Sharp RZ-X660 (serv.man3) Service Manual ▷ View online
79
G. CON8-YW396-02(Yeonho)
H. CON9-Jumper Header 1x12x2.54mm
Pin
Description
Pin
Description
1
+12V DC Outut
2
GND
Pin
Description
Pin
Description
1
+5 Volt
7
KEY Pin
2
COM2 COMMON
8
COM4 COMMON
3
+12 Volt
9
+12 Volt
4
+5 Volt
10
+5 Volt
5
COM3 COMMON
11
+5 Volt
6
+12 Volt
12
+12 Volt
80
I. COM 2/3/4-Jumper Header 2x3x2.54mm
Pin
Description
1
+5 Volt
2
NC
3
+12 Volt
4
COM Port Voltage
5
COM Port Voltage
6
COM Port Voltage
81
Installation of Memory Module (SO-DIMM)
VCT-S5 motherboard provides one 204-pin DDR3 (Double Data Rate 3) SO-DIMM slot,
which supports Dual Channel DDR3L (low voltage).
VCT-S5 motherboard provides one 204-pin DDR3 (Double Data Rate 3) SO-DIMM slot,
which supports Dual Channel DDR3L (low voltage).
Step 1. Align a SO-DIMM on the slot such that the notch on the SO-DIMM matches
the break on the slot.
Step 2. Firmly insert the SO-DIMM into the slot until the retaining clips at both ends
fully snap back in place and the SO-DIMM is properly seated.
» It is not allowed to install a DDR or DDR2 memory module into a DDR3 slot; otherwise, this
motherboard and SO-DIMM may be damaged.
» Please make sure to disconnect the power supply before adding or removing SO-DIMMs or the
system components.
» The SO-DIMM only fits in one correct orientation. It will cause permanent damage to the
motherboard and the SO-DIMM if you force the SO-DIMM into the slot at incorrect orientation.
- Installing a SO-DIMM
HARDWARE INSTALLATION
Installing System Memory
82
Step 1. Before installing the expansion card, please make sure that the power supply
is switched off or the power cord is unplugged. Please read the
documentation of the expansion card and make necessary hardware settings
for the card before you start the installation.
documentation of the expansion card and make necessary hardware settings
for the card before you start the installation.
Step 2. Remove the system unit cover (if your motherboard is already installed in a
chassis).
Step 3. Remove the bracket facing the slot that you intend to use. Keep the screws for
later use.
Step 4. Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
Step 5. Fasten the card to the chassis with screws.
Step 6. Replace the system cover.
Step 6. Replace the system cover.
- Installing an expansion card
Expansion Slots (mini-PCIe and PCI Express Slot)
There is 1 mini-PCIe slot and 1 PCI Express slot on this motherboard.
There is 1 mini-PCIe slot and 1 PCI Express slot on this motherboard.
mini-PCIe slot: MINI_PCIE1 (mini-PCIe slot; half size) is used for PCI Express mini cards.
PCIE slot:
PCIE slot:
PCIE1 (PCIE x1 slot) is used for PCI Express x1 lane width cards.
Jumpers Setup
- Clear CMOS Jumper (CLRCMOS1)
The illustration shows how jumpers are setup. When the jumper cap is
placed on pins, the jumper is “Short”. If no jumper
cap is placed on pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap is
placed on these 2 pins.
placed on pins, the jumper is “Short”. If no jumper
cap is placed on pins, the jumper is “Open”.
The illustration shows a 3-pin jumper whose
pin1 and pin2 are “Short” when jumper cap is
placed on these 2 pins.
Click on the first or last page to see other RZ-X660 (serv.man3) service manuals if exist.