Sharp XE-A217 (serv.man4) Service Manual ▷ View online
XE-A207/A217/A307
HARDWARE DESCRIPTION
– 29 –
4. SIGNAL CONNECTION DIAGRAM
Connection between the Host (PC) and the Terminal (ECR)
Note: If the connector of the Host PC is “9 PIN D-SUB,” the PIN num-
ber is the same as that of the ECR.
5. SETTING OF RS232 PORT
The signal of 9-pin for RS232 port can be changed to “RI” or “+5V” by
positioning the short pin of “SP3” on the main PWB.
positioning the short pin of “SP3” on the main PWB.
However the factory-shipped location of the short pin varies depending
on the models.
Specifications of RS232 port
Usage: For Standard RS232 port
Connector: D-SUB 9pin
Data rate: max. 38,400 bps.
Power Supply: 5V/400mA (*)
Pin assign
* Default Setting
XE-A207/A217: RI (SP3: 2pin - 3pin)
XE-A307: +5V (SP3: 1pin - 2pin)
Setting of SP3
SD
Transmitted Data
RD
Received Data
DTR (ER)
Data Terminal Ready
DSR (DR)
Data Set Ready
RTS (RS)
Request To Send
DCD (CD)
Data Carrier Detector
CTS (CS)
Clear To Send
FG
Frame Ground
9PIN D-SUB
PC side
9PIN D-SUB
ECR side
Pin No.
Signal Name
1
CD
2
RXD
3
TXD
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9 (*)
RI/+5V
Signal
Setting of SP3
RI
2pin, 3pin
+5V
1pin, 2pin
SP3
䃂䇭
䃂䇭
3
RI
䃂䇭
䃂䇭
2
+5V
䃂䇭
䃂䇭
1
SP3
XE-A207/A217/A307
DIAGNOSTIC PROGRAM DESCRIPTION
– 30 –
CHAPTER 6. DIAGNOSTIC PROGRAM DESCRIPTION
By selecting SERVICE from the DIAG MENU, the following screen is
displayed in the LCD.
The selected item is highlighted in the displayed menu.
You can change the selected item by using the [
2 ] / [ 4 ] key, and
press the [TL/NS] key to execute the selected item.
1. DIAGNOSTIC PROGRAM
START PROCEDURES
1) Check to see that the SD card is in place.
2) Set the paper roll.
3) Check to see that the AA batteries are set.
4) Set the RS232C loopback connecter.
5) Plug the AC cord to the outlet while holding down the [RECEIPT]
key and [CL] key.
6) Language selection menu is displayed. Push the corresponding
number key.
7) Set current date/time and push [TL/NS] key.
8) Set tax rate and push [TL/NS] key.
9) Set mode pass code and push [TL/NS] key.
10) Set manager pass code and push [TL/NS] key.
11) Set logo message and push [TL/NS] key.
12) REG mode screen is displayed.
Push the [MODE] key.
13) Enter “99999999,” confirm that the screen displays as below, and
then press the [TL/NS] key.
14) The following screen is displayed in the LCD.
SERVICE DIAG
KEY
SENSOR
SD CARD
LED&BZ
DRAWER
LCD
RS232C
A/D
PRINTER
ROM
RAM
CLOCK
RAM
CLOCK
SERVICE DIAG MENU
XE-A207/A217/A307
DIAGNOSTIC PROGRAM DESCRIPTION
– 31 –
15) Make “4. DIAGNOSTIC” highlighted with the [
2 ] key or [ 4 ] key,
and press the [TL/NS] key.
16) The following screen is displayed in the LCD.
17) Enter “907 · .”
18) The following screen is displayed in the LCD.
19) Confirm that “SERVICE” is highlighted, and press the [TL/NS] key.
2. KEY
1) Press any key other than the [RECEIPT] and [TL/NS] key.
2) Press the [TL/NS] key at the end.
If you make a wrong operation, press the [CL] key three times to start
over from the beginning.
After the test result is displayed and printed out, press the [TL/NS] key
After the test result is displayed and printed out, press the [TL/NS] key
again to go back to the previous screen.
S1: SUM1
S2: SUM2
Caution: To have printout of test results, as XE-A307 has 2 sheets for
the printer, be sure to use both printers to print it out.
CHECK SUM:
1509(XE-A207)
37BF(XE-A217)
37BF(XE-A217)
15A2 (XE-A307)
3. SENSOR
SENSOR: This inspects the sensor circuit of the printer.
Result of detecting whether the printer paper is available.
