Sharp AM-400 (serv.man8) Service Manual ▷ View online
AM-400DE
2 – 13
3.4.2 Life clear mode
This mode is used for clearing life counters.
(a) Life all clear
Press the [ENTER] key, and the life counters of the printer and the life
counter of the scanner are set to 0.
counter of the scanner are set to 0.
Note: The value for Top void is not cleared.
(b) Life each clear
This mode is used to respectively clear the life counter of the printer
and the counter of the scanner. Select the desired counter and press
[ENTER] key.
and the counter of the scanner. Select the desired counter and press
[ENTER] key.
Note: If “5: TONER” is executed, both “TONER PAGE” and “TONER
DOTCOUNT” are cleared.
DOTCOUNT” are cleared.
3.5. Top void adjust
This mode is used for adjusting the top margin for printing.
3.5.1 Pattern print
For the print pattern, a graduation scale is printed on the leading edge
of the paper with figures. Enter the smallest figure as a top void value.
of the paper with figures. Enter the smallest figure as a top void value.
3.5.2 Void setting
Enter a top void value.
Input range: [0 - 40]
3.6. Print adjust
This mode is used to set some values about the printer.
3.6.1 Fan MD time set
This mode is used to set the driving time of the fan motor after stop-
ping the main motor.
ping the main motor.
• Default value: 02
• Input Range: MIN: 00, MAX: 63
• Unit: Minute
After entering the value, the Printer Adjust mode ends and the next
mode is displayed.
mode is displayed.
3.6.2 Tray temp.
This mode is used to set the temperature of fixing when printing from
the standard tray.
the standard tray.
1. ON TEMP.
The temperature to start turning on the heater.
• Default value: 190
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
2. OFF TEMP.
The temperature to start turning off the heater.
• Default value: 190
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
3. FEED TEMP.
The temperature to start feeding the paper.
• Default value: 190
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
4. TIME
Warming up time after reaching the temperature that the printing
can be done.
can be done.
• Default value: 10
• Range: MIN: 10, MAX: 63
• Unit: Second
[>]Key
1: LIFE CLEAR ALL
2: LIFE CLR EACH
2: LIFE CLEAR
[>]Key
1: SCAN(ADF)
3: PRINT
4: DRUM
5: TONER
[>]Key
[ENTER]Key
[>]Key
[>]Key
[>]Key
[ENTER]Key
[ENTER]Key
[ENTER]Key
[ENTER]Key
LI FE CLE AR
LI FE CLE AR
LI FE CLE AR
LI FE CLE AR
LI FE CLE AR
(a)[ENTER]Key
(b)[ENTER]Key
[>]Key
2: SCAN(FB)
[ENTER]Key
LI FE CLE AR
TOP VOID ADJUST
[ENTER]Key
1: PATTERN PRINT
2: VOID SETTING
[>]Key
PRINT ADJUST
[ENTER]Key
FAN MD_TIME SET
TRAY TEMP.
[>]Key
[>]Key
BYPASS TEMP.
[>]Key
FLICKER ADJUST
[>]Key
PARAMETERL IST
[>] Ke y
FAN MD_TIME SET
[ENTER]Key
FAN MD_TIME( 02 )
Cursor position
TRAY TEMP.
ON temp.=190 deg
OFF temp.=190 deg
FEED temp.=190 deg
TIME=10(s)
[ENTER]Key
[>]Key
[>]Key
[>]Key
[>]Key
Input temperature using the numeric keys
Input temperature using the numeric keys
Input temperature using the numeric keys
Input temperature using the numeric keys
AM-400DE
2 – 14
3.6.3 Bypass temp.
This mode is used to set the temperature of fixing when printing from
the bypass tray.
the bypass tray.
1. ON TEMP.
The temperature to start turning on the heater.
• Default value: 200
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
2. OFF TEMP.
The temperature to start turning off the heater.
• Default value: 200
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
3. FEED TEMP.
The temperature to start feeding the paper.
• Default value: 200
• Range: MIN: 170, MAX: 233
• Unit: Centigrade
4. TIME
Warming up time after reaching the temperature that the printing
can be done.
can be done.
• Default value: 10
• Range: MIN: 10, MAX: 63
• Unit: Second
3.6.4 Flicker adjust
This mode is specified the number of table for the countermeasures of
“FLICKER”.
“FLICKER”.
• Default value: 06
• Input Range: MIN: 00, MAX: 63
• Unit: -
3.6.5 Parameter list
Printing the parameter for fixing.
3.7. Test mode
This mode is used for printer aging on the two modes.
3.7.1 Motor aging
1. The motor aging starts with heater on or with heater off.
2. To exit the aging, press [STOP] key.
3.7.2 Charger adjust
This mode is used to check the high-pressure control.
1. Operation
1. Press the [ENTER] key to operate the mode.
2. Press the [STOP] key to exit this mode.
3.7.3 Paper feed
This mode is used to check Mechanical Controller in the High speed
mode.
mode.
Note: This mode is not used actual printing.
1. Operation
1. Press the [ENTER] key to operate the mode.
2. Press the [STOP] key to exit this mode.
[>]Key
BYPASS TEMP.
