DOWNLOAD Sharp LL-T19D1 Service Manual ↓ Size: 1.87 MB | Pages: 26 in PDF or view online for FREE

LL-T19D1

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS

2 – 1

Caution:

•  When connecting, ensure that both the monitor and computer are switched off.

•  Be careful not to overly bend the cable or add extension cords as this could lead to a malfunction.

■

Connect the analog signal cable to the analog RGB output terminal of

the computer.

• For analog connection, use the analog signal cable accessory or a

commercially available one (both ends should be mini D-sub15 pin).

• Paying attention to connector direction, firmly insert the signal cable

vertically into the connector, and then tighten the screws at both

sides.

If connecting to a D-sub 15 pin 2 row Apple Power Macintosh, attach a
Macintosh conversion adapter (commercially available) to the analog

signal cable.

Note: If connecting to the Sun Ultra series, a conversion adapter (com-

mercially available) may be required.

■

Connect the separately-sold digital signal cable (NL-C01E) to the digital
RGB output terminal of the computer.

• The monitor has an input for connecting to a computer with a DVI-

compatible output connector (DVI-D24 pin or DVI-I29 pin) and SXGA

output capability. (Depending on the type of computer to be con-

nected, the display may not work correctly.)

• Paying attention to connector direction, firmly insert the signal cable

vertically into the connector, and then tighten the screws at both
sides.

Analog RGB output terminal

Analog signal cable

Analog RGB input terminal 1 and 2
You can connect to either side.

Macintosh conversion adapter

DVI-D input terminal

Digital RGB output terminal

Digital signal cable

Power cord

Power terminal

AC outlet

LL-T19D1

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS

2 – 2

1.

Turn on the main power of the monitor.

•  When switching the main power switch on and off, always wait for an

interval of at least 5 seconds. Rapid switching may result in malfunc-

tion.

2.

Press the monitor's POWER button.
The power LED will light up orange.

3.

Turn on the computer.

When a signal is input from the computer, the power LED lights up
green, and the screen is displayed. (After power is turned on, it may

take a little time until the screen is displayed.)

•  If the input terminal to which the computer is connected has not

been selected, the screen will not be displayed. If necessary, per-
form input terminal switching.

Notes:

• When using an analog signal, perform an automatic screen adjust-

ment under the following conditions:

– Using the monitor for the first time.

– After having changed the system settings during use.

• Depending on the computer or OS, it may be necessary to use the

computer to install monitor set-up information.

•  When connecting to a notebook, if the notebook computer's screen is

set so that it is displaying at the same time, the MS-DOS screen may

not be able to display properly. In this case, change the settings so

that only the monitor is displaying.

Use the INPUT button to switch between signal input terminals.

1. Turn the computer off.

2. Press the monitor's POWER button.

The Power LED will disappear.

If the monitor will not be used for a long time, turn off the main power

switch of the monitor, and remove the power plug from the outlet.

Main power switch

Press power button.

Turn on the computer 

power supply.

ON

Analog RGB input terminal 1

Analog RGB input terminal 2

DVI-D input terminal

INPUT

INPUT

INPUT

INPUT-1 ANALOG

INPUT-2 ANALOG

INPUT-3 DIGITAL

Press power button.

Turn the computer 

off.

OFF

LL-T19D1

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS

2 – 3

An arm or stand based on the VESA standard (commercially available)

can be attached to the monitor.
Procurement of the arm or stand is at the customer's discretion.

Attachments must satisfy the following.

•  Compatible with the VESA standard

• Have a gap of 100 mm x 100 mm between the screw holes on the

section to be attached

•  Not be likely to fall off or break off after being attached to the monitor.

•  Be careful not to overly bend the cable or add extension cords as this

could lead to malfunction.

•  While following these instructions, please also refer to the installation

instructions in the operation manual included with the arm or stand.

Caution: Be careful not to get your fingers pinched between the display

and stand nor to let the stand drop. These could lead to injury.

1.

Remove the cables.

2.

Spread out a soft cloth on a suitable horizontal surface.

3.

Being careful not to damage the monitor, gently lay the monitor on it

display-side down.

4.

Remove the cover.

• While pressing the 

A

 areas on the sides, push it up.

5. Remove the six screws and then remove the stand from the moni-

tor.

Note:

•  The stand is specially made for use with this monitor. Once having

removed the stand, never attempt to attach it to another device.

•  Once having removed the screws, store them together with the

stand and if the stand is ever re-attached be sure to use the original

screws.

Using different screws could lead to a malfunction.

6. Attach the arm to the monitor with the four screws.

Note: The screws used to attach the arm should be M4 screws with a

length of 6 mm ~ 8 mm protruding from the surface to be
attached.

Using different screws could cause the monitor to fall off or to be

internally damaged.

6 - 8 mm

Screw used to attach arm

Arm

Part of monitor to which arm is attached

LL-T19D1

CONNECTION, ADJUSTMENT, OPERATION, AND FUNCTIONS

2 – 4

7) Version display (for service)

While pressing

, turn on

the power.

•  Valid even when there is no input signal.

•  The Model name version, the date, H-SYNC, V-SYNC and check

sum are displayed.

•  When

is pressed, the version display disappears.

• All the keys except for

and the power key are dis-

abled.

•  The version display keeps ON until

or the power key

is pressed.

6) Aging (for service)

While pressing

, turn on

the power.

•  When the selftest is executed, no menu is shown.

•  When the selftest is executed, the display shows Red 

3

 Green

3

 Blue 

3

 Yellow 

3

 Purple 

3

 Light Blue 

3

 White 

3

 Black

repeatedly.

•  When the selftest is executed, all the keys except for the power

key are disabled.

•  Turn off the power to terminate the selftest.

•  When the signal is inputted, the screen inputted is displayed and

it does not entry into aging mode.

MENU

MENU

MENU

4)   Adjusting the backlight

buttons

5)   Setting display mode

button (STD, OFFICE, sRGB, VIVID)

1)   Resetting all adjustment values

Power ON

Power ON

Press the above two buttons at same time, and while turn the power on.

2)   ADJUSTMENT menu reset

Press the two buttons at same time.

3)   Adjustment lock function

6)  Screen adjustment

MENU

ADJUSTMENT
(Analog)

(Analog)

(Analog)

AUTO

CLOCK

PHASE

H-POS

V-POS

AUTO

MENU

GAIN CONTROL

BLACK LEVEL

CONTRAST

MENU

(COOL      STD   

WHITE BALANCE

  WARM    USER)

R-CONTRAST

CONTRAST
(R/G/B)

G-CONTRAST

B-CONTRAST

MENU

MODE SELECT

MENU

MENU

buttons

buttons

buttons

buttons

buttons

buttons

buttons

buttons

buttons

buttons

OSD H-POSITION

OSD V-POSITION

SCALING

buttons

buttons

buttons

LANGUAGE

buttons

END

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

/MODE

400 LINES

buttons

/MODE

/MODE

Valid even when there is no input signal.
When the above procedure is executed, key lock/release is changed over.
When key lock is set, the black display is shown and "ADJUSTMENT LOCKED" is displayed for about 2 sec.
When key release is set, the black display is shown and "ADJUSTMENT UNLOCKED" is displayed for about 2 sec.
When key lock is set, all the keys except for the power key are disabled.

e

d

c

 /MODE

MODEL NAME  :  LL-T19D1

VERSION : 

1.000

DATE : 

2/07/2003

CHECK SUM 

:  xxxx

H-SYNC. : 

X 

Hz

V-SYNC. : 

X 

kHz

MENU

MENU

MENU

c

 /MODE

e

MENU