DOWNLOAD Sharp PN-E471R (serv.man5) Service Manual ↓ Size: 5.86 MB | Pages: 43 in PDF or view online for FREE

E

9

OPTION

DATE/TIME SETTING

○

○

SCHEDULE

○

○

INPUT SELECT

DVI

-

○

BNC

-

○

HDMI

○

○

AUDIO SELECT

PC DVI-D

-

○

PC HDMI

○

○

PC D-SUB

-

○

PC RGB

-

○

AV DVI-D

-

○

AV HDMI

○

○

AV COMPONENT

-

○

AV S-VIDEO

-

○

AV VIDEO

-

○

INPUT SIGNAL

480 LINES

○

○

768 LINES

○

○

1050 LINES

○

○

ZOOM2 SPECIAL SETTING

○

○

SCAN MODE

○

○

POWER MANAGEMENT

○

○

COLOR SYSTEM

-

○

AUDIO OUTPUT

○

○

AUDIO INPUT LEVEL

○

○

SELF ADJUST

○

○

AUTO INPUT CHANGE

○

○

ENLARGE

ENLARGE H

○

○

ENLARGE V

○

○

ENLARGE-POS H

○

○

ENLARGE-POS V

○

○

BEZEL H

○

○

BEZEL V

○

○

H-POS

○

○

V-POS

○

○

PIP/PbyP

PIP MODES

○

○

PIP SIZE

○

○

PIP H-POS

○

○

PIP V-POS

○

○

PIP BLEND

○

○

PIP SOURCE

-

○

SOUND CHANGE

○

○

MAIN POS

○

○

PbyP2 POS

○

○

AUTO OFF

○

○

TIPS

•  Some items may not be displayed depending on the input mode.

E

10

The menu will differ depending on the input mode.

n

AUTO (PC D-SUB/PC RGB)
The CLOCK, PHASE, H-POS, and V-POS are automatically 

adjusted.

Pressing   performs adjustment.

Use this automatic adjustment when you use the PC D-sub 

input terminal or PC RGB input terminals to display a PC 

screen for the first time or when you change the setting of 

the PC. (See page 16.)
CLOCK (PC D-SUB/PC RGB)
Adjusts frequency for sampling clock for applicable video.

Adjust when there is flickering in the form of vertical stripes.

When using the adjustment pattern (see page 16), make 

adjustments so that no vertical stripe noise appears in it.
PHASE (PC D-SUB/PC RGB)
Adjusts sampling clock phase for applicable video.

Useful when small characters appear with low contrast and/

or there are flickers at corners.

When using the adjustment pattern (see page 16), make 

adjustments so that no horizontal stripe noise appears in it.

*  Adjustments to PHASE should be made only after CLOCK 

has been correctly set.

H-POS
Adjust the horizontal position of the image.
V-POS
Adjust the vertical position of the image.
H-SIZE
Adjust the horizontal size of the image.
V-SIZE
Adjust the vertical size of the image.
H-RESOLUTION (PC D-SUB/PC RGB)
Sets proper horizontal resolution when the resolution of 

input signals is not recognized properly. (Adjustment may be 

impossible with some signals.)
V-RESOLUTION (PC D-SUB/PC RGB)
Sets proper vertical resolution when the resolution of input 

signals is not recognized properly. (Adjustment may be 

impossible with some signals.)
RESET
Resets the values of the SCREEN menu items to the factory 

preset values.

Select “ON” and then press  .

n

AUTO (PC D-SUB/PC RGB)
The CONTRAST and BLACK LEVEL are automatically 

adjusted.
Pressing   performs adjustment.
CONTRAST
Adjusts the brightness of the image.
BLACK LEVEL
Adjusts the entire brightness of the video signals.
TINT
Adjusts the hue. Selecting + changes the color towards 

green, and selecting - changes it towards magenta.
COLORS
Adjusts the color intensity.
SHARPNESS
Adjusts the sharpness of the image.
ADVANCED (AV input)
You can adjust more specifically. (See page 16.)
COLOR MODE
Changes the color mode on the screen. The color mode on 

the screen can also be changed using a remote control unit. 

