Sharp PRS PRODUCTS Service Manual ▷ View online
UP-600/UP-700VPS
13
[S/S#012] : MRS = 0000
S/S#012-A:
1. RA1 is used to add value to the
vending purse.
vending purse.
RA1 Adds value to
Vending purse
S/S#012-A
NO
0
YES
1
S/S#012-B:
1. Refresh 2 adds to purse 2
Refresh 2 Adds to purse
2
S/S#012-B
NO
0
YES
1
Note : This is a similar setting to S/S#006[B] + 1
(Refresh adds to purse 2), but is used to control the
second daily refresh.
S/S#012-C:
1. Display Vending purse value in
display Card function
2. Print Vending purse value in
Print Card function
3. Print Vending purse value on
display Card function
2. Print Vending purse value in
Print Card function
3. Print Vending purse value on
receipts
Print Vending
purse on
receipts
Print Vending
purse in Print
card function
Display
Vending purse
in Display card
in Display card
function
S/S#012-C
NO
NO
NO
0
YES
1
YES
NO
2
YES
3
YES
NO
NO
4
YES
5
YES
NO
6
YES
7
[S/S#013] : MRS = 0000
S/S#013-A:
Unused.
S/S#013-B:
Display of card information on UP-
P16DP during print card function.
P16DP during print card function.
Card Information to be
displayed on UP-P16DP
S/S#013-B
None
0
Balance
1
Purse 1
2
Purse 2
3
S/S#013-C:
Display of card information on UP-
P16DP during display card function.
P16DP during display card function.
Card Information to be
displayed on UP-P16DP
S/S#013-C
None
0
Balance
1
Purse 1
2
Purse 2
3
S/S#013-D:
Display of card information on UP-
P16DP after receipt issue on card
transactions.
P16DP after receipt issue on card
transactions.
Card Information to be
displayed on UP-P16DP
S/S#013-D
None
0
Balance
1
Purse 1 value
2
Purse 2 value
3
14
[S/S#014] : MRS = 0000
S/S#014-D:
1. Selection of card reader type.
SharpSmart Card Reader Type
S/S#014-D
Mifare reader
1
PRS reader
2
[S/S#015] : MRS = 0000
S/S#015-A:
1. Allow Credit 10 to spend from points
purse.
purse.
Credit 10 spends from
points purse
S/S#015-A
NO
0
YES
2
Note : The above feature only works when the redeem1
settings in PGM2 mode are set in such a way that 1
point has a value of 0.01 (eg 1 pence, or 1 cent)
UP-600/UP-700VPS
15
Authorisation Process
For this model (UP-800), a 32 character code is
obtained by accessing the SRV mode, and selecting
Setting; SharpSmart; Licence code. This 32 character
number is relayed to PRS, whereupon a response code
(16 characters) is issued and keyed in.
Care should be taken to not cancel or leave the initial
code screen until after the response code has been
keyed, otherwise the process must be re-started. You
may switch off the unit while awaiting the response
code.
The licence code, once entered, should be saved (using
the “SAVE LIC.” option) otherwise it will be lost in any
subsequent MRS. If at any future time a new Flash
ROM is installed, a new licence will have to be issued.
The following screens must be selected to enter
Licence code programming
obtained by accessing the SRV mode, and selecting
Setting; SharpSmart; Licence code. This 32 character
number is relayed to PRS, whereupon a response code
(16 characters) is issued and keyed in.
Care should be taken to not cancel or leave the initial
code screen until after the response code has been
keyed, otherwise the process must be re-started. You
may switch off the unit while awaiting the response
code.
The licence code, once entered, should be saved (using
the “SAVE LIC.” option) otherwise it will be lost in any
subsequent MRS. If at any future time a new Flash
ROM is installed, a new licence will have to be issued.
The following screens must be selected to enter
Licence code programming
Select "1 SETTING " and press the Enter key.
Display: SETTING item selection screen.
Display: SETTING item selection screen.
Press "PAGE DOWN"
Select “13 PRS LICENCING”, Press the Enter key.
Select "1 LICENCE CODE", Press the Enter key.
Display: "LICENCE CODE" screen
Enable required products by pressing the decimal
point key (
)
.
16
Press Enter or TL
Display: "ID CODE" screen
Display: "ID CODE" screen
Enter: "AUTH CODE"
Press ENTER when complete.
Saving Licence Code to Flash Memory
It is possible to save the licence code into the UP-800
flash memory, so that in the event of system crash
(memory loss) it can be recovered (for example after
MASTER RESET).
Select "2
SAVE LIC.” Press the Enter key.
Select "1 YES" press the Enter key
Recovering Saved Licence Code
If a failure occurs and the ECR is master reset, it will
have lost the licence code. However, if the licence code
was saved, it is possible to recover it from flash
memory.
have lost the licence code. However, if the licence code
was saved, it is possible to recover it from flash
memory.
Press “ENTER”
After confirmation, the licence is recovered from flash
memory.
Click on the first or last page to see other PRS PRODUCTS service manuals if exist.