DOWNLOAD Sharp LL-T15G3 (serv.man17) Service Manual ↓ Size: 6.74 MB | Pages: 116 in PDF or view online for FREE

LCD display

38 cm measured diagonally
TFT LCD module

Resolution (max.)

XGA 1024 x 768 pixels

Displayable colors (max.)

Approx.16.19 million colors (6bit + FRC)

Brightness (max.)

260cd/m

2

Dot pitch

0.297(H) x 0.297(V) mm

Contrast ratio

350:1

Angle of visibility

Left-right 160°; Up-down 150°
(contrast ratio 

>

=

 5)

Screen display size

Horizontal 304.1 mm x Vertical 228.1 mm

Video signal

Analog RGB (0.7Vp-p) [75

Ω]

Sync signal

Separate Sync (TTL level: +/-), Sync on
Green, Composite Sync (TTL level: +/-)

Expansion compensation

Digital screening (Enlargement VGA/SVGA etc.
to full screen size.)

Plug & Play

VESA DDC1/DDC2B compatible

Power management

VESA: based on DPMS

Input signal terminal

Mini D-sub 15 pin (3 row)

Screen tilt

Upward approx.0 - 25°; downward approx.0 - 5°

Power supply

AC100 - 240V, 50/60Hz

Temperature of operating environment

5 - 35°C

Power consumption

Maximum 33W (Standby state: 2W)

Dimensions

338(W) x 145(D) x 313(H) mm

Weight

Approx. 3.8kg (approx. 3.2kg excluding stand)
(Excluding analog signal cable.)

(Units: mm)

338

63

275

313

203

145

Analog signal cable: Approx. 1.8m

02_LL-T15G3_gb.p65

10/28/2002, 9:04 AM

21

(Mini D-sub connector with 15 pins)

5

1

2

3

4

10

6

7

8

9

15

11

12

13

14

No.

Function

1

Red video signal input

2

Green video signal input

3

Blue video signal input

4

GND

5

GND

6

For red video signal GND

7

For green video signal GND

8

For blue video signal GND

9

+5V

10

GND

11

N.C.

12

DDC data

13

For Hsync signal input

14

For Vsync signal input

15

DDC clock

640x480

800x600

1024x768

720x400
640x480
832x624

1024x768

31.5kHz
37.9kHz
37.5kHz
35.1kHz
37.9kHz
48.1kHz
46.9kHz
48.4kHz
56.5kHz
60.0kHz
31.5kHz
35.0kHz
49.7kHz
60.2kHz

60Hz
72Hz
75Hz
56Hz
60Hz
72Hz
75Hz
60Hz
70Hz
75Hz
70Hz

66.7Hz
74.6Hz

75Hz

25.175MHz

31.5MHz
31.5MHz
36.0MHz
40.0MHz
50.0MHz
49.5MHz
65.0MHz
75.0MHz

78.75MHz

28.3MHz
30.2MHz
57.3MHz
80.0MHz

- Recommended resolution is 1024 x 768.
- All are compliant only with non-interlaced.
- Frequencies for Power Macintosh are reference

values.

- If the monitor is receiving timing signals that are

not compatible, [OUT OF TIMING] will appear.
Follow your computer’s instruction manual to set
the timing so that it is compatible with the
monitor.

- If the monitor is not receiving any signal (synch

signal), [NO SIGNAL] will appear.

The monitor is based on VESA DPMS (Display
Power Management Signaling).
To activate the monitor's Power Management
function, both the video card and the computer
must conform to the VESA DPMS standard.

This monitor supports the VESA DDC (Display
Data Channel) standard.
DDC is a signal standard for carrying out Plug &
Play functions on the monitor or PC. It transfers
information such as degree of resolution between
the monitor and PC. You can use this function if
your PC is DDC compliant and if it is set so that it
can detect the Plug & Play monitor.
There are many varieties of DDC due to the
differences between systems. This monitor works
with DDC1 and DDC2B.

DPMS mode

Screen

Power

H-sync V-sync

consumption

ON

Display on

33W

Yes

Yes

STANDBY

No

Yes

SUSPEND

Display off

2W

Yes

No

OFF

No

No

02_LL-T15G3_gb.p65

10/28/2002, 9:04 AM

22

6. Attach the arm to the monitor with four screws.

Note:
- The screws used to attach the arm should be M4

screws with a length of 8 mm ~ 10 mm protruding
from the surface to be attached. Using different
screws could lead to malfunction or may lead to
the monitor falling off,internal damaged,personal
injury.

8 - 10mm

7.Connect the analog signal cable and power cord.

An arm or stand based on the VESA standard
(commercially available) can be attached to the
monitor.
Procurement of the arm or stand is at the custom-
er's discretion.

When choosing the arm to be installed please take
note of the following points.
- The arm should be compatible with the VESA

standard, and there must be a gap of 75mm x
75mm between the screw holes on the section to
be attached.

- The arm must not fall off or break off after being

attached to the monitor.

1. Ensure that both the monitor and computer are

switched off.

2.Unplug the power cord from the AC outlet.
3.Remove the analog signal cable from the

computer.

4. Press down on the stand and gently fold back the

monitor.

- Do not overly bend the cable or add extension

cords as this could lead to malfunction.

5. Being careful not to damage the monitor, spread

out a soft cloth and lay the monitor on it display-
side down.

Screw used to attach arm

Arm

Part of monitor to which arm is
attached

02_LL-T15G3_gb.p65

10/28/2002, 9:04 AM

23

The stand may be removed.

1.Turn off the monitor, and remove the analog

signal cable and the power cord from the
monitor.

2. Being careful not to damage the monitor, spread

out a soft cloth and lay the monitor on it display-
side down.

3. Remove the four screws and then remove the

stand from the monitor.

- The stand is specially made for use with this

monitor. Once having removed the stand, never
attempt to attach it to another device.

- Once having removed the screws, store them

together with the stand and if the stand is ever
re-attached be sure to use the original screws.
Using different screws could lead to a
malfunction.

4.Follow instruction no.6 on page 23 to attach the

arm to the monitor, then connect the analog
signal cable and the power cord.

02_LL-T15G3_gb.p65

10/28/2002, 9:04 AM

24