DOWNLOAD Sharp LL-T17D3 (serv.man13) Service Manual ↓ Size: 1.6 MB | Pages: 127 in PDF or view online for FREE

Adjustments can be made using On Screen
Display (OSD) Menu provided.

If you are using Windows, open the Adjustment
Pattern on the accompanying Utility Disk. (p. 16)
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image
that makes the entire screen light and adjust it
through checking visually its actual tone.
This chapter provides the procedure how to adjust
the screen by using Adjustment Pattern (for
Windows)

1.Press the MENU button.

The ADJUSTMENT Menu will be displayed.

A D J U S T ME N T

           MANU A L                         A U T O

C L OC K                                       1 2 7

P H A S E                                           1 6

H- P O S                                       2 0 0

V - P O S                                           2 9

I N P U T - 1

A N A L O G

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

At this point relevant menu options can be
adjusted.
Each time the MENU button is pressed the next
menu is selected. (ADJUSTMENT 

→ GAIN

CONTROL 

→ WHITE BALANCE→ MODE

SELECT 

→ OSD Menu disappears)

Note:
- The OSD Menu automatically disappears

approximately 30 seconds after the last
command.

A D J U S T ME N T

           MANU A L                         A U T O

C L OC K                                       1 2 7

P H A S E                                           1 6

H- P O S                                       2 0 0

V - P O S                                           2 9

I N P U T - 1

A N A L O G

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

MANUAL: Individual menu options are manually

adjusted.

AUTO:

Every menu option is automatically
adjusted.

- Press the   button to select [AUTO].
- To choose a menu option: 

 / MODE button

- To go to the next menu: MENU button

CLOCK
The figure below demonstrates how to adjust so
that vertical flicker noise is not emitted. (  
buttons)

PHASE
The figure below demonstrates how to adjust so
that horizontal flicker noise is not emitted. (  
buttons)
Note:
- Adjustments to PHASE should be made only

after CLOCK has been correctly set.

H-POS (horizontal positioning) and V-POS
(vertical positioning)
To center the adjustment pattern within the
boundaries of the screen, adjust the left-right (H-

POS) values and the up-down (V-POS) values. (

 buttons)

Vertical flicker noise

Horizontal flicker noise

Screen frame

Adjustment

pattern

02_LL-T17D3_gb.p65

11/29/2002, 5:14 PM

17

WH I T E   B A L A N C E

C OOL

 

S TD

 

WA R M

 

U S E R

R- CONTRAST

G- CONTRAST

B - CONTRAST

I N P U T - 1

A N A L O G

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

Notes:
- On settings other than [STD] not all gradations

can be displayed. To display all gradations, set to
[STD].

- If [COLOR MODE] is set to [sRGB] or [VIVID], no

other setting than [STD] can be selected.

- Use the     buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting [USER] will display the setting values

for [R-CONTRAST], [G-CONTRAST] and [B-
CONTRAST], in order to make fine adjustments.

- Use the 

 / MODE button to select

[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- To go to the next menu: MENU button

COOL ....... Color tone bluer than standard
   • ............. Color tone slightly bluer than standard
STD .......... Color tone standard setting
   • ............. Color tone slightly redder than standard
WARM ...... Color tone redder than standard

R-CONTRAST .....

  button for blue-green
  button for red

G-CONTRAST .....

  button for purple
  button for green

B-CONTRAST .....

  button for yellow
  button for blue

G A I N   C ON T R O L

                        MANU A L                       A U T O

B L AC K  L E V E L                   3 2

CON T R A S T                               8 0

I N P U T - 1

A N A L O G

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

MANUAL: Individual menu options are manually

adjusted.

AUTO:

Every menu option is automatically
adjusted using the Auto Gain Control*
function.

- Press the   button to select [AUTO].
- To choose a menu option: 

 / MODE button

- To go to the next menu: MENU button

* Auto Gain Control function
- The Auto Gain Control adjusts contrast and black

level based on the brightest and darkest colors of
the image displayed. If you are not using the
Adjustment Pattern it is necessary to have black
area and white area of at least 5 mm x 5 mm on
the screen. Adjustment may not be possible
without those areas.

- If the signal coming from the computer is

composite sync or sync on green, automatic
adjustment cannot be performed. Please perform
manual adjustment instead.

- If [OUT OF ADJUST] is displayed, perform

manual adjustment.

- When using the Auto Gain Control function, set

[WHITE BALANCE] to other than [USER]. If
[USER] is set, the Auto Gain Control function
cannot be used.

