Sharp AR-285 (serv.man12) Service Manual ▷ View online
In the case of AR-FN1
JGHP
Jogger motor home sensor
READY
Stapler self priming sensor
PSHP
Pusher motor home sensor
STUHP
Staple unit home sensor
T2PF
Tray 2 paper full sensor
STND
Stapler replacement sensor
EVRE
Elevator motor encoder
OFHP
Offset home sensor
STHP
Staple home sensor
INPD
Paper entry sensor
RVPD
Reverse paper exit sensor
PGOP
Upper transport PG open/close sensor
PFD1
Transport sensor 1
PFD2
Transport sensor 2
PFD3
Transport sensor 3
PFD4
Transport sensor 4
T3OD
Tray 3 paper exit sensor
STID
Staple tray paper entry sensor
STPD
Staple paper sensor
T1PF
Tray 1 paper full sensor
T3UP
Tray 3 upper limit sensor
T3DN
Tray 3 lower limit sensor
LSTS
Stapler sensor
NCTS
Staple cartridge sensor
PWD
Power off detection
DSW1
Copier connection detection
DSW2
Top door open/close detection
DSW3
Front door open/close detection
Note
8 – 34
3 - 3
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of the loads in the sorter and the control circuit.
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
The display differs depending on the unit (sorter, finisher) which is installed.
1. The names of the loads which can be operated are displayed. Select The selected load is highlighted.
The selected load is highlighted.
2. Press the [EXECUTE] key, and the selected load is operated.
During the operation of the load, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed when it is highlighted, the operation is interrupted.
If the [EXECUTE] key is pressed when it is highlighted, the operation is interrupted.
In the case of AR-SS1
DTM
Transport motor
DCM
Holder motor
BZ
Buzzer
TMM
Bin shift motor
DSM
Alignment motor
SAM
Stapler drive motor
In the case of AR-FN1
PSM
Pusher motor
JGM
Jogger motor
STUM
Staple unit shift motor
FML
Main drive motor low transport speed
FMH
Main drive motor high transport speed
RVM
Reverse motor
EVM
Elevator motor
OFM
Offset motor
INGSL
Paper entry gate solenoid
T3UPSL
Tray 3 upper limit solenoid
OG1SL
Paper exit gate 1 solenoid
OG2SL
Paper exit gate 2 solenoid
OG3SL
Paper exit gate 3 solenoid
RRSL
Reverse roller pressure release solenoid
SPSL
Short path select solenoid
STSL
ST paper holding solenoid
T12CL
Tray 1 and tray 2 speed reduction clutch
PDCL
Paddler clutch
STOPCL
ST paper exit roller pressure clutch
T3SLCL
Tray 3 speed reduction clutch
STM
Staple motor
T3ORSL
Tray 3 normal speed clutch
8 – 35
Note
3 - 6
Purpose
Adjustment
Function
(Purpose)
(Purpose)
Used to adjust the finisher stacking capability. (Used to adjust the stop position of the finishser paper width
direction alignment plate (jogger). This adjustment is made by changing the width direction alignment plate home
position by the software.)
(Target model:AR-S330/280/285/335)
direction alignment plate (jogger). This adjustment is made by changing the width direction alignment plate home
position by the software.)
(Target model:AR-S330/280/285/335)
Section
Sorter/Finisher
Item
Operation
Operation/
Procedure
Procedure
1. Select B mode with [
↑
] and [
↓
] keys.
2. Select the paper size by entering the numbers (0 or 1) with the 10-key pad.
3. Select A mode with [
↑
] and [
↓
] keys.
4. Enter the adjustment value with the 10-key pad.
5. Press the [EXECUTE] key.
The value entered in procedure 4 is set.
The finisher’s jogger starts operation. During operation, the [EXECUTE] key is highlighted.
If the [EXECUTE] key is pressed while it is highlighted, the load operation is interrupted.
If the [EXECUTE] key is pressed while it is highlighted, the load operation is interrupted.
Note
8 – 36
4
4 - 2
Purpose
Operation test/check
Function
(Purpose)
(Purpose)
Used to check the operation of sensors and detectors in the paper feed section (desk feed, large capacity tray)
and the related circuit.
and the related circuit.
Section
Paper transport
Item
Operation
Operation/
Procedure
Procedure
The operating conditions of the sensors and detectors in the paper feed section are displayed.
The active sensors and detectors are highlighted.
The active sensors and detectors are highlighted.
Desk Unit Sensor
LCC Unit Sensor
DDOPSW
Door open sensor
LRE
Remaining quantity sensor
DPOD1
Paper exit transport sensor 1cs
LUD
Upper limit sensor
DPOD2
Paper exit transport sensor 2 cs
LDD
Lower limit sensor
DPOD3
Paper transport sensor 3cs
LPED
Paper empty sensor
DLUD1
1cs Lift upper limit sensor
LPFD
Paper exit sensor
DPED1
1cs Paper empty sensor
LDSW
Door open SW
DCSPD1
1cs remaining quantity detection 1
LTOD
Body connection sensor
DLUD2
2xs lift upper limit sensor
LCD
Cassette detection line
DPED2
2cs paper empty sensor
LLSW
Upper limit switch.
DCSPD2
2cs remaining quantity detection 1
DLUD3
3cs lift upper limit sensor
DPED3
3cs paper empty sensor
DCSPD3
3cs remaining quantity detection 1
FOUND1
1cs lift unit detection (Installation detection)
FOUND2
2cs lift unit detection (Installation detection)
FOUND3
3cs lift unit detection (Installation detection)
DCSS11
1cs size detection 0
DCSS12
1cs size detection 1
DCSS13
1cs size detection 2
DCSS14
1cs size detection 3
DCSS21
2cs size detection 0
DCSS22
2cs size detection 1
DCSS23
2cs size detection 2
DCSS24
2cs size detection 3
DCSS31
3cs size detection 0
DCSS32
3cs size detection 1
DCSS33
3cs size detection 2
DCSS34
3cs size detection 3
Note
8 – 37
Click on the first or last page to see other AR-285 (serv.man12) service manuals if exist.