Sharp ER-A410 / ER-A420 SCANNING (serv.man3) Service Manual ▷ View online
PERIPHERALS
Designs and specification are subject to change without notice Page 53
Quick Steps – Scale (NON UK)
To quickly setup the ER-A410/ER-A420 to interface with a Scale, please refer to the outlined
procedures below:
procedures below:
No.
Description
Comments/Procedure
Step–1
Connect the Scale
CH–1 or CH–2
Step–2
SRV Job#903-B, C, D
903 Æ [.] Æ [@] Æ x030 Æ [CA/AT]
(For 3 Decimal Places) or
903 Æ [.] Æ [@] Æ x020 Æ [CA/AT]
(For 2 Decimal Places)
(For 3 Decimal Places) or
903 Æ [.] Æ [@] Æ x020 Æ [CA/AT]
(For 2 Decimal Places)
Step–3
SRV Job#906-D
906 Æ [.] Æ [@] Æ xxx1 Æ [CA/AT]
(For Fractional Entries)
(For Fractional Entries)
Step–4
SRV Job#918
918 Æ [.] Æ [@] Æ x0xx Æ [CA/AT]
(For Non-Scale Fractional Entries) or
918 Æ [.] Æ [@] Æ x1xx Æ [CA/AT]
(For Disallowing Non-Scale Fractional Entries)
(For Non-Scale Fractional Entries) or
918 Æ [.] Æ [@] Æ x1xx Æ [CA/AT]
(For Disallowing Non-Scale Fractional Entries)
Step-5 SRV
Job#950
• Place the [SCALE] Key (Function #77) on the keyboard
• Place the [OPEN TARE] Key (Function #78) on the keyboard
• Place the [OPEN TARE] Key (Function #78) on the keyboard
Step-6
PGM Job #2690
2690 Æ [.] Æ [@] Æ 1 Æ @ Æ 0010 [SBTL] Æ [CA/AT] for CