Sharp XE-A107 (serv.man2) Service Manual ▷ View online
4-1
CHAPTER 4. HARDWARE DESCRIPTION & OPERATION PRICIPLE
1. OUTLINE
XE-A107
XE-A137,XE-A147
CPU
8bit MASK CPU
uPD780023AGC *4.19MHz
MASK ROM Built in (For Program)
uPD780023AGC *4.19MHz
MASK ROM Built in (For Program)
32bit CPU
MB9AF116N *16MHz
FLASH ROM Built in (For Program)
MB9AF116N *16MHz
FLASH ROM Built in (For Program)
PRINTER
58mm Print wheel type
58mm Thermal Printer
Rolling up
EU/Oceania/Asia/
ME/Africa
ME/Africa
Yes
None
SRAM
None
1Mbit(128kByte x8)
ROM
For Program
MASK ROM in CPU
FLASH ROM in CPU
DISPLAY
7segments LED
Display
digits
digits
EU/Oceania/Asia/
ME/Africa
ME/Africa
9 digits
KEY
Normal KEY: 30key
Mode S/W
5 steps rotary type
I/F
USB
None
SD
None
1slot
DRAWER
1port (For Standard drawer only. There is no optional drawer port)
RS232
None
1port ( for XE-A147)
EFT
None
POWER SUPPLY
AC adapter for XE-A107
AC adapter for XE-A137or XE-A147
BATTERY
MEMORY BACK UP
LR6 (AA size)
OPTIONAL
OPERATION BATTERY
OPERATION BATTERY
None
Option: XE-A1BT (XE-A147only)
DRAWER
Standard: 1 unit
4-2
2. Block diagram
1) XE-A147 / XE-A137
1) XE-A147 / XE-A137
2) XE-A107
4-3
3. Description
1) DISPLAY
The display of these models is LED type. And there are 2 types
such as 8 digits and 9 digits. It is depend on the destination of
models.
such as 8 digits and 9 digits. It is depend on the destination of
models.
a. Display content
Display
Departments/PLU Code:
The department code or PLU code entered appears on the left.
For example, if the key for department 1 is pressed, "1" would
appear in the extreme left position.
For example, if the key for department 1 is pressed, "1" would
appear in the extreme left position.
Repeat:
Indicates the number of times the same department key is
pressed. If an entry is repeated more than ten times, only the
first digit is displayed (12 displays as "2").
pressed. If an entry is repeated more than ten times, only the
first digit is displayed (12 displays as "2").
(
) Error:
This symbol appears, accompanied by a warning beep, when an
error is made. If this occurs during a transaction because of an
excessive digit entry, simply press [CL] and re-enter correctly.
error is made. If this occurs during a transaction because of an
excessive digit entry, simply press [CL] and re-enter correctly.
(
) Program:
This symbol Appears on the display when the cash register is
being programmed in the Z/PGM mode.
being programmed in the Z/PGM mode.
(
) Finalization:
This symbol appears when a transaction is finalized by pressing
[CA/ AT/NS], [CH] or [CHK].
[CA/ AT/NS], [CH] or [CHK].
(
) Subtotal:
This symbol appears when [#/SBTL] is pressed and the cash
register computes the subtotal, and also when the amount
tendered is less than the total sale amount.
register computes the subtotal, and also when the amount
tendered is less than the total sale amount.
(
) Change:
This symbol appears whenever the change due amount is
displayed.
displayed.
( ) Exchange:
This symbol appears when [EX] is pressed to calculate a subtotal
in foreign currency
(
) Low battery:
This symbol appears when the power of the installed batteries is
below a certain level or you need to replace the batteries with
new ones. (see the "Maintenance" section for explanation.)
below a certain level or you need to replace the batteries with
new ones. (see the "Maintenance" section for explanation.)
(
) No battery:
This symbol appears when no batteries are installed, or the
installed batteries are empty.
installed batteries are empty.
In addition, the following appear when appropriate:
The minus sign (-) can appear in positions 2 to 8.
The decimal point appears in positions 1 to 3.
When entry of the secret code is necessary, "---" appears in
positions 1 to 4.