(YES: Paper available, NO: No paper)
(YES: Paper available, NO: No paper)
1) Check the status of SENSOR.
(The status of SENSOR is displayed in real time at an interval of 1
second.)
2) Press the [TL/NS] key to end the test.
Caution: To have printout of test results, as XE-A307 has 2 sheets for
the printer, be sure to use both printers to print it out.
PASSWORD? ____
DIAG MENU
SERVICE
Specified SUM
Current SUM
(It changes each time the key is pressed.)
(It changes each time the key is pressed.)
Test Result
KEY NORMAL
KEY CORD:XXX
S1:XXXX S2=YYYY
NG
KEY CORD:XXX
S1:XXXX S2=YYYY
NG
LCD display (when the test result is NG.)
KEY XXXX-YYYY - NG
Printout (when the test result is NG.)
KEY NORMAL
KEY CORD:XXX
S1:XXXX S2=YYYY
OK
KEY CORD:XXX
S1:XXXX S2=YYYY
OK
LCD display (when the test result is OK.)
KEY XXXX-YYYY - OK
Printout(when the test result is OK.)
SENSOR
PPR1:NO
PPR1:NO
XE-A207/A217(when PPR1 is NO.)
LCD display
SENSOR
PPR1:NO
PPR2:NO
PPR1:NO
PPR2:NO
XE-A307 (when PPR1,PPR2 are NO.)
SENSOR
PAPER1 NO
PAPER1 NO
XE-A207/A217(when PPR1 is NO.)
Printout
SENSOR
PAPER1 NO
PAPER2 NO
PAPER1 NO
PAPER2 NO
XE-A307(when PPR1,PPR2 are NO.)
SENSOR
PPR1:YES
PPR1:YES
XE-A207/A217(when PPR1 is YES.)
LCD display
SENSOR
PPR1:YES
PPR2:YES
PPR1:YES
PPR2:YES
XE-A307(when PPR1,PPR2 are YES.)
SENSOR
PAPER1 YES
PAPER1 YES
XE-A207/A217(when PPR1 is YES.)
Printout
SENSOR
PAPER1 YES
PAPER2 YES
PAPER1 YES
PAPER2 YES
XE-A307(when PPR1,PPR2 are YES.)
XE-A207/A217/A307
DIAGNOSTIC PROGRAM DESCRIPTION
– 32 –
4. SD CARD
This detects the SD card, and displays the status of Write Protect in real
time. Also, it displays the CID register of the SD card.
Press the [TL/NS] key to end the test.
CD: CARD DETECT
WP: WRITE PROTECT
Caution: To have printout of test results, as XE-A307 has 2 sheets for
the printer, be sure to use both printers to print it out.
5. LED & BUZZER
This tests the LED display and Buzzer.
LED display
The following display modes are repeated.
• Segment display
The segments light up in the following pattern. The unit makes a short
beep every time the [TL/NS] key is pressed, and it goes on to the next
pattern.
pattern.
• Sift display
The segments light up in the following pattern. The unit makes a short
beep every time the [TL/NS] key is pressed, and it goes on to the next
beep every time the [TL/NS] key is pressed, and it goes on to the next
pattern.
All the segments light up at the end, and it keep beeping.
By pressing the [TL/NS] key, this test ends with OK.
By pressing any key other than the [TL/NS] key, this test ends with the
result of NG.
result of NG.
Caution: To have printout of test results, as XE-A307 has 2 sheets for
the printer, be sure to use both printers to print it out.
SD CARD
CD: NO , WP: NO
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
LCD display
ȪCDȇNO, WPȇNOȫ
SD CARD
CD:NO ,WP:NO
CID:XXXXXXXXXXXXXXXX
CD:NO ,WP:NO
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
Printout
ȪCDȇNO, WPȇNOȫ
SD CARD
CD: YES , WP: YES
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
LCD display
ȪCDȇYES, WPȇYESȫ
SD CARD
CD:YES ,WP:YES
CID:XXXXXXXXXXXXXXXX
CD:YES ,WP:YES
CID:XXXXXXXXXXXXXXXX
XXXXXXXXXXXXXXXX
Printout
ȪCDȇYES, WPȇYESȫ
LED &BUZZER
TL:OK,OTHER:NG
LCD display
The rest of the illustrations are omitted.
The rest is omitted.
The rest is omitted.
"A" is displayed
instead of "10."
instead of "10."
LED
NG
Printout (when the test result is NG.)
OK
LED
Printout (when the test result is OK.)
Click on the first or last page to see other XE-A217 (serv.man4) service manuals if exist.