DOWNLOAD Sharp PN-A601 (serv.man5) Service Manual ↓ Size: 8.4 MB | Pages: 60 in PDF or view online for FREE

49

E

49

This screen allows you to specify the general LAN settings.

MONITOR NAME
Specify a name for this monitor as it should appear on the 

Internet Explorer screen.
AUTO LOGOUT TIME
Specify the time (in minutes) to elapse before automatically

disconnecting this monitor from the network. 

Specify in minutes from 1 to 65535. A value of ‘0’ will disable

this function. 
DATA PORT
Specify the TCP port number to use for exchanging data with

the monitor. 

Specify a value from 1025 to 65535.
SEARCH PORT
Specify the port number to use when searching for this 

monitor. 

Specify a value from 1025 to 65535.
INSTALLATION INFORMATION (NAME/LOCATION)
Specify the information to display for this monitor in the 

Internet Explorer window.

TIPS

•  The MONITOR NAME can be up to 16 alphanumeric

characters or symbols. 

•  Enter up to 50 characters in the NAME field in the

INSTALLATION INFORMATION.

•  Enter up to 100 characters in the LOCATION field in the

INSTALLATION INFORMATION.

This screen allows you to configure the e-mail sent periodically

or when the monitor has an error.

The settings depend on the configuration of your LAN. Ask

your LAN administrator for details. 

SMTP SERVER
Specify the SMTP server address for sending e-mail.

*  When using a domain name, make sure to specify the

DNS SERVER as well. (See page 48.)

ORIGINATOR E-MAIL ADDRESS
Specify the e-mail address for this monitor.

This address becomes the e-mail address of the originator.
ORIGINATOR NAME
Specify the name for the originator. 

This name appears in the “Originator Name” field of the

e-mail.
AUTHENTICATION
Specify the authentication method to use when sending 

e-mail.
POP SERVER
If the “AUTHENTICATION” method is “POP before SMTP”,

specify the POP server address. 
ACCOUNT NAME / PASSWORD
If the “AUTHENTICATION” method is “POP before SMTP”,

specify the account name and password to connect to the 

POP server.  

TIPS

•  You can enter up to 64 alphanumeric characters or symbols

for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR

NAME, ACCOUNT NAME, and PASSWORD.

•  The SMTP SERVER and POP SERVER can be up to 64

characters. 

The following characters can be used: a-z, A-Z, 0-9, - , .

50

E

50

This screen allows you to specify the recipients of the e-mail

sent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSES
Specify the e-mail addresses to send error notification e-mail

to.
CONDITION
Specify the conditions to send mails. 

When you check PERIODICAL, specify the date and time to

send the mails in the PERIODICAL setting.
CONFIRMATION
Sends test e-mail.

This allows you to confirm that the e-mail settings are

configured properly.
Attach the log file to a TEMPERATURE/HARDWARE error 

e-mail.
When this option is checked, a log is added to the mail which

notifies a temperature or status error.

TIPS

•  The RECIPIENT E-MAIL ADDRESSES can be up to 64

alphanumeric characters or symbols. 

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is

checked, set the date and time to send the mail.

DAY OF THE WEEK
Specify the day of the week to send the periodical mails.
TIME
Specify the time of the day to send the periodical mails.

Caution

•  Do not turn off the main power when you set to send the

periodical mails.

•  Specify the correct date and time. (See page 25.)  

If the date and time settings are incorrect, the periodical 

mail is not sent properly.

•  Regularly confirm that the specified date and time is

correct.

•  When LOW POWER is selected for STANDBY MODE,

periodical mails will not be sent in standby mode.

51

E

51

You can configure settings related to SNMP.

SNMP SETTING
Set whether to enable or disable SNMP.
VERSION
Set the version of the SNMP to be supported.
COMMUNITY NAME 1 to 3
Set the name of the community required for the access.
USER 1 to 3
Set the user name, password, authentication method and 

other options required for access.
TRAP SETTING
Set whether to enable or disable the trap function.

When this function is enabled, a trap will be sent when the

monitor is turned on.
TRAP SETTING OF AUTHENTICATION ERROR
Set whether the trap function sends a notification when

authentication fails.
TRAP ADDRESS & PORT
Set the destination address and port number of the 

notification sent by the trap function.

Caution

•  After you set SNMP, click [Switch the main power of

monitor off and on now.] or turn off the monitor and then

turn it on again with the main power switch. When the

monitor restarts, wait about 30 seconds and then start the

next operation.

