DOWNLOAD Sharp ER-A450 (serv.man5) Service Manual ↓ Size: 1.64 MB | Pages: 127 in PDF or view online for FREE

If your customer wants a receipt after you have finalized a transaction with the receipt function being in the
“OFF” status (no receipting), press the 

q

key. This will produce a receipt. Your register can also print a copy

receipt when the receipt function is in the “ON” status. If you want to make a copy, please consult your dealer.

Pressing the 

q

key in the OP X/Z mode before registration toggles the status “ON” and “OFF”.

Printing a copy receipt after making the entries shown below with the receipt function being in
the “OFF” status

When the receipt function is in the “ON” status and you press 
the 

q

key to make a second copy

When the receipt function is in the “ON” status, 
the “   COPY   ” symbol will be printed on the receipt.

Print on the 
receipt

Print on the 
journal

850 

2

3 

≈

150 

1
;

For receipting

→

q

1

You can use this function when you want to take a copy of guest check.
Press the 

g

key and make a desired entry.

The guest check copy has nothing to do with the memory.

As a default setting, it is set to print a graphic logo on the top of each receipt (header graphic logo), and another
graphic logo can be printed on the bottom of each receipt (footer graphic logo) with the job code #2616. You can
also print the graphic logos with the combination of 3-line header logo message or 3-line footer logo message, or
can print only logo message without graphic logo. Consult your dealer when you want to change the setting.

Header graphic logo

Footer graphic logo

3

g

1480 

2
;

2

q

g

Item entries

Finalization

When the receipt 
ON/OFF function is 
in the “OFF” status

This function allows you to switch from one cashier to another and to interrupt the first cashier’s entry. So the
second cashier can do his or her entry in this mode. For actual use of this function, consult your dealer.

Cashier 1: Entry started
Cashier 2: Cashier change (1 to 2), interrupt initiated
Cashier 2: Transaction finished (2)
Cashier 1: Cashier change (2 to 1), entry restart

• When the cashier and clerk system is applied for your register, you cannot operate the overlapped

cashier entry.

• The overlapped cashier entry is not effective while the tendering sale is going on.
• If any cashier is still making an entry (or has not finalized the transaction yet), the machine does

not run in any mode other than REG and MGR and can print no X/Z reports. The error code “E22”
and the corresponding cashier code(s) are displayed at this time.

1. Cashier 1 is assigned.

(1

‹

) 

100 

1

360 

3
3

2. Cashier 2 is assigned.

2 

‹

3 

≈

150 

2
;

3. Cashier 1 is assigned.

1

‹

100 

1

360 

3
;

The entry by cashier 1 is started.

The entry by cashier 2 is started.

(The entry by cashier 1 is interrupted.)

The transaction by cashier 2 is finalized.

The entry by cashier 1 is restarted.

The transaction by cashier 1 is finalized.

When power is lost, the machine retains its memory contents and all information on sales entries.

•  When power failure is encountered in register idle state or during an entry, the machine returned to the normal

state of operation after power recovery.

•  When power failure is encountered during a printing cycle, the register 

prints “========” and then carries out the correct printing procedure 
after power recovery. (See the sample print.)

If the printer runs out of paper, the printer will stall, “PPPPPPPPPP” will appear on the display, and the register
will start to continuously produce an intermittent beeping tone. Key entries will not be accepted. Referring to “5.
Installing and removing the paper roll” in this chapter, install a new roll paper in the proper position, then press
the 

c

key. The printer will print the power failure symbol and resume printing.

If the print head comes up, the printer stalls, “H” will appear on the very left of the display, and the register will
start to continuously produce an intermittent beeping tone. Key entries will not be accepted. Bring back the print
head to the correct position, then press the 

c

key. The printer will print the power failure symbol and resume

printing.

Your register prints by means of thermal printing. The print head applies heat to thermal paper which is
chemically treated to change color when heated to a certain level. This creates the printed text.

• If you are not going to use the register for an extended

period of time, pull the print head release lever toward you
so that the print head is set apart from the plate.

3

2

1

Printing position

Head-up position