
51
Non supported option connection (LCC Unit)
32
Process control trouble (Drum Mark)
U7 00
RIC communication trouble
37
Drum marking sensor gain adjustment error
U9 00
Operation control communication trouble (ICU)
39
Process thermistor breakdown
90
Operation control communication trouble (OPE)
F3 12
Copier top stage CS lift up trouble
EE EL
Auto developer adjustment trouble - Overtone
22
Copier bottom stage CS lift up trouble
EU
Auto developer adjustment trouble - Undertone
F9 00
Printer communication trouble
FA 01
A2 board self diag error (memory)
01
PRT DRAM trouble
FC 00
ASK/IrDA modulation LSI reset error
02
PRT Centroport check error
01
ASK/IrDA switch error
03
Network card trouble
PC
Personal counter not installed
04
Printer program error
PF
RIC copy inhibit command reception
05
Short of memory capacity on the ICU PWB
- -
Auditor not Ready
10
PRT SCSI LSI abnormality
JAM CAUSE CODES
SHARP ELECTRONICS (UK) LTD
DOCUMENT SYSTEMS GROUP
28
VERSION 1
JANUARY 2002
CODE
CONTENTS
Copier Body
MFT
Bypass tray paper jam (PPD2 not reached)
TRAY1
Tray1 paper feed jam (PFD not reached)
TRAY2
Tray2 paper feed jam (PFD not reached)
DUP
Duplex feed jam
(PPD2 not reached)
PFD_ND1
PFD not reached jam (Desk tray1 paper feed)
PFD_ND2
PFD not reached jam (Desk tray2 paper feed)
PFD_ST1
PFD remaining jam (Copier tray1 paper feed)
PFD_ST2
PFD remaining jam (Copier tray2 paper feed)
PFD_SD1
PFD remaining jam (Desk tray1 paper feed)
PFD_SD2
PFD remaining jam (Desk tray2 paper feed)
PPD1_NT2
PFD1 not reached jam (Copier tray2 paper feed)
PPD1_ND1
PFD1 not reached jam (Desk tray1 paper feed)
PPD1_ND2
PFD1 not reached jam (Desk tray2 paper feed)
PPD1_NLC
PFD1 not reached jam (LCC paper feed)
PPD1_ST1
PFD1 remaining jam (Copier tray1 paper feed)
PPD1_ST2
PFD1 remaining jam (Copier tray2 paper feed)
PPD1_SD1
PPD1 remaining jam (Desk tray1 paper feed)
PPD1_SD2
PPD1 remaining jam (Desk tray2 paper feed)
PPD1_SLC
PPD1 remaining jam (LCC paper feed)
PPD2_NT1
PPD2 not reached jam (Copier tray1 paper feed)
PPD2_NT2
PPD2 not reached jam (Copier tray2 paper feed)
PPD2_ND1
PPD2 not reached jam (Desk tray1 paper feed)
PPD2_ND2
PPD2 not reached jam (Desk tray2 paper feed)
PPD2_NLC
PPD2 not reached jam (LCC paper feed)
PPD2_SMF
PPD2 remaining jam (Bypass paper feed)
PPD2_ST1
PPD2 remaining jam (Copier tray1 paper feed)
PPD2_ST2
PPD2 remaining jam (Copier tray2 paper feed)
PPD2_SD1
PPD2 remaining jam (Desk tray1 paper feed)
PPD2_SD2
PPD2 remaining jam (Desk tray2 paper feed)
PPD2_SLC
PPD2 remaining jam (LCC paper feed)
PPD2_SAD
PPD2 remaining jam (Duplex paper feed)
Click on the first or last page to see other AR-285 (serv.man2) service manuals if exist.