Sharp XE-A113 (serv.man3) Service Manual ▷ View online
XE-A113 (V)
SPECIFICATIONS
– 3 –
■Machine state symbols
Segment
Decimal Point
6. PRINTER
1) Printer
• Part number
: M-T53II
• NO. of station
: 1 (Receipt or journal)
• Validation
: No.
• Printing system
: Line thermal
• No. of dot
: 288 dots
• Dot pitch
: Horizontal
0.167mm
Vertical
0.167mm
• Font
: 10 dots (W)
×
24 dots (H)
• Printing capacity
: max. 24 characters
• Character size
: 1.67 (W)
×
4.0 (H) mm at 10
×
24 dots
• Print pitch
: Column distance
2.0mm
Row distance
5.0mm
• Max. Print speed
: Approximate 60mm/s (Approximate 12 l/s)
• Max. Paper feed speed: Approximate 60mm/s (Approximate 12 l/s)
(Manual feed)
: Approximate 40mm/s (Approximate 12 l/s)
• Reliability
: Mechanism LIFE 6 million lines used to
high-quality thermal paper
• Paper end sensor
: Set up
• Cutter
: No
• Near end sensor
: No
2) Paper
3) Logo stamp
• No
: Appears during programming.
: Appears when an error is detected.
: Appears when the subtotal is displayed or when the amount
tendered is smaller than the sales amount.
: Appears when the [CONV] key is pressed to calculate a subto-
tal in foreign currency.
: Appears when a transaction is finalized by pressing the [CA/AT/
NS], [CHK] or [CH] key.
: Appears when the change due amount is displayed.
: May appear in the far-left three positions at the timing of key
entry when the electronic journal (EJ) memory is full. (Depend-
ing on programming.)
ing on programming.)
: Appears when the voltage of the installed batteries is under the
required level. You must replace with new ones within two days.
: Appears when the batteries are not installed, or the installed
batteries are dead. You must replace with new ones immedi-
ately.
: May appear right below the eighth and ninth places at the timing
of finalization of a transaction when the electronic journal (EJ)
memory is nearly full.
Also appears right below the tenth place when power save
Also appears right below the tenth place when power save
mode is effective.
: Appears when the print roller arm is not locked.
: Appears when the paper is not set or has run out.
Display
position
Description
Amount
1-8
Minus sign
2-10
-
: Floating
Error
8-10
Exx : xx
=
error code
PGM Mode
10
P
CASH, CHECK,
CHARGE
CHARGE
10
F
: Light up when a registration is
f i n a l i z e d b y d e p r e s s i n g
[CASH], [CHECK], [CHARGE]
key
f i n a l i z e d b y d e p r e s s i n g
[CASH], [CHECK], [CHARGE]
key
SUB TOTAL/
short tender
short tender
10
o
Change
10
C
: Light up whenever the change
due amount appears in the dis-
play.
due amount appears in the dis-
play.
Currency
Conversion
Conversion
10
c
: Light up whenever the foreign
amount appears in the display.
amount appears in the display.
Department
9-10
No zero-suppressed
PLU
7-10
No zero-suppressed
Repeat
8
Endless count, starting from 2.
Receipt OFF
9
_
DC
_
: Double size character entry
status
status
SHIFT
_
: Shift character entry status
NUMBER
_
: Number character entry sta-
tus
tus
Clerk No.
2, 3
-xx- : clerk number
EJ FULL
8-10
E-E: Light up when EJ memory is
FULL at the timing of key entry
(by PGM selection).
(by PGM selection).
Low Battery
10
L
:
No Battery
10
:
Display
position
Description
Decimal point
7-1
TAB
4-1
EJ near full
8, 9
(by PGM selection)
• Paper roll dimension: 57.5
±
0.5mm in width
Max. 80mm
in diameter
• Paper quality:
High-quality thermal paper
paper thickness : 0.06 to 0.08mm
Nihon seisi thermal paper : TF50KS-E
Oji thermal paper : PD150R,
PD160R
XE-A113 (V)
SPECIFICATIONS
– 4 –
4) PRINTING AREA
Number of thermal head heater elements 288 dots
7. DRAWER
[OUTLINE]
• Standard equipment: Yes (1)
• Max. number of additional drawers: 1
• The drawer consists of:
1) Drawer box (outer case) and drawer
2) Money case
3) Coin case
4) Lock (attached to the drawer)
[SPECIFICATION]
1) DRAWER BOX AND DRAWER
2) MONEY CASE
Layout:
3) Drawer Lock Key
This key locks and unlocks the drawer. To lock it, turn 90 degrees coun-
terclockwise. To unlock it, turn 90 degrees clockwise.
terclockwise. To unlock it, turn 90 degrees clockwise.
8. USB PORT
[DEVICE]
USB B Type
[OUTLINE]
This ECR has 1 port.
This is used in order to connect with a personal computer.
[SPECIDICATIONS]
1) Transmission rate
USB 2.0 Full Speed Max. 12Mbps
2) Connector
USB B Type
3) Pin assign
1Pin 5V
2Pin
−
D
3Pin
+
D
4Pin GND
9. BATTERY
1) MEMORY BACK UP BATTERY
For memory back up, the alkaline battery AA (3 pieces) are needed.
[Specifications]
1. Memory holding time:
Approximate 1 year after new alkaline batteries are installed.
2. Battery exchange method:
When the low battery symbol “L” lights up, batteries (3 pieces)
exchange by the following method, within 2 days.
1) Power on the ECR.
2) Mode switch turn to “REG” mode.
3) Remove the old alkaline batteries (3 pieces).
4) Insert the new alkaline batteries (3 pieces).
5) Confirm the low battery symbol “L” lights off.
2) LOW BATTERY
Low battery indication will appear on the left side of display when the
battery voltage is low.
battery voltage is low.
CASE 1:
When any numeric entry & any item entry is not done or
just after finalization.
The machine can indicate the low battery condition. (Always)
Model name of the drawer box
SJ-415
Size
330 (W)
×
420 (D)
×
94 (H) mm
Material
Metal
Bell
–
Release lever
Standard equipment:
Situated at the bottom
Situated at the bottom
Drawer open sensor
–
Separation from the drawer
Disallowed
Separation of the coin compartments from the bill
compartments
compartments
Allowed
Bill separator
–
Number of compartments
3B/6C
0.167
(4.75)
(4.75)
48 (288 dots)
print area
(max.24 characters)
(units : mm)
57.5±0.5
(Paper dimension)
3B/6C
XE-A113 (V)
OPTIONS
– 5 –
CASE 2:
When numeric entry or item entry is done.
Battery condition will not appeared.
Exceptionally, at the power is restored after power failure, the low bat-
Exceptionally, at the power is restored after power failure, the low bat-
tery condition will appear on the display only when the battery is low.
And the indicator will disappear after any key entry.
[Display sample]
“
0.00” : Battery is OK.
“L
0.00” : Low battery (You have to change the batteries.)
“
0.00” : No battery (You have to change the batteries
immediately.)
After finalization
“F
12.34” : Battery is OK.
“L
12.34” : Low battery. (“L” indicate instead of “F”.)
“
12.34” : No battery. (“L” indicate instead of “F”.)
Note: “NO BATTERY”: When the “NO BATTERY” is display, the master
reset is executed at the timing of “POWER ON”
after the “POWER OFF”.
10. SD MEMORY CARD
[Device]
SD Card (Version. 1.01)
[Outline]
XE-A113 has a SD Memory Card slot.
[Specidications]
CHAPTER 2. OPTIONS
1. OPTIONS (No)
2. SERVICE OPTIONS (No)
3. SUPPLIES
4. SPECIAL SERVICE TOOLS (No)
CHAPTER 3. MASTER RESET AND PROGRAM RESET
1. MASTER RESETTING
Master resetting clears the entire memory and resumes initial values.
Master resetting can be accomplished by using the following procedure:
Procedure A:
1) Unplug the AC cord from the wall outlet or set the
mode switch to OFF Position.
2) Let the ECR be without the memory back up battery.
3) Wait over 1 muinite for discharging.
4) Set the mode switch to any position except OFF.
5) Plugin the AC cord to the wall outlet or turn the mode
switch from OFF Position to another position.
6) Insert batteries before carrying out operation after
master resetting.
The master reset can also be accomplished in the following case.
In case power failure occurs when the machine has no battery
attached to it, the master reset operation is automatically performed
attached to it, the master reset operation is automatically performed
after the power has been restored.
(This is because if power failure occurs with no battery attached to
the machine, all the memories are lost and the machine does not
work properly after power recovery; this requires the master reset
work properly after power recovery; this requires the master reset
operation.)
2. PROGRAM RESETTING
(INITIALIZATION)
This resetting resumes the initial program without clearing memory.
This resetting can be operated at below sequence in PGM mode.
Procedure:
1) Unplug the AC cord from the wall outlet.
2) Wait over 1 muinite for discharging.
3) Set the mode switch to the PGM position.
4) While holding down the FEED key, plugin the AC
cord to the wall outlet.
Note: In case power failure occurs when the machine has no battery
attached to it, the master reset operation is automatically per-
formed after the power has been restored.
1) Variable clock rate
: 0 - 25 MHZ
2) Other commands and memory access : 2.7 - 3.6V
3) Bus Protocol
: SPI Bus
4) Correspondence capacity
: 32MB - 512MB
5) Recommended manufacturer
: SanDisk
No.
NAME
PARTS CODE
PRICE RANK
DESCRIPTION
1
Thermal roll paper
TPAPR6645RC05
AY
5roll/pack (80
φ)
XE-A113 (V)
HARDWARE DESCRIPTION
– 6 –
CHAPTER 4. HARDWARE DESCRIPTION
1. HARDWARE BLOCK DIAGRAM
<Main parts>
2. MEMORY MAP
1MByte mode/The CS area PM13
=
1 is selected.
CPU
: M30624MGP-357FP (Renesus)
ROM 256KByte (MASK) RAM 20KByte
External RAM
: 1Mbit (128K
×
8)
CYPRESS CS18LV10245CCR70
Printer
: MT53II (EPSON)
RESET IC
BUZZER
12MHz
32.768kHz
DRY Battery
POWER
5.8V
5.0V
3.3V
7.9V
23.8V
DRAWER
MOTOR
PRINTER
MT53II
Driver/Sensor
KEY RETURN
KEY SCAN
KEY
SWITCH
Decoder
74HC138
×
2
4 to 16
LED
Front 10
Front 10
PopUp 7
DIG
Driver
SEG
Driver
74H374
S-RAM
128KByte
CPU
Renesus
M30624MGP-
357FP
357FP
ROM 256KByte
RAM 20KByte
RAM 20KByte
CPU internal RAM
: 20KByte 00400h-053FFh
External RAM
: 128KByte 08000h-27000h
(Area that can be used 124KByte)
00000h
00400h
053FFh
CPU internal RAM
20KByte 00400h-053FFh
05400h
08000h
External RAM
128KByte
27000h
28000h
30000h
Segment Latch Address
80000h
B0000h
FFFFFh
CPU internal MASK ROM
320KByte B0000h-FFFFFh
/CS0
/CS2
Click on the first or last page to see other XE-A113 (serv.man3) service manuals if exist.