2) KEYBOARD AND MODE SW
a. Keyboard layout (ex XE-A107)
b. Key list
Key top
Description
0-9, 00
Numeric keys
↑
Paper feed key
○
X
/TM
Multiplication / Time key
CL
Clear key
Void key
ESC
Escape / help key
%
Percent key
PO
Paid out key
RA/VAT
Received on account / VAT key
SHIFT
Department shift key
PLU
PLU (Price Look Up) key
DEPT 1-4 (5-8)
Department 1-4 (5 -8) key
CR
Credit key
EX
Exchange key
CH
Check key
#/ST
Non add / Subtotal
TL/AT/NS
Total / Amount tendered / No sale key
4-4
Mode switch layout
c. Function
Turns the display off. No operations are possible
REG
Permit transaction entry
Permit correction after final a transaction
X/Flash
Permits printing of sales reports and display the
flash reports
flash reports
Z/PGM
Permits printing and resetting of sales reports and
programming
programming
3) BATTERY
a. MEMORY BACK UP BATTERY
For memory back up, the dry battery ULM-3 (3 pieces) are
needed.
needed.
1.
Memory holding time:
Approx. 1 year after New dry batteries are installed.
(It is depend on the battery capacity)
2.
Battery exchange method:
When the low battery symbol "L" lights up, replace the
batteries (3 AA) replaced by the following method;
batteries (3 AA) replaced by the following method;
1) Power on the ECR.
2) Mode switch turn to "REG" mode.
3) Remove the OLD dry batteries (3 pieces).
4) The no-battery symbol "
L
" light up.
5) Insert the NEW dry batteries (3 pieces).
6) Confirm the low battery symbol "L" and no-battery
symbol "
L
" is off.
b. LOW BATTERY
Low battery indication will appear on the left side of display when
the battery voltage is low.
the battery voltage is low.
CASE 1: When sitting idle or after completion of transaction. The
machine can indicate the low battery condition (Always)
CASE 2: Low battery indication will not appear during key
operations, but will appear after power up of the cash
register.
register.
[Display sample]
“0.00”: Battery is OK.
"L 0.00": Low battery (The batteries have to be replaced.)
"L 0.00": Low battery (The batteries have to be replaced.)
After finalization
"F 12.34": Battery is OK.
"L 12.34": Low battery ("L" indicate instead of "F".)
"F 12.34": Battery is OK.
"L 12.34": Low battery ("L" indicate instead of "F".)
c. NO BATTERY
If the user forgets to replace the battery and the battery voltage
falls below a certain level, or if a power failure occurs with no
batteries installed, the memory contents cannot be retained. The
CPU judges it as no battery and performs the master reset. In this
case, all the settings and registrations are cleared. If, however, the
power is continuously supplied to the AC cord, the memory
contents are retained.
falls below a certain level, or if a power failure occurs with no
batteries installed, the memory contents cannot be retained. The
CPU judges it as no battery and performs the master reset. In this
case, all the settings and registrations are cleared. If, however, the
power is continuously supplied to the AC cord, the memory
contents are retained.
Low battery:
Batteries are installed, but the voltage is
low. Memory back up can be done.
No battery: Batteries are not installed or the voltage is extremely
low. The master reset is executed when a power
failure occurs, when the batteries are not properly
changed.
failure occurs, when the batteries are not properly
changed.
Low battery & No battery indication will appear at the most left
position of display when the battery voltage is low.
position of display when the battery voltage is low.
CASE 1: When any numeric entry & item entry is not done or
just after
finalization.
The machine can indicate the battery condition. (Always)
finalization.
The machine can indicate the battery condition. (Always)
CASE 2: When numeric entry or item entry is done.
Battery condition is not appeared.
Exceptionally, at the power is restored after power failure,
the low battery & No battery indication will appear on the
display only when the battery voltage is low.
And the indication will disappear after any key entry.
Exceptionally, at the power is restored after power failure,
the low battery & No battery indication will appear on the
display only when the battery voltage is low.
And the indication will disappear after any key entry.
[Display sample]
" 0.00" : Battery is OK.
"L 0.00" : Low battery
"
L
0.00" : No battery
After finalization
"F 12.34": Battery is OK.
"L 12.34": Low battery ("L" indicate instead of "F".)
"
L
12.34": No battery ("L" indicate instead of "F"
Click on the first or last page to see other XE-A107 (serv.man2) service manuals if exist.