Sharp LB-1085 (serv.man3) User Manual / Operation Manual ▷ View online
15
Preparation
When using DVI Cable (INPUT 7):
DVI cable
(commercially available)
Ø 3.5 mm stereo minijack cable
(commercially available)
Blu-ray disc player/DVD player
To enjoy 1080p display capability, connect your external equipment using a component or DVI cable and set the
•
equipment to 1080p output.
Using Digital Audio Output
It is possible to output audio through the DIGITAL AUDIO OUTPUT terminal. PCM audio outputs from the
terminal.
terminal.
To optical digital input of
external audio devices
Optical fi ber cable
(commercially available)
Depending on the connected equipment, audio will not output from the DIGITAL AUDIO OUTPUT terminal in HDMI
•
connection. In this case, set the audio formats of the connected equipment to PCM, 32/44.1/48 kHz.
Connecting HDMI Equipment
You can use the INPUT 4, INPUT 5 or INPUT 6 terminal when connecting HDMI equipment.
HDMI equipment
HDMI-certifi ed cable*
(commercially available)
When using an HDMI-DVI conversion cable, input the audio signal to the AUDIO terminal of INPUT 6.
•
To enjoy 1080p display capability, connect your Blu-ray disc player or other external equipment using an HDMI-
•
certifi ed cable and set the equipment to 1080p output.
Use a commercially-available HDMI cable complying with HDMI standards. Using a non-standard cable will not
*
function normally, resulting in video not being shown or sound not being produced.
Set the player not to use the HDMI CEC function such as AQUOS LINK. Using the HDMI CEC function may cause
*
malfunction.
16
Connecting a PC
When connecting to a PC with a DVI terminal (INPUT 7):
PC
Ø 3.5 mm stereo minijack cable
(commercially available)
RGB/DVI conversion cable
(commercially available)
When connecting to a PC with an HDMI terminal (INPUT 4, 5 or 6):
HDMI-certifi ed cable
(commercially available)
PC
The HDMI terminals only support digital signal.
•
If you are connecting the LCD Monitor to a PC with a DVI terminal, use a DVI cable (commercially available) instead
•
of a RGB/DVI conversion cable.
PC Compatibility Chart
It is necessary to set the PC correctly to display XGA and WXGA signal. Refer to page 26 to set PC input
signals.
signals.
PC
31.5 kHz
31.5 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
37.9 kHz
37.5 kHz
35.1 kHz
37.9 kHz
48.1 kHz
46.9 kHz
48.4 kHz
56.5 kHz
60.0 kHz
47.7 kHz
640 x 480
720 x 400
VGA
800 x 600
SVGA
XGA
1024 x 768
WXGA
1360 x 768
70 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
72 Hz
75 Hz
56 Hz
60 Hz
72 Hz
75 Hz
60 Hz
70 Hz
75 Hz
60 Hz
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
64.0 kHz
SXGA
1280 x 1024
60 Hz
O
65.3 kHz
SXGA+
1400 x 1050
60 Hz
O
37.5 kHz
720p
50 Hz
45.0 kHz
60 Hz
28.1 kHz
1080i
50 Hz
33.8 kHz
60 Hz
56.3 kHz
1080p
1280 x 720
1920 x 1080
1920 x 1080
50 Hz
67.5 kHz
60 Hz
75.0 kHz
UXGA
1600 x 1200
60 Hz
O
PC
Horizontal Frequency
VESA Standard
Resolution
Vertical Frequency
DDC is a registered trademark of Video Electronics Standards Association.
VGA and XGA are registered trademarks of International Business Machines Corp.
VGA and XGA are registered trademarks of International Business Machines Corp.
Preparation
17
Turning On/Off the Power
Press POWER on the LCD Monitor, or POWER on the remote
control unit to turn the power on.
control unit to turn the power on.
POWER indicator (Blue): The LCD Monitor is on. (After a few seconds,
•
a window appears with sound.)
The initial setup starts when the LCD Monitor powers on for the fi rst
•
time. If the LCD Monitor has been turned on before, the initial setup will
not be invoked. For changing the settings of the initial setup, perform
EZ setup on the Setup menu on page 26.
When the main POWER is off, you cannot turn on the LCD Monitor by
not be invoked. For changing the settings of the initial setup, perform
EZ setup on the Setup menu on page 26.
When the main POWER is off, you cannot turn on the LCD Monitor by
•
pressing POWER.
Press POWER on the LCD Monitor, or POWER on the remote
control unit again to turn the power off.
control unit again to turn the power off.
The LCD Monitor enters standby and the image on the screen
•
disappears.
The POWER indicator on the LCD Monitor turns off.
The POWER indicator on the LCD Monitor turns off.
•
If you ar
•
e not going to use this LCD Monitor for a long period of time, be
sure to remove the AC cord from the AC outlet.
Weak electric power is still consumed even when the LCD Monitor is in
Weak electric power is still consumed even when the LCD Monitor is in
•
standby mode.
Initial Setup
POWER
POWER
(On/Standby)
Language (Language setting)
1
Press / to select the desired language
listed on the screen, and then press ENTER.
Language
Monitor Location
English
Español
Deutsch
Français
Monitor Location
Select “Home” or “Store” for the location where you
plan to install the LCD Monitor.
Select “Home” or “Store” for the location where you
plan to install the LCD Monitor.
2
Press / to select “Home” or “Store”.
Press ENTER to enter the setting.
Example
Monitor Location
Language
Home
Store
If you select “Home”, AV MODE is set to “STANDARD”.
•
If you select “Store”, AV MODE is set to
•
“DYNAMIC (Fixed)”.
If there is no operation for 30 minutes, AV MODE will
return to “DYNAMIC (Fixed)” automatically, regardless
of previous changes to the AV MODE settings.
For changing the Monitor Location after the setting,
If there is no operation for 30 minutes, AV MODE will
return to “DYNAMIC (Fixed)” automatically, regardless
of previous changes to the AV MODE settings.
For changing the Monitor Location after the setting,
•
see “EZ Setup” on page 26.
When you turn on the LCD Monitor for the fi rst time,
initial setup menu screen will appear. Set desired
“Language” and “Monitor Location”.
initial setup menu screen will appear. Set desired
“Language” and “Monitor Location”.
18
Direct Button Operation
Changing Volume
You can change the volume by pressing VOL /
on the LCD Monitor or on the remote control unit.
on the LCD Monitor or on the remote control unit.
To increase the volume, press
•
VOL .
To decrease the volume, press
•
VOL .
20
Audio status
Output device
Output Select
Fixed
Variable
Speaker
Variable sound
Mute
When “Output Select” is set to “Variable”, the indicator
•
on the screen changes as shown below.
60
See page 28 for details on the Output Select function.
•
MUTE
Mutes the current sound output.
Press MUTE.
“
•
” will be displayed on the screen for 30 minutes,
and the sound is silenced.
Within 30 minutes of pressing
•
MUTE, mute can be
canceled by using one of the methods below.
- Mute will be canceled if you press VOL / or
MUTE.
Mute will be canceled after 30 minutes have
- Mute will be canceled if you press VOL / or
MUTE.
Mute will be canceled after 30 minutes have
•
passed. However, the LCD Monitor will not suddenly
output a loud sound as the volume level is set to 0
automatically.
output a loud sound as the volume level is set to 0
automatically.
Click on the first or last page to see other LB-1085 (serv.man3) service manuals if exist.