DOWNLOAD Sharp AR-285 (serv.man12) Service Manual ↓ Size: 877.93 KB | Pages: 118 in PDF or view online for FREE

26 - 2

Purpose

Setting

Function
(Purpose)

1) Used to set the paper size of the large quantity paper tray. (When the paper size is changed, the lift paper size must

be also changed with this simulation.) 

2) Used to detect the paper or document size of 8.5" x 13" (Inch series) and set the display mode. (All paper feed modes)

Section

Paper transport

Item

Specifications

Operation/
Procedure

1. Select the item to be set with [

↑

] key and [

↓

] key.

A: Large capacity paper tray paper size setting
B: 8.5" x 13" (330mm/13") paper size detection mode setting

2. Enter the code number corresponding to the paper size of the large capacity paper feed tray with the 10-key and press

the [OK] key. 

Set value 

Setting size 

1

8.5

✕

11

2

A4 (Default)

3

B5

2’. Used to set the size detection mode when 8.5" x 13" paper or document is used.

Enter the code number with the 10-key pad and press the [OK] key.

 Detection size when 8.5" x 13" document/paper is used

Unit

Destination

Set value

 0 

 (Default)

(Invalid)   

1

(Valid)

Document

AR-SP1

All destinations

8.5" x 14"

8.5" x 13"

*1

AR-AF1
AR-RF1

Japan

A4R

A4R

*5

EX AB series  (SLK/SEEG)

A4R

A4R

*5

EX AB series  (SCA/Others)

A4R

8.5"  x  13"

*3

Inch series (SEC/SECL)

8.5" x 14"

8.5" x 14"

*5

Inch series (Others)

8.5" x 14"

8.5" x 13"

*1

Document table

Japan/EX AB series

B4

8.5" x 13"

*2

Inch series

8.5" x 14"

8.5" x 13"

*1

Paper

Main body

Manual feed tray

All destinations

8.5" x 14"

8.5" x 13"

*4

Paper feed cassette All destinations

        —      *6

AR-DE1/DE2

All destinations

AR-LC1

All destinations

—

*1: A document of 8.5" x 14" is detected as 8.5" x 13".
*2: A document of B4 is detected as 8.5" x 13".
*3: A document of A4R is detected as 8.5" x 13".
*4: A document of 8.5" x 14" is detected as 8.5" x 13".
*5: Applicable by replacing the document set tray of the AR-AF1/RF1.
*6: Setting is available with the key operator program (P40).

Note

8 – 67

26 - 3

Purpose

Setting

Function
(Purpose)

Used to set the specifications of the auditor. Setting must be made depending on the use condition of the auditor.

Section

Auditor

Item

Specifications

Operation/
Procedure

Enter the code number corresponding to the auditor specification mode with the 10-key pad and press the [OK]
key.

Set value 

Specification mode 

1

Built-in auditor mode (Default)

2

Coin vendor 

3

Others 

Note

26 - 5

Purpose

Setting

Function
(Purpose)

Used to set the count mode of the total counter and the maintenance counter.

Section

Item

Specifications

Counter

Operation/
Procedure

Used to set the single count-up or double count-up for the total counter, the maintenance counter, and the
developer counter when printing is performed with A3, 11 x 17" paper,
1. Select the kind of the counter with [

↑

] and [

↓

] key.

A

Total

B

Maintenance

C

Developer

2. Enter "1" or "2" with the 10-key pad and press the [OK] key.

1 : Single count
2 : Double count

Default: 2

Note

8 – 68

26 - 6

Purpose

Setting

Function
(Purpose)

Used to set the specifications depending on the destination.

Section

Item

Specifications

Destination

Operation/
Procedure

Select the destination referring to the table below.

U.S.A.

United States of America

Canada

Canada

Inch

Inch series, other destinations

Japan

Japan

AB_B

AB series (B5 detection) other destinations

Europe

Europe

U.K.

United Kingdom

Aus.

Austrailia

AB_A

AB series (A5 detection) other destinations

When the destination setting is changed, the following specification is changed.
(Toner save mode setup specification) (Paper specification)

Note

8 – 69

26 - 15

Purpose

Setting

Function
(Purpose)

Used to set the fusing operation mode (paper curl corresponding mode).

Section

Fixing (Fusing)

Item

Operation

Operation/
Procedure

Due to the paper type (paper property), paper may be curled in the fusing section to cause a paper jam. To
prevent against this, the fusing conditions is changed.
Enter the code number corresponding to the fusing condition and press the [OK] key. 

Set value 

Remedy mod

Fusing condition

0

Normal operation 

(Default)

1

Remedy mode 1

a. Racing until the specified fusing temperature is reached.

2

Remedy mode 1

a. Racing is performed until the specified fusing temperature is reached.

b. Copy mode is duplex mode or sort.

Group mode 

•

  Previous rotation is made for 5 sec before starting copying.

Note

26 - 18

Purpose

Setting

Function
(Purpose)

Used to set VALID/INVALID of toner save operation. (This simulation is valid only in the Japan and UK versions.
(It depends on SIM 26-6 (Destination setting). For the other destinations, the same setting can be executed with
theuser program..)

Section

Item

Specifications

Operation mode (Common)

Operation/
Procedure

Enter the code number corresponding to the condition (the toner save YES/NO) with the 10-key and press the
[OK] key.

Set value 

Toner save 

0

YES 

1

NO (Default)

Note

8 – 70