ON temp.=200 deg
OFF temp.=200 deg
FEED temp.=200 deg
TIME=10(s)
[ENTER]Key
[>]Key
[>]Key
[>]Key
Input temperature using the numeric keys
Input temperature using the numeric keys
Input temperature using the numeric keys
Input temperature using the numeric keys
FLICKER ADJUST
[ENT ER]K ey
FLICKER NO.=06
PARAMETER LIST
[ENT ER]K ey
PRINTING
TEST MODE
[ENTER]Key
1: MOTOR AGING
2: CHARGER ADJUST
[>]Key
[>]Key
3: PAPER FEED
[>]Key
5: PRINT SIZE
[>]Key
4: COM TEST
[>]Key
1: MOTOR AGING
[ENTER]Key
HT 1: ON 2: OFF
MM_AGING: HT_ON
MM_AGING: HT_OFF
[1]Key
[2]Key
2: CHARGER ADJUST
[ENTER]Key
NOW ADJUSTING
3: PAPER FEED
[ENTER]Key
NOW AGING
AM-400DE
2 – 15
3.7.4 COM test mode
You can check the communication between the main CPU and the
printer controller on this mode. Concretely, input the command number
from the main CPU and can read the response from the printer control-
ler.
printer controller on this mode. Concretely, input the command number
from the main CPU and can read the response from the printer control-
ler.
1. Operation
1. Press the [ENTER] key to enter the mode.
2. Select the mode “SR”, “EC”, “EEC”, or “ESR” using the “<“ or the
“>” key. The “>” key can be used to select the mode only when a
cursor is in the position of (a).
“>” key. The “>” key can be used to select the mode only when a
cursor is in the position of (a).
3. Enter the value using the numeric keys.
“SR”, “EC”, “ESR”
• Range MIN: 00, MAX: 31
“EEC”
• Range MIN: 00, MAX: 63
4. Press the [STOP] key to exit this mode.
3.7.5 Print size
This function is prepared for the function in the future. Now there is no
meaning.
meaning.
1. Operation
4. How to make soft switch setting
To enter the soft switch mode, press the following key entries in sequence.
[ENTER]Key
SR
=
ESR
=
4: COM TEST
[>]Key
[>]Key
[>]Key
ex)[1],[2]Key
ex)[1],[2]Key
(a) cursor position
SR12
=01
ESR12
=15
EC
=
[>]Key
ex)[1],[2]Key
EC12
=10
EEC
, =
ex)[1],[2],[3],[4]Key
EEC12,34
= 80 13
Enter paper size on bypass tray with numeric key and press the [ENTER] key.
PRINT SIZE
Press [ENTER]Key
SIZE=215. 9x279. 4
Press MENU
9
8
7
START
Press MENU key.
Press
key.
Press
key.
Bit1 - 8 are set.
Soft SW01 - SW99 are set.
SW01 = 1 0 0 0 0 0 0 0
SW01 = 1 0 0 0 0 0 0 0
SW01 = 1 0 0 0 0 0 0 0
SW01 = 1 0 0 0 0 0 0 0
SW02 = 0 0 0 0 0 0 0 0
SW99 = 0 0 0 0 0 0 0 0
Press
key during setting.
To finish the settings halfway between
SW01 and SW99, press the STOP
key. In this case, the setting being done
to the SW No. on display will be nullified
while settings done to the preceding
SW No. remain in effect.
SW01 and SW99, press the STOP
key. In this case, the setting being done
to the SW No. on display will be nullified
while settings done to the preceding
SW No. remain in effect.
The soft switch mode is terminated.
SW01 = 0 0 0 0 0 0 0 0
ENTER
DATA No. 1 2 3 4 5 6 7 8
When the QUALITY key is pressed, the
contents of soft switches are printed.
contents of soft switches are printed.
ENTER
AM-400DE
2 – 16
5. Soft switch description
5.1. Soft switch
SW
NO.
DATA
NO.
ITEM
Switch setting and function
Initial setting
Remarks
1
0
DE
F
IT
SE
H
SW1
1
2
3
4
2
3
4
Recall interval
0
1
0
1
1
0
1
0
1
0
1
1
0
1
0
1
0
1
1
0
1
0
1
0
1
1
0
1
0
1
0
1
1
0
1
5
6
7
8
6
7
8
Recall times
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
SW2
1
2
3
4
2
3
4
Memory retransmission
times
times
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
5
6
7
8
6
7
8
Memory retransmission
interval
interval
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
SW3
1
2
3
4
2
3
4
Number of rings for auto-
receive (0: No ring receive)
receive (0: No ring receive)
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
0
0
0
1
0
0
1
5
6
6
COPY/FAX/SCAN mode
COPY
FAX
SCAN
SCAN
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
No. 5
0
0
1
1
No. 6
0
1
0
1
7
Receive mode
AUTO
MANUAL
1
1
1
1
1
8
Reserved
0
0
0
0
0
Binary input
No. = 8 4 2 1
1 2 3 4 (Data No.)
EX 0 1 0 1
eg. Recall interval is set 5 min.
eg. Recall interval is set 5 min.
Binary input
No. = 8 4 2 1
5 6 7 8 (Data No.)
EX 0 0 1 0
eg. Recall times is set 2 times
eg. Recall times is set 2 times
Binary input
No. = 8 4 2 1
1 2 3 4 (Data No.)
EX 0 0 0 1
eg. Retransmission time set to 1 time.
eg. Retransmission time set to 1 time.
Binary input
No. = 8 4 2 1
5 6 7 8 (Data No.)
EX 0 0 1 0
eg. Retransmission interval to 2 minutes.
eg. Retransmission interval to 2 minutes.
Binary input
No. = 8 4 2 1
1 2 3 4 (Data No.)
EX 0 0 0 1
eg. Number of rings for auto receive is set to 1.
eg. Number of rings for auto receive is set to 1.
Click on the first or last page to see other AM-400 (serv.man8) service manuals if exist.