(See page 5.)

*  sRGB is PC input only. See page 5 for details.
WHITE BALANCE
THRU .............. Displays the input signal level as is. (for PC 

DVI-D/PC HDMI only)

PRESET ......... Selects the color temperature using PRESET.

USER .............. Used for adjusting R-CONTRAST, 

G-CONTRAST, and B-CONTRAST 

respectively.

PRESET
Selects the color temperature when the WHITE BALANCE is 

set to PRESET.

The setting values are shown for reference. The color 

temperature of the screen varies over time.

This function is not intended to keep the color temperature 

constant.
R-CONTRAST
Adjusts red component when the WHITE BALANCE is set to  

USER.
G-CONTRAST
Adjusts green component when the WHITE BALANCE is set 

to USER.
B-CONTRAST
Adjusts blue component when the WHITE BALANCE is set 

to USER.
COPY TO USER
Copies the value set for PRESET to the USER setting.
Select “ON” and then press  .
GAMMA
Select a gamma value. USER sets the gamma value 

transferred by the user. (See page 21.)
RESET
Resets the values of the PICTURE menu items to the factory 
preset values.
Select “ON” and then press  .

E

11

n

TREBLE
Adjusts the volume of treble-level sound.
BASS
Adjusts the volume of bass-level sound.
BALANCE
Adjusts the balance of the audio sound between right and left.
RESET
Resets the values of the AUDIO menu items to the factory preset values.
Select “ON” and then press  .

n

OSD H-POSITION
Adjusts the horizontal display position of menu screen.
OSD V-POSITION
Adjusts the vertical display position of menu screen.
MONITOR
Select the installation direction of the monitor.

LANDSCAPE ............Horizontal orientation

PORTRAIT ...............Vertical orientation
MONAURAL AUDIO
Outputs audio signals as monaural.
LANGUAGE
Sets the display language for the menu screen.
POWER ON DELAY
You can delay the screen display after the monitor is turned 

on. The period can be set up to 60 seconds in units of one 

second. When this function is activated, the power LED 

flashes (at approx. 1 second interval) in orange. This function 

is disabled when 0 is specified.
OPERATION MODE
MODE1 ......Limits the maximum brightness lower than 

MODE2. 

OFF IF NO OPERATION is set to ON, and 

STANDBY MODE is set to LOW POWER.  

(These settings can not be changed.)

MODE2 ......Will perform standard operation. 

OFF IF NO OPERATION is set to OFF, and 

STANDBY MODE is set to STANDARD. These 

settings can be changed.

STANDBY MODE
When STANDARD is selected, startup time from standby 

mode is reduced. Note, however that, more power will be 

consumed in standby mode.

When LOW POWER is selected, current consumption 

is reduced while the monitor is in standby mode. Note, 

however, that the startup time from standby mode becomes 

longer. Also, certain RS-232C commands cannot be used 

in standby mode, and control via LAN will be disabled. (See 

pages 22 and 29.)
OFF IF NO OPERATION
Determines whether or not to set the monitor to go into 

standby mode when there is no operation from the remote 

control unit, RS-232C commands, or LAN for over 4 hours.

HDMI SETTING
HDMI AUTO VIEW

 ......................... When ON is selected, the screen size is 

adjusted automatically according to the 

screen size control signal included in the 

video signal input from the AV HDMI input 

terminal.

HDMI RGB INPUT RANGE

 ......................... Sets the type of HDMI signals when using 

the AV HDMI input mode. 

When AUTO is selected, the type is set 

automatically.

HOT PLUG CONTROL
Sets whether to use hot plug control for the PC/AV HDMI 

and PC/AV DVI-D input terminals.
RS-232C/LAN SELECT
Selects the method with which to control the monitor from 

the computer.
ID No. SET
Assigns ID numbers to monitors connected in a daisy chain 

(see page 19), using RS-232 cables.

The numbers 1 to 255 are available for ID numbers.

