Sharp UP-3515 Service Manual ▷ View online
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.67
Doc: up35xx_pm_e_1v68.docx
Page 29 / 43
Parts & Technical Services
>>> Changes / Improvements / Corrections since V1.67 <<<
C 7
IRC Reset after Saved Reports
C 7.1
In an Inline System an IRC Reset becomes necessary after the Saved Report has been carried out.
With this new version, an IRC Reset will be called individually at the machine after the Saved Report
is finished. This is regardless of the machine type, like Master, Backup Master or Satellite.
With this new version, an IRC Reset will be called individually at the machine after the Saved Report
is finished. This is regardless of the machine type, like Master, Backup Master or Satellite.
IRC Reset after ALL CLERK CCD Report
C 7.2
After the ALL CLERK CCD Report has been carried out at the Master, all machines in an Inline
System needs to be reset their inline working RAM. By using this ROM Version, the Master will
initiate an IRC Reset at every machine in an Inline System. While the IRC Reset is carried out, a small
information window is shown on the screen of each machine. This information window will
disappear automatically.
System needs to be reset their inline working RAM. By using this ROM Version, the Master will
initiate an IRC Reset at every machine in an Inline System. While the IRC Reset is carried out, a small
information window is shown on the screen of each machine. This information window will
disappear automatically.
Mix&Match timing
C 7.3
If several Promotion tables have been created which are active for different days and for different
start and end time, a wrong table could be considered for the promotion calculation by mistake.
This is corrected in this version.
start and end time, a wrong table could be considered for the promotion calculation by mistake.
This is corrected in this version.
Block size of the Clerk file during Inline setup
C 7.4
Dependently on the SRV parameter the size of the Clerk file will be adjusted during the Inline setup
at the Satellite machine. In case of overlapped Clerk function beside of Supervisor with own
account feature have to be used, the block size of the Clerk file becomes 1, but should be 2. With
the new version, the block size for the Clerk file will be set correctly.
at the Satellite machine. In case of overlapped Clerk function beside of Supervisor with own
account feature have to be used, the block size of the Clerk file becomes 1, but should be 2. With
the new version, the block size for the Clerk file will be set correctly.
VAT per Department missing in Saved Reports
C 7.5
Unfortunately, the VAT per Department information’s is missing in the Saved Reports. Since Version
1.67 they are included.
1.67 they are included.
Supervisor with own account and PLU per Clerk
C 7.6
If the Supervisor works for another Clerk the made turnover will correctly be added to the totalizers
of that Clerk he is working for, but the registered PLU’s will still be stored to the Supervisor’s
account. By the new version the turnover as well as the PLU per Clerk totalizers will be updated for
the Clerk the Supervisor work for.
of that Clerk he is working for, but the registered PLU’s will still be stored to the Supervisor’s
account. By the new version the turnover as well as the PLU per Clerk totalizers will be updated for
the Clerk the Supervisor work for.
Same CC# for the TimeOut operation, done directly after ALL-CLERK-Z report.
C 7.7
Condition: Overlapped Clerk function is enabled. Furthermore the Employee system is active and
the SRV parameter #987B (Automatic Clerk Sign on after time-in/break-out, and Automatic Clerk
Sign off after time-out or employee and clerk relationship is removed) is set to +4.
Phenomenon: If a TimeOut for an Employee is done directly after an ALL-CLERK-Z report has been
issued, the CC# for the TimeOut operation is the same as for the report. This is corrected.
the SRV parameter #987B (Automatic Clerk Sign on after time-in/break-out, and Automatic Clerk
Sign off after time-out or employee and clerk relationship is removed) is set to +4.
Phenomenon: If a TimeOut for an Employee is done directly after an ALL-CLERK-Z report has been
issued, the CC# for the TimeOut operation is the same as for the report. This is corrected.
UP-3500/3515
Manual – V1.6x
Changes / Improvements / Corrections since V1.68
Doc: up35xx_pm_e_1v68.docx
Page 30 / 43
Parts & Technical Services
>>> Changes / Improvements / Corrections since V1.68 <<<
C 8
Article missing by using the RECALL GLU function (8199)
C 8.1
By using the RECALL GLU function it happens that one or even more articles are missing from the
reopened GLU. This is corrected.
reopened GLU. This is corrected.
Promotion miscalculation (8205)
C 8.2
If several Promotion tables have been created which are active for different days and for different
start and end time, a wrong table could be considered for the promotion calculation by mistake.
This is corrected in this version. Remark: This phenomenon is similar to that one which has been
solved at V1.67 already.
start and end time, a wrong table could be considered for the promotion calculation by mistake.
This is corrected in this version. Remark: This phenomenon is similar to that one which has been
solved at V1.67 already.
Wrong Mode set after reset (7859)
C 8.3
The machine is set e.g. to the German-Fiscal-Mode. Make the following:
- Switch the Reset switch. Machine is showing the mode selection screen.
- Select e.g. Netherland-Fiscal-Mode. Next screen is showing Master Reset/Master Reset2.
- Switch the Reset switch again and select PRG. RESET.
Now the machine is set to the Netherland-Fiscal-Mode by mistake.
