DOWNLOAD Sharp LL-172AW (serv.man2) Service Manual ↓ Size: 1.21 MB | Pages: 36 in PDF or view online for FREE

- Be sure to hold both sides of the monitor when

adjusting the viewing angle. The LCD panel
used in this monitor is made of glass. Pressure
from hands on the LCD panel could cause
damage.

- Be careful not to allow your fingers to be

pinched.

1. Release the lock.
2. Adjust the height of the stand.
3. Set the lock.

2

3

1

- Be sure to release the lock before adjusting the

height of the stand. Extending/contracting the
stand when it's locked may result in damage to
the product.

- Ensure that the stand is properly locked except

while adjusting the height.

approx. 70 mm

approx. 45°

approx. 45°

approx. 25°

approx. 5°

[LL-172A]

approx. 25°

approx. 5°

[LL-172G]

172AG_gb.PMD

3/24/2004, 11:44 AM

13

- When connecting, ensure that both the monitor

and computer are switched off.

- Be careful not to over bend the cable or add

extension cords as this could lead to a
malfunction.

Use the supplied cable clamps to secure the
cables connected to the terminals.
The upper and lower cable clamps have different
shapes. Check the shapes of the clamps before
attaching them to the stand.

- When adjusting the viewing angle, cables may

be pulled. Therefore, ensure that the cables
have sufficient slack.

Connect the accessory analog signal cable to the
analog RGB output terminal of the computer.

- Paying attention to connector direction, firmly

insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.

Analog signal cable

Analog RGB terminal
(Mini D-sub 15 pin, 3 row)

Orient the side of the clamp
with the protrusion to the
stand and attach the clamp.

172AG_gb.PMD

3/24/2004, 11:44 AM

14

Connect the accessory digital signal cable to the
digital RGB output terminal of the computer.
- The monitor has an input for connecting to a

computer with a DVI-compatible output
connector (DVI-D 24 pin or DVI-I 29 pin) and
SXGA output capability. (Depending on the type
of computer to be connected, the display may
not work correctly.)

- Paying attention to connector direction, firmly

insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.

Set the monitor as follows when establishing a
digital connection with a Power Mac using an ADC-
DVI adapter made by Belkin. (Operation has been
checked with the Power Mac G4 M7627J/A.)
- Perform settings with the Power Mac power

supply off.

1. After connecting the power cord, turn on the

monitor's main power.

2. Press the   button and   button simultaneously,

and while doing this press the power button (i.e.
turn the power on).

O K         [ M E N U ]

MAC DIGITAL

INPUT-2

OFF

ON

3. Set to [ON] with the     buttons.

- Do not set to [ON] if you are not using a Belkin

ADC-DVI adapter, as this may result in
incorrect display.

4. Press the MENU button.

This completes setting.

Connect the accessory analog signal cable, or
separately-sold analog signal cable (model name:
NL-C02E) to the analog RGB output terminal of
the computer.
- Connect the accessory analog signal cable to

the analog RGB input terminal (INPUT-1).

- Connect the separately-sold analog signal cable

(model name: NL-C02E) to the DVI-I input
terminal (INPUT-2).

- Paying attention to connector direction, firmly

insert the signal cable vertically into the
connector, and then tighten the screws at both
sides.

If connecting to a D-sub 15 pin 2 row Apple Power
Macintosh, attach a Macintosh conversion adapter
(commercially available) to the analog signal
cable.

Note:
- If connecting to the Sun Ultra series, a

conversion adapter (commercially available)
may be required.

Macintosh conversion adapter

Analog signal cable

Analog RGB output
terminal

DVI-I input terminal
(INPUT-2)

Analog RGB
input terminal
(INPUT-1)

Digital signal cable

Digital RGB output terminal

DVI-I input terminal
(INPUT-2)

172AG_gb.PMD

3/24/2004, 11:44 AM

15

The separately sold 2-input cable (model name:
NL-C03J) enables connection between the DVI-I
input terminal on the monitor and the two
computers. (One analog and one digital
connection.)

1. Connect the 2-input cable to the DVI-I input

terminal of the monitor.

2. Connect the accessory or commercially

available analog signal cable and the accessory
digital signal cable to the 2-input cable.
- When using commercially available analog

signal cable, both ends should be mini D-sub
15 pin.

3. Connect each signal cable to the computers.

- Paying attention to connector direction, firmly

insert the signal cable into the connector, and
then tighten the screws at both sides.

Digital RGB
output terminal

Digital signal cable

2-input cable
(purchased
separately)

Mini D-sub 15 pin

DVI-D 24 pin

Analog RGB
output terminal

Analog signal
cable

DVI-I input terminal

(INPUT-2)

Notes:
- When using the 2-input cable, set the

connecting input terminal [INPUT-2] to [2LINES]
under the MODE SELECT-2 Menu. (p.24)

- The monitor connected to the 2-input cable by

analog connection may not be automatically
recognized and setup under Plug & Play.
Perform storage of setup information manually.
(p.31)

When the accessory audio cable is connected to
the audio output terminal of the computer, the
sound of the connected computer is output from
the monitor speakers. You can also use the
headphone jack of the display.

Audio output terminal

Audio cable

Audio input terminal

172AG_gb.PMD

3/24/2004, 11:44 AM

16