If “0” is set, the system regards this as the state where no ID 

number is set.
BAUD RATE
Selects the communication speed used for RS-232C 

communication.
LAN SETUP
Configures the settings to control the monitor from the 

computer via LAN. (See page 29.)
SPEAKER SELECT
Selects the speaker to be used.
OPTION DC OUT SETTING
Normally, leave this setting as OFF.

When using an optional part, if instruction appears, change 

the setting accordingly.

E

12

AUTO INPUT CHANGE
Specify whether to change inputs automatically. When ON is 

selected and no signal is present in the selected input mode, 

AUTO INPUT CHANGE automatically changes the selected 

mode to another mode where a video signal is present.

When video signals exist in multiple input modes, the 

switching priority is as follows:

PC D-SUB, PC HDMI and AV HDMI

When the PN-ZB01 (optional) is attached:

PC DVI-D, PC HDMI, PC D-SUB, PC RGB, AV DVI-D, AV 

HDMI, AV COMPONENT, AV S-VIDEO and AV VIDEO

(Input mode switching may take 15 seconds or more, 

depending on the connected equipment. Input signals 

may not be detected properly and a priority may change, 

depending on the connected equipment or video signals.)

n

ENLARGE H
Sets the number of screen splits (number of monitors) in the 

horizontal direction used for the enlargement. (See page 14.)
ENLARGE V
Sets the number of screen splits (number of monitors) in the 

vertical direction used for the enlargement. (See page 14.)
ENLARGE-POS H / ENLARGE-POS V
Specify the split screen to be displayed when the 

enlargement function is used. (See page 14.)
BEZEL H / BEZEL V
Sets the frame width of the display when the enlargement 

function is used. 
H-POS
Adjust the horizontal position of the enlarged screen.
V-POS
Adjust the vertical position of the enlarged screen.

n

DATE/TIME SETTING
Set the date and time. Press   or   to select the date and 
time, and press   or   to change the numerical values.
Set the date in “Year/Month/Day” order.
Set the time on a 24-hour basis.
SCHEDULE (See page 15.)
You can set the time to switch the monitor on and off.
INPUT SELECT
Select the input mode to be used in PC/AV DVI-D input 

terminal, PC/AV HDMI input terminal and PC RGB/AV 

component input terminals.
AUDIO SELECT
Selects the terminal used to input audio signals in each input 

mode.
INPUT SIGNAL (PC D-SUB/PC RGB)
If a computer connected to the PC D-sub/PC RGB input 

terminal outputs any of the following resolutions, make a 

selection from the following options.

480 LINES .......... AUTO, 640x480 or 848x480

768 LINES ..........AUTO, 1024x768, 1280x768, or 1360x768

1050 LINES ........1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 14.)
SCAN MODE (AV input)
Sets the scan mode used for AV mode input.

MODE1 ............... Over-scan display

MODE2 ...............Under-scan display

MODE3 ............... Under-scan display when the input signal 

is 1080i/p. Otherwise, over-scan display

*  Even when MODE1 is selected, under-scan display is used when 

the input signal is 1080i/p and the screen size is Dot by Dot.

POWER MANAGEMENT
POWER MANAGEMENT determines whether or not to 

switch modes from no signal to the input signal standby 

mode.
COLOR SYSTEM (AV S-VIDEO/AV VIDEO)
Select the color system of the AV equipment which is 

connected to AV S-video and AV video input terminal. (AUTO 

/ PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43)  

When AUTO is selected, the color system is automatically 

set according to the input signal.
AUDIO OUTPUT
Sets the volume of sound output from the audio output 

terminals.

VARIABLE .......... You can adjust the volume using VOLUME.

FIXED .................Fixes the sounds.
AUDIO INPUT LEVEL
Selects the maximum audio input level of the audio input 

terminal.
SELF ADJUST
On a PC D-SUB/PC RGB screen, specify whether to 

perform screen adjustment automatically or not. When ON 

is selected, the screen is automatically adjusted when its 

resolution is 800 x 600 or higher and the timing of input 

signals changes. “ADJUSTING” appears on the screen 

during the adjustment. Depending on the signal, adjustment 

may not be possible. In this case select OFF. (Perform 

manual adjustment of the screen.)