DOWNLOAD Sharp AL-1622 (serv.man20) Service Manual ↓ Size: 46.56 MB | Pages: 127 in PDF or view online for FREE

AL-1611/AL-1622

SIMULATIONS

8 – 4

*

2: Display after clearing each counter 000 

(0.75 sec) 

3

 Blank (0.35 sec) 

3

 000 (0.75 sec) 

3

 Blank (1.0 sec) 

3

 Repetition

7

6

Intermittent aging

After completion of warmup, counting is stopped and the ready lamp is 
lighted. When the copy quantity is entered and the start key is pressed, copy-
ing is made to make the set quantity of copies. After 3 sec standby, copying is 
made again to make the set quantity of copies. After that this operation is 
repeated. The paper size does not matter.

1 ~ 99

8

Warmup time display

Execute the simulation input with the copier side cover open, then close the 
side cover, and the machine will starts warming up. Warm up time is counted 
up every 2nd and it is displayed.

1 ~ 99

8

1

Developing bias voltage 
output check

Used to out put the developing bias for 30 sec. For the adjustment procedure 
of the developing bias, refer to the previous descriptions.

2

Main charger voltage output 
check (Grid bias high mode)

Used to output the main charger grid bias voltage at the high mode for 30 sec. 
For the adjustment procedure of the main charger grid bias voltage, refer to 
the previous descriptions.

3

Main charger voltage output 
check (Grid bias low mode)

Used to output the main charger grid bias voltage at the low mode for 30 sec. 
For the adjustment procedure of the main charger grid bias voltage, refer to 
the previous descriptions.

6

Transfer charger voltage 
check

Used to output the transfer charger voltage for 30 sec. For the adjustment pro-
cedure of the transfer charger voltage, refer to the previous descriptions.

9

1

Duplex motor forward rota-
tion operation check 

Used to rotate the duplex motor forward for 30 sec.

2

Duplex motor reverse rota-
tion operation check 
<Not Used>

Used to rotate the duplex motor reversely for 30 sec.

4

Duplex motor rotation speed 
adjustment 

The currently set duplex motor rotation speed set value is displayed. When 
the set value is entered and the start key is pressed, the set value is stored.

6

1  ~  13

5

Duplex motor switchback 
time adjustment

The currently set duplex motor switchback time set value is displayed. When 

the set value is entered and the start key is pressed, the set value is stored.

50

18 ~ 76

10

Toner motor operation check Used to operate the toner motor for 30 sec.

Note: If this simulation is executed with the toner hopper installed, toner is

automatically supplied to the developer. Be careful of overtoner.

14

Trouble (except for U2) 
cancel

Used to cancel troubles except for U2.

16

U2 trouble cancel

Used to cancel U2 trouble.

20

1

Maintenance counter clear

Used to clear the maintenance counter. 

*

2

21

1

Maintenance cycle setting

Used to display the currently set maintenance cycle at the numbers shown at 
right. When the set value is entered and the start key is pressed, the set value 
is stored.

2

0  ~  7

Main 
code

Sub 

code

Contents

Details of operation

Initial 
value

Set range

Key operation

Copy quantity setting: Copy quantity keys

Key operation

Duplex motor rotation speed set value: Copy quantity keys

Key operation

Duplex motor switchback time set value: Copy quantity keys

Key operation/Display

0: 2500 sheets

1: 5000 sheets

2: 25000 sheets (When toner save is ON)
3: 50000 sheets (When toner save is ON)

4: 150000 sheets

5: FREE (999999 sheets)

6: 10000 sheets
7: 7500 sheets

AL-1611/AL-1622

SIMULATIONS

8 – 5

*

1: Each counter display method 

To display 123456: 123 (0.75 sec) 

3

 Blank (0.35 sec) 

3

 456 (0.75 sec) 

3

 Blank (1.0 sec) 

3

 repetition

*

2: Display after clearing each counter 

000 (0.75 sec) 

3

 Blank (0.35 sec) 

3

 000 (0.75 sec) 

3

 Blank (1.0 sec) 

3

 Repetition

Main 
code

Sub 

code

Contents

Details of operation

Initial 
value

Set range

21

2

Mini maintenance cycle set-
ting 

Used to display the currently set mini maintenance cycle at the numbers 
shown at right. When the set value is entered and the start key is pressed, the 
set value is stored.

4

0  ~  4

22

1

Maintenance counter display Used to display the current maintenance counter value. 

*

1

2

Maintenance preset value 
display

Used to display the current maintenance preset value (set with SIM 21-1). 

*

1

3

JAM memory display

Used to display a JAM generated during copying on the JAM position display 
on the operation panel. Max. 30 recent jams are stored. JAM No. 1 is dis-
played even when there is no JAM.

4

Total JAM counter display

Used to display the current total JAM counter value. 

*

1

5

Total counter display

Used to display the current total counter value. 

*

1

6

Developing counter display

Used to display the current developing unit counter value. 

*

1

7

Developing preset counter 
value display 

Used to display the current mini maintenance preset value (set with SIM 21-2). 

*

1

8

SPF counter display 
<Only AL-1622>

Used to display the current SPF counter value. 

*

1

9

Paper feed counter display

Used to display the current paper feed counter value for each paper feed port. 

*

1

12

Drum counter display

Used to display the current drum counter value. 

*

1

14

Copier ROM version display

Used to display the version number of the main ROM.

15

Trouble memory display

Used to display the actually occurred trouble codes on the display on the 
operation panel. When the start key is pressed during the main code display, 
the sub code is displayed. Max. 20 recent trouble codes are stored.

Key operation/Display

0: 2500 sheets

1: 5000 sheets

2: 10000 sheets
3: FREE (999999 sheets)

4: 30000 sheets (When toner save is OFF)

50000 sheets (When toner save is ON)

Key operation

Display

JAM history select:  

Magnification ratio display key

The history number (1 ~ 30) is 
displayed on the display. 
The JAM position LED correspond-
ing to the history number is lighted.

Key operation

Paper feed port selection: Tray select key

Display

(Example) When the ROM version is 4.01:

004 

3

 Blank 

3

 001 

3

 Blank 

3

 Repetition

Key operation

Display

Sub code display: Start key

Trouble code history select: 

Magnification ratio display key

Histories 1 ~ 10: The upper digit of  

display "A" ~ "J" lights up.

Histories 11 ~ 20: The upper digit of  

display "A" ~ "J" blinks.

•  Display without trouble code Main

code: "– –" 
Sub code: "00"

AL-1611/AL-1622

SIMULATIONS

8 – 6

*

2: Display after clearing each counter 

000 (0.75 sec) 

3

 Blank (0.35 sec) 

3

 000 (0.75 sec) 

3

 Blank (1.0 sec) 

3

 Repetition

Main 
code

Sub 

code

Contents

Details of operation

Initial 
value

Set range

22

16

Duplex print counter display

Used to display the current duplex print counter value. 

*

1

17

Copy counter display

Used to display the current copy counter value. 

*

1

18

Printer counter display  

Used to display the current printer counter value. 

*

1

19

Electronic sort counter dis-
play  
<Not Used>

Used to display the current electronic sort counter value. 

*

1

21

Scanner counter display

Used to display the current scanner counter value.

24

1

JAM memory, JAM counter 
clear

Used to clear the JAM memory and the JAM counter. 

*

2

2

Trouble memory clear

Used to clear the trouble memory. 

*

2

4

SPF counter clear 

Used to clear the SPF counter. 

*

2

5

Duplex counter clear 
<Not Used>

Used to clear the duplex counter. 

*

2

6

Paper feed counter clear

Used to clear the paper feed counter. 

*

2

7

Drum counter clear

Used to clear the drum counter. 

*

2

8

Copy counter clear

Used to clear the copy counter. 

*

2

9

Printer counter clear 

Used to clear the printer counter. 

*

2

10

Electronic sort counter clear 

Used to clear the electronic sort counter. 

*

2

13

Scanner counter clear

Used to clear the scanner counter. 

*

2

25

1

Main motor operation check

Execute the simulation with the developer cartridge removed, and the main 
motor will rotate for 30 sec. At that time, the cooling motor rotates at a low 
speed.

10

Polygon motor operation 
check

Used to drive the polygon motor for 30 sec.

AL-1611/AL-1622

SIMULATIONS

8 – 7

Main 
code

Sub 

code

Contents

Details of operation

Initial 
value

Set range

26

1

Option switch display

Used to display the installed option on the operation panel. (The LED corre-
sponding to the installed option is lighted.)

3

Auditor setting

Used to display the current auditor setting with the numbers at right. After 
entering the set value, press the start key, and the set value is stored.

0

0  ~  2

5

Counter mode setting

Used to set the print counter mode in A3. 
Used to display the currently set counter value with the numbers at right. After 
entering the set value, press the start key, and the set value is stored.

0

0  ~  3

6

Destination setting

Used to display the current destination setting with the numbers at right. 
After entering the set value, press the start key, and the set value is stored.

8

0  ~  13

Key operation

Display

Display select: 

Magnification 
ratio display key

<Lighting with an option installed>

When "A" is displayed:
Shifter: Paper empty LED

Job separator: JAM LED

SPF: SPF select LED
RSPF: SPF JAM LED

Duplex mode: Main cassette select LED

Simplex mode: Multi manual paper feed select LED
MCU JMPER1: Top of the magnification ratio display

MCU JMPER2: 2nd of the magnification ratio display

MCU JMPER3: 3rd of the magnification ratio display
MCU JMPER7: 4th of the magnification ratio display

MCU JMPER7: 5th of the magnification ratio display

MCU JMPER7: 6th of the magnification ratio display
MCU JMPER7: 7th of the magnification ratio display

MCU JMPER8: Bottom of the magnification ratio display

When "b" is displayed: 
Cassette (2nd step): No. 2 cassette select LED

Cassette (3rd step): No. 3 cassette select LED

Cassette (4th step): No. 4 cassette select LED
Memory installed: Paper empty LED

FAX: JAM LED

Printer: Main body JAM LED
ERDH: Main cassette select LED

16CPM: SPF JAM LED

20CPM: SPF select LED
Document sensor: Auto paper select LED

Key operation/Display

0: Built-in auditor
1: Coin vendor

2: Others

Key operation/Display

0: Total/Developer = 2 counts

1: Total/Developer = 1 count
2: Total/Developer = 2 counts

3: Total/Developer = 1 count

Maintenance = 2 counts

Maintenance = 2 counts
Maintenance = 1 count

Maintenance = 1 count

Key operation/Display

0: Japan
1: USA (Inch series)

2: Canada (Inch series)

3: Germany 1 (AB series)
4: UK (AB series)

5: Not used

6: France (AB series)

7: EX inch series

  8: X AB series
  9: X inch series (FC conformity)

10: EX AB series (FC conformity)

      (Australia, Newzealand)
11: China (AB series)

12: Taiwan (AB series)

13: Germany 2 (AB series)