•  If the IP address is changed while the SNMP function is

operational, turn off the monitor and then turn it on again 

with the main power switch.

TIPS

•  Depending on the SNMP settings, a short delay may occur

before the SNMP is usable. (About 2 minutes)

•  Up to 16 alphanumeric letters and symbols can be used for

the community name, user name and password.

You can display a specific URL in the URL INFORMATION

field on the INFORMATION screen when an error occurs in

the monitor. (See page 47.)

URL INFORMATION
Enter the URL to display on the INFORMATION screen when

an error occurs on the monitor.

Up to 64 alphanumeric characters or symbols can be used.
CONDITION
Specify the condition to display the URL.
CONFIRMATION
The home page of the specified URL is displayed.

You can check whether the URL you entered is correct.

TIPS

•  It is also possible to specify the message text, such as the

name of a contact or a telephone number, to be displayed 

instead of the linked URL.

52

E

If you are experiencing any problem with your display, before 

calling for service, please review the following troubleshooting 

tips.
There is no picture or sound.

•  Is the power cord disconnected? (See page 16.)

•  Is the main power switch off? (See page 18.)

•  Is the monitor in standby mode (the power LED illuminating

in orange)?

•  Make sure correct input mode is selected. (See page 19.)

•  If any external equipment is connected, make sure the

equipment is operating (playing back).

•  Are the batteries inserted with polarity (+,-) aligned? (See

page 15.)

•  Are the batteries exhausted?

•  Point the remote control unit toward the remote control

sensor.

•  When the PN-ZR01 (optional) is connected, is REMOTE

CONTROL SENSOR under CONTROL KIT SETTING on

the SETUP menu set to INTERNAL? (See page 24.)

•  Is the menu display hidden or is operation disabled? (See

page 30.)

•  Is the PN-ZR01 (optional) remote control sensor box

disconnected?

•  Are audio cables connected properly? (See pages 12 to

13.)

•  Make sure audio cables for external speakers are

connected properly: left and right cables may be reversed 

or one of the two cables may not be connected. (See page

13.)

•  Check the setting of BALANCE for AUDIO menu. (See

page 23.)

•  Is the sound muted?

•  Make sure the volume is not set to minimum.

•  Are audio cables connected properly?

•  Is the setting of AUDIO SELECT on the OPTION menu

correct? (See page 25.)

•  The signal may be incompatible.

•  Try the automatic screen adjustment when the PC D-sub

input terminal or PC RGB input terminals are used.

•  Is the setting for HDMI of INPUT SELECT on the OPTION

menu correct? (See page 25.)

•  Is the HDMI cable HDMI standard compliant? The monitor

will not work with cables that are not standard compliant.

•  Is the input signal compatible with this monitor? (See pages

56 to 57.)

•  Is the setting for DVI of INPUT SELECT on the OPTION

menu correct? (See page 25.)

•  Is the input signal compatible with this monitor? (See pages

56 to 57.)

•  Turn off the power to the connected equipment and then

turn the power on again.

•  If the monitors are connected in a daisy chain, turn off the

power to all the monitors connected in a daisy chain and 

then turn the power on again.

•  Is the setting for BNC or D-SUB of INPUT SELECT on the

OPTION menu correct? (See page 25.)

•  Is the input signal compatible with this monitor? (See pages

56 to 57.)

•  Load noises from outside may be interfering with normal

operation. Turn off the power and turn it on after waiting at 

least 5 seconds, and then check the operation.

•  When the AUTO INPUT CHANGE is ON and no signal

is present in a selected input mode, the AUTO INPUT 

CHANGE automatically changes the selected mode to a

mode where a video signal is present.

  The input mode may change in the following cases:

- When a computer is in standby mode.

- When video play is stopped with a playback device.

•  Hardware has a problem. Turn off the monitor and request

repair from your SHARP dealer. 

(When STATUS ALERT is set to OSD & LED. This varies

depending on the setting.)

•  When the internal temperature of the monitor rises

excessively, the brightness of the backlight automatically 

decreases in order to prevent a further temperature rise. If 
you attempt to use 

 

to adjust the brightness while

the monitor is in this state, “AUTO DIMMING” is displayed

and you cannot change the brightness.

•  Remove the cause of the excessive temperature rise.

•  You may occasionally hear a cracking sound from the

monitor. This happens when the cabinet slightly expands 

and contracts according to change in temperature. This 

does not affect the monitor’s performance.