BLACK LEVEL
Total screen brightness can be adjusted while

watching the color pattern. (    buttons)

CONTRAST
While watching the color pattern, adjustments can
be made so that all gradations appear. (    but-
tons)

Color pattern

02_LL-T17D3_gb.p65

11/29/2002, 5:14 PM

18

M O D E   S E L E C T

O S D

 

H - POS I T I ON

O S D

 

V - POS I T I ON

S C A L I NG                                     3

I N P U T

V E S A

M A C

4 0 0

 

L I NE S

6 4 0

7 2 0

L A NGU A G E

I N P U T - 1

A N A L O G

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

Notes:
- Depending on the resolution of the input signal,

even if menu options can be selected, the display
may not change.

- To choose a menu option: 

 / MODE button

- To complete adjustment: MENU button

OSD H-POSITION (OSD horizontal position)
The position of the OSD Menu can be moved to the

left and right. (    buttons)

OSD V-POSITION (OSD vertical position)
The position of the OSD Menu can be moved up
and down. (    buttons)

The sharpness of the image can be adjusted.  (  
buttons)
Note:
- When the display mode is set to less than

1280 x 1024 pixels, the display is enlarged to
cover the whole screen (i.e. the side ratio of the
display may change).

INPUT
When connecting a Power Macintosh, set to [MAC].
(    buttons)

400 LINES (degree of resolution)
You can specify the horizontal resolution of a 400-

line screen when using US text, etc. (    buttons)

640: 640 X 400 dot mode
720: 720 X 400 dot mode (US text etc.)

Note:
- As the resolution input for other than 400 lines is

done automatically, there is no need to set it.

LANGUAGE
You can choose the language used in OSD Menu.
1. Press the   button.

The Language Selection Menu will be displayed
on the screen.

2. Use the 

 / MODE button to choose a language.

3. Press the MENU button.

Language Selection Menu will disappear.

02_LL-T17D3_gb.p65

11/29/2002, 5:14 PM

19

Adjustments can be made using On Screen
Display (OSD) Menu provided.

If you are using Windows, open the Adjustment
Pattern on the accompanying Utility Disk. (p. 16)
If your system is not Windows, you can not use the
Adjustment Pattern. Therefore display an image
that makes the entire screen light and adjust it
through checking visually its actual tone.
This chapter provides the procedure how to adjust
the screen by using Adjustment Pattern (for
Windows)

1.Press the MENU button.

The WHITE BALANCE Menu will be displayed.

WH I T E   B A L A N C E

C OOL

 

S TD

 

WA R M

 

U S E R

R- CONTRAST

G- CONTRAST

B - CONTRAST

I N P U T - 2

D I G I T A L

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

At this point relevant menu options can be
adjusted.
Each time the MENU button is pressed the next
menu is selected. (WHITE BALANCE 

→ MODE

SELECT 

→ OSD Menu disappears)

Notes:
- The OSD Menu automatically disappears

approximately 30 seconds after the last
command.

WH I T E   B A L A N C E

C OOL

 

S TD

 

WA R M

 

U S E R

R- CONTRAST

G- CONTRAST

B - CONTRAST

I N P U T - 2

D I G I T A L

1 2 8 0 x 1 0 2 4

V : 6 0 H z       H : 6 4 . 0 k H z

Notes:
- On settings other than [STD] not all gradations

can be displayed. To display all gradations, set to
[STD].

- If [COLOR MODE] is set to [sRGB] or [VIVID], no

other setting than [STD] can be selected.

- Use the     buttons to select [COOL], [·], [STD],

[·], [WARM] or [USER].

- Selecting [USER] will display the setting values

for [R-CONTRAST], [G-CONTRAST] and [B-
CONTRAST], in order to make fine adjustments.

- Use the 

 / MODE button to select

[R-CONTRAST], [G-CONTRAST] and
[B-CONTRAST].

- To go to the next menu: MENU button

COOL ....... Color tone bluer than standard
   • ............. Color tone slightly bluer than standard
STD .......... Color tone standard setting
   • ............. Color tone slightly redder than standard
WARM ...... Color tone redder than standard

R-CONTRAST .....

  button for blue-green
  button for red

G-CONTRAST .....

  button for purple
  button for green

B-CONTRAST .....

  button for yellow
  button for blue

02_LL-T17D3_gb.p65

11/29/2002, 5:14 PM

20