Sharp UP-5900 (serv.man7) Service Manual ▷ View online
UP-5900VI
MCR UNIT: UP-E12MR2
– 7 –
12. MCR UNIT: UP-E12MR2
1) Fix the MCR ANGLE
1
to the lower cabinet with two screws
2
.
2) Connect the MCR cable
3
to the MCR connector with the cable
holder
6
, and tighter the screw
7
on the back of lower cabinet.
3) Install the ferrite Core
4
to the MCR cable and GND wire
5
.
4) Fix the earth wire
5
from the UP-E12MR2 with the screw.
5) Attach the rubber foot in Main Unit.
13. Rear display UP-I20DP
1) Remove the Display filter
1
.
2) Remove the Rear cover angle
2
from the Display filter
1
a) Remove the two Screws
3
.
3) Connect the display cable
4
to the connector: CN22 on the Main
PWB.
4) Install the Display unit
5
to the cabinet
a) Align the positioning boss
A
of the bottom cabinet with the
angle hole
A
in the display unit.
14. Pole display: UP-P20DP
1) Install the core
6
to the display cable
1
and the display earth
cable
4
.
2) Connect the Display cable
1
to the remote display connector on
the back of the set.
3) Fix the display cable
1
with the cable holder
2
, and tighten the
screw
3
on the back of bottom cabinet.
4) Fix the display earth cable
4
to the main chassis with the screw
5
.
*
Cable holder
2
.
Use the following type of cable holder supplied with the UP-P20DP.
• “3N” (large type)
2
1
3
4
6
5
7
1
2
3
1
A
4
5
A
A
2
3
1
4
6
5
Within 5cm
UP-5900VI
Pole display: UP-P20DP
– 8 –
*
*
*
*
How to Extend Display Pole
The pole can be extended by installing the attached pole to the stan-
dard pole.
dard pole.
COMPONENT LIST:
1) Remove the five screws
1
.
2) Remove the Base angle
2
.
3) Remove the PWB unit
3
from the Base cabinet
4
.
4) Remove the display cable
5
from the PWB unit
3
.
5) Remove the two screws
6
.
6) Remove the Base cabinet
4
from the pole cabinet
7
.
7) Pull the Ratchet
9
attached to the pole cabinet
7
out of the Dis-
play unit
8
by turning it as shown in Figure.
8) Remove the two screws
F
.
9) Remove the pole cabinet
7
from the Ratchet
9
.
No.
NAME
USE
Q’ty
7
,
G
Pole cabinet
Pole extension
2
H
Screw (M3
u
4)
Pole connection
4
I
Screw (M4
u
16)
Securing the UP-P20DP to the
wooden table
wooden table
4
J
Screw (M4
u
20)
Securing the UP-P20DP to the
metal table
metal table
4
K
Nut
Securing the UP-P20DP to the
metal table
metal table
4
L
Display cable (S)
This display cable (S) should be
used instead of the standard
cable and earth wire if the UP-
20DP’s standard pole is
removed to lower the height of
the UP-20DP.
used instead of the standard
cable and earth wire if the UP-
20DP’s standard pole is
removed to lower the height of
the UP-20DP.
1
M
Earth wire (S)
1
Pattern side(PWB)
Core
1
2
3
4
5
1
6
4
7
7
8
9
10
10
9
UP-5900VI
Drawer unit: ER-03DW/04DW
– 9 –
10) Install the attached pole cabinet
G
to the pole cabinet
7
to fix it
with the screw
H
.
11) Install the pole cabinet
G
in the opposite order of the disassembly.
12) Fastening on the table:
Secure the Base cabinet
2
using the screw.
*
Lowering the height of the UP-P20DP
Remove the standard Pole and attach the Base cabinet
4
to the
Ratch
9
. At this time, replace the standard Display cable and the
Earth wire with the S type cable
L
and wire
M
.
15. Drawer unit: ER-03DW/04DW
1) Connect the drawer cable
1
to the drawer connector
2
.
2) Install the ferrite Core
5
to the drawer cable.
3) Fix the drawer cable
1
with the cable holder
6
, and tighten the
screw
7
on the back of lower cabinet
A
or
B
.
No.
NAME
USE
Q’ty
I
Screw (M4
u
16)
Securing the UP-P20DP to the
wooden table
wooden table
4
J
Screw (M4
u
20)
Securing the UP-P20DP to the
metal table
metal table
4
K
Nut
Securing the UP-P20DP to the
metal table
metal table
4
Display cable
7
7
11
11
12
12
12
12
2
5
1
6
7
A
B
UP-5900VI
COM1, COM2 and COM3/5 Connector
– 10 –
16. COM1, COM2 and COM3/5
Connector
1) COM1 & COM2
• D-SUB 9pin Connector
• CI signal of COM1 or COM2 and +5V power supply can be
switched in order to supply +5V power.
Connector Specifications*
D-SUB9
2) COM3/5
• Channels of COM port with an RJ45 connector are equipped.
• Two CABLE HOLDER
1
and SCREW (M3
u
8)
2
are contained in
the package.
Pin No.
Signal
Function
I/O
1
CD
Data Carrier Detect
I
2
RD
Receive Data
I
3
SD
Send Data
O
4
ER
Data Terminal Ready
O
5
SG
Signal Ground
—
6
DR
Data set Ready
I
7
RS
Request to Send
O
8
CS
Clear to Send
I
9
CI/+5V
Ring Indicate/+5V
I/–
Within 3cm
CORE(RCORF6700BHZZ)
Wire band
S2 = COM1: 1 = +5V
3 = CI
S1 = COM2: 1 = +5V
3 = CI
3
1
S1
+5V CI
3
1
S1
S1
+5V CI
3
1
S2
+5V CI
3
1
S2
S2
+5V CI
+5V
CI
COM2
COM1
2
1
Within 5cm
CORE(RCORF6700BHZZ)
Wire band
Click on the first or last page to see other UP-5900 (serv.man7) service manuals if exist.