DOWNLOAD Sharp AL-1555 (serv.man21) Service Manual ↓ Size: 1.65 MB | Pages: 37 in PDF or view online for FREE

If the MFP driver cannot be installed under Windows 2000/XP, check your computer's settings according to the following 
procedure.

Panel".
On Windows 2000, click the "Start" button, select 

"Settings", and then click "Control Panel".

click "System".
On Windows 2000, double-click the "System" icon.

Signing" button.
The following dialog box will open.

If the option "Block" has been selected for your 

computer, then the MFP driver will not be installable. 

Select the option "Warn" and then install the MFP driver 

as explained in "INSTALLING THE SOFTWARE" in the 

Operation Manual.

If print output is faint, uneven or smeared, follow the steps listed below.

You can select "Draft", "Normal" or "Photo" for the 

print quality in the "Advanced" tab of the printer 

driver setup screen. When "Photo" is selected, you 

can click the "Image Adjustment" button and adjust 

the brightness and contrast in the dialog box that 

appears. Adjust these settings appropriately for 

your print data and try printing again.

If the paper is curled, straighten it up and set it in 

the unit again.

Only paper weighing from 60 to 80g/m

2

 can be 

used in the paper tray. Only paper weighing from 52 

to 128g/m

2

 can be used in the multi-bypass tray 

and single bypass.

When it is near time to replace the TD cartridge or 

drum cartridge, the TD cartridge replacement 

required ( ) indicator or drum cartridge 

replacement required ( ) indicator will light 

steadily on the unit operation panel. When it is time 

to replace either cartridge, the indicator will blink. 

Replace the cartridge and try printing again.

Reference:

See "TD CARTRIDGE REPLACEMENT", 

"DRUM CARTRIDGE REPLACEMENT" 

and  "ABOUT SUPPLIES AND OPTIONS" 

in the Operation Manual.

If the margins are set outside of the quality 

guaranteed area, smudges or smears may appear 

at the upper and lower edges of the paper.

When selecting the paper settings in the 

application, set the margins from the top, bottom, 

left and right edges of the paper to 4 mm.

If a document is printed skewed or partly off the paper, follow the steps listed below.

Check if the "Paper Size" options suit the size of the 

paper loaded in the tray.

If the "Fit To Page" setting is activated, make sure 

that the paper size selected from the drop-down list 

of the "Fit To Paper Size" option is the same as the 

size of the loaded paper.

Click the "Paper" tab in the printer driver setup 

screen, and verify if the "Image Orientation" option 

is set to your requirements.

If a document is physically damaged when it is 

output or the image is skewed on the paper, discard 

the damaged sheet, reinsert the paper supply and 

print again. Insert the paper so that there is no 

visible space between the paper and the paper 

guides.

Reference:

See "LOADING PAPER" in the Operation 

Manual for more details on inserting paper.

Check the layout of the document margins and the 

paper size settings for the application you are 

using. Also check if the print settings are specified 

correctly to suit the paper size.

Reference:

If nothing prints even when the unit is turned on, please wait a few moments. The unit needs a longer time to process  
intricate data. If the unit still does not print, refer to the check list below.

When the misfeed ( ) indicator blinks or (

) 

blinks in the display, the unit will stop because of a 

misfeed.

Remove the jammed paper as explained in 

"MISFEED REMOVAL" in the Operation Manual.

The ON LINE indicator on the operation panel turns 

off while the unit is used for copying. Scanning and 

printing is not possible at this time. When copying is 

finished, the ON LINE indicator will turn on after the 

set auto clear time elapses, and the unit will be 

ready for scanning and printing. You can also press 

the clear (

) key twice or press the ON LINE key 

to make the unit ready for scanning or printing.

When choosing "Print" from the "File" menu located in 

applications, be sure you have selected "SHARP AL-

XXXX" printer displayed in the "Print" dialog box.

Check if the printer driver has been installed, following 

the steps listed below.

On Windows 95/98/Me/NT 4.0/2000, click the "Start" 

button, select "Settings" and then click "Printers".

If you still cannot print after confirming the "SHARP 

AL-XXXX" printer driver icon, the printer driver may 

not have been installed correctly. In this case, delete 

SHARP Personal MFP series software and then 

reinstall it.

Reference:

Check here.