Sharp AR-161 (serv.man22) User Manual / Operation Manual ▷ View online
44
GENERAL INFORMA
TION
Setting the power save modes
The time that elapses before the copier enters a power save mode after any
operation is made can be set manually. This time is set with user program No.
2 for the preheat mode and user program No. 3 for the auto power shut-off
mode. For these settings, see page 37.
operation is made can be set manually. This time is set with user program No.
2 for the preheat mode and user program No. 3 for the auto power shut-off
mode. For these settings, see page 37.
●
The copier will enter the preheat mode first and then the auto power shut-
off mode after a preset time has elapsed when no copier operation has
been made.
off mode after a preset time has elapsed when no copier operation has
been made.
●
If conflicting settings are made with user programs No. 3 and No. 5, the
last program set will have priority.
last program set will have priority.
Copying from the preheat mode
Make desired copier selections and press the START
key using the normal copying procedure.
key using the normal copying procedure.
●
When any key input is made or any other copier operation is made, the
POWER SAVE indicator will start to blink.
POWER SAVE indicator will start to blink.
●
When the START key is pressed, the START key indicator will go out
and copying will start within 10 seconds. The POWER SAVE indicator
will go out when copying starts.
and copying will start within 10 seconds. The POWER SAVE indicator
will go out when copying starts.
Copying from the auto power shut-off mode
1
Press the START key.
●
The copier will exit the auto power shut-off mode and the POWER
SAVE indicator will start to blink.
SAVE indicator will start to blink.
2
Make desired copier selections and press the START
key using the normal copying procedure.
key using the normal copying procedure.
●
It will take approximately 35 seconds for the copier to start copying.
However, you can make desired settings and press the START key
during warm-up. Copying will start after warm-up is finished.
However, you can make desired settings and press the START key
during warm-up. Copying will start after warm-up is finished.
Power save modes
POWER SAVE MODES
45
GENERAL INFORMA
TION
USER MAINTENANCE
Proper care is essential for clean, sharp copies. Please take a few minutes to
regularly clean your copier.
regularly clean your copier.
Original table and platen cover
Stains or dirt on the original table or platen cover will
also be copied. Wipe the original table and platen cover
with a soft, clean cloth.
also be copied. Wipe the original table and platen cover
with a soft, clean cloth.
●
If necessary, dampen the cloth with water. Do not use thinner,
benzene, or similar volatile cleaning agents.
benzene, or similar volatile cleaning agents.
User maintenance
●
If an optional single pass feeder is installed, wipe the scanning window
on the original table.
on the original table.
Transfer charger
If copies start becoming streaky or blotchy, the transfer
charger may be dirty. Clean the charger. The cleaning
method is described on page 69, TRANSFER CHARGER
CLEANING.
charger may be dirty. Clean the charger. The cleaning
method is described on page 69, TRANSFER CHARGER
CLEANING.
Bypass tray paper feed roller
If misfeeds occur frequently when feeding postcards,
envelopes, thick paper, etc. through the bypass tray,
wipe the blue paper feed roller at the feed slot of the
bypass tray with a soft, clean cloth dampened with
alcohol or water.
envelopes, thick paper, etc. through the bypass tray,
wipe the blue paper feed roller at the feed slot of the
bypass tray with a soft, clean cloth dampened with
alcohol or water.
Paper feed roller
46
GENERAL INFORMA
TION
Problem
Solution
●
Copier plugged in?
●
Power switch ON?
●
Copy density properly adjusted?
●
Is the original placed face down?
●
Paper too heavy?
●
Paper damp?
●
Is transfer charger clean?
●
Non-standard paper used?
●
Paper properly installed?
●
Pieces of paper inside copier?
●
Paper curled or damp?
Plug the copier into a grounded outlet.
See page 8.
See page 8.
Turn the power switch ON.
See page 14.
See page 14.
See pages 14 and 26.
Place the original face down on the original
table.
table.
Use copy paper within the specified range.
See page 49.
See page 49.
Replace with dry copy paper.
Be sure to store copy paper in a dry location.
See page 50.
Be sure to store copy paper in a dry location.
See page 50.
Clean the transfer charger.
See page 69.
See page 69.
Use standard paper. If using special paper,
feed the paper through the bypass tray.
See pages 18 and 49.
feed the paper through the bypass tray.
See pages 18 and 49.
Make sure the paper is properly installed. See
pages 10 and 18.
pages 10 and 18.
Remove all pieces of misfed paper.
See page 31.
See page 31.
Store copy paper flat in the wrapper in a dry
location. See page 50.
location. See page 50.
Copier does not operate.
Copies are too dark or
too light.
too light.
Blank copies
Paper misfeeds frequently.
Copies smear if rubbed.
COPIER TROUBLE?
Copier trouble?
Striped copies
47
GENERAL INFORMA
TION
Problem
Solution
●
Original table or platen cover
dirty?
dirty?
●
Original smudged or blotchy?
●
Is the
indicator on?
●
Is the COPY indicator off?
●
Is copying, printing or facsimile
printing being performed?
printing being performed?
●
Is the POWER SAVE indicator
blinking?
blinking?
●
Is only the POWER SAVE
indicator on?
indicator on?
●
Is the COPY indicator off?
●
Is
steadily lit in the copy
quantity display?
●
Is the
indicator on?
Clean regularly. See page 45.
Use a clean original.
Maintenance is required. Contact your
SHARP service centre as soon as possible.
SHARP service centre as soon as possible.
Use the COPY/FAX key to select the COPY
mode. See Note below.
mode. See Note below.
Set the paper size after copying, printing or
facsimile printing is complete.
facsimile printing is complete.
Wait until warm-up is complete.
Warm-up time is approximately 35 seconds.
Warm-up time is approximately 35 seconds.
The copier is in the auto power shut-off
mode. Press the START
mode. Press the START
key. See page 43,
POWER SAVE MODES.
Use the COPY/FAX key to select the COPY
mode. See Note below.
mode. See Note below.
The copier is in the auditing mode.
Enter your account number using the
numeric keys. See page 13.
Enter your account number using the
numeric keys. See page 13.
Copy paper is needed. See page 10,
LOADING COPY PAPER.
LOADING COPY PAPER.
Copies are smudged or
dirty.
dirty.
Power is on but copying
is not possible.
is not possible.
Copier trouble?
COPIER TROUBLE?
Paper size for a paper
tray cannot be set.
tray cannot be set.
COPY/FAX key
The COPY/FAX key is used to switch
between the FAX and COPY modes.
For details, see the MULTI ACCESS
manual.
between the FAX and COPY modes.
For details, see the MULTI ACCESS
manual.
Click on the first or last page to see other AR-161 (serv.man22) service manuals if exist.