With this version the machine will stay in its mode even after above described operation.
- Switch the Reset switch. Machine is showing the mode selection screen.
- Select e.g. Netherland-Fiscal-Mode. Next screen is showing Master Reset/Master Reset2.
- Switch the Reset switch again and select PRG. RESET.
Now the machine is set to the Netherland-Fiscal-Mode by mistake.
With this version the machine will stay in its mode even after above described operation.
UP-3500/3515
Manual – V1.6x
New / Changed Parameters
Doc: up35xx_pm_e_1v68.docx
Page 31 / 43
Parts & Technical Services
P 1 >>> New/Changed Parameters (since V1.22) <<<
SRV
P 1.1
• #901A +4
VAT ratio for PLU
V1.30
•
• #907D +1
• #907D +1
EJ reading and printing in case of compulsory CCD
V1.50
•
• #908C +1
• #908C +1
Reset Transaction number after Closed Transaction Z Report
V1.30
•
• #919C +1
• #919C +1
Change of entry amount by with/without (correction of PM)
V1.40
•
• #921C +4
• #921C +4
VAT Shift toggle
V1.22
•
• #929A
• #929A
Solid line printing for KP, Receipt and KP
V1.30
•
• #981B +1
• #981B +1
Clear Data Entries by Open Receipt
V1.22
• #981D +1
PLU-Search Algorithmen
V1.30
•
• #986A +2
• #986A +2
The last Employee makes TimeOut, without prior CCD
V1.31
• #986C +4
Detailed General Report data print on Journal and in E/J
V1.22
•
• #987B +2
• #987B +2
Employee password in case of –Sales and –Consumption
V1.30
• #987C +2
Supervisor can work on his own account
V1.30
• #987D +2
ST(%), ST(-) and GrpDisc(%) discounts
V1.22
•
• #988C n
• #988C n
Number of copies of the CCD report in case of Terminal-CCD
V1.30
•
• #989A +4
• #989A +4
Print Customer details on Customer Ordering report
V1.40
• #989A +2
Print details on Closed Transaction report
V1.40
• #989A +1
Print CCD DIFF on CCD report for SHIFT CCD
V1.40
• #989B +4
KP –“ALL/NEXT” –“GROUP” finalization key is NBAL or FINAL
V1.40
• #989B +2
Print all items for KP Hold&Go
V1.40
• #989B +1
KP Hold&Go
V1.40
• #989C +4
Recapitulation for same Sideable PLU on bill
V1.40
• #989C +2
Save Name&Address automatically
V1.40
• #989C +1
Compulsory Name&Address for GLU registration
V1.40
• #989D +4
Report PLU details in Electronic Journal
V1.40
• #989D +2
Report details in Electronic Journal
V1.40
• #989D +1
not used
UP-3500/3515
Manual – V1.6x
New / Changed Parameters
Doc: up35xx_pm_e_1v68.docx
Page 32 / 43
Parts & Technical Services
•
• #990A +4
• #990A +4
Open drawer at TimeOut of last Employee
V1.40
• #990A +2
Print TAX for non-turnover items
V1.40
• #990A +1
Show error for faulty bill print from Orderman
V1.40
• #990B +4
Print Terminal Mail
V1.40
• #990B +2
Orderman NBAL is “KP ALL GROUP” or “NBAL”
V1.40
• #990B +1
GLU status in Registration Screen
V1.44
• #990C +2/4
Print outs for Customer registration
V1.44
• #990D +4
not used
• #990D +2
not used
• #990D +1
Support of UPC-E or 6 digit PLU code
V1.44
•
• #991A +4
• #991A +4
Checking of SCM(-) amount
V1.44
• #991A +1/2
GLU key status after Media & Bill
V1.44
• #991B +4
Print status shown in GLU KEY
V1.50
• #991B +2
Order status shown in GLU KEY
V1.50
• #991C +4
Copy PLU TEXT 1 to PLU KEY TEXT
V1.50
• #991C +2
Compulsory receipt print for GLU with FOOD item registration
V1.50
• #991C +1
Compulsory receipt print for GLU registration
V1.50
• #991D +4
Double height lines in Mask
V1.50
• #991D +2
Print of Employee Name by Employee-Sales-Cons.
V1.50
• #991D +1
Print “You saved” by a discount
V1.50
•
• #992A +4
• #992A +4
European Fiscal Electronic Journal
V1.60
• #992A +2
Grant M&M discount in Employee –Consumption –Sales
V1.50
• #992A +1
Grant M&M discount in Customer –Sales
V1.50
• #992B +4
Carry out of “Secured Reports on SD Card” manually
V1.60
• #992B +2
Register item with fractional quantity if Mix&Match is set
V1.60
• #992B +1
Save&Clear EJ on SD Card after Gen. Z
V1.60
• #992C +4
Contactless Clerk Key for Employee Time In/Out
V1.64
• #992C +1
Display screen #30 only if a Clerk is signed on
V1.65
• #992D +1
Display screen only if a Clerk is signed on
V1.65
•
• #997
• #997
IP and port number for PC server for Ethernet communication
V1.67
Click on the first or last page to see other UP-3515 service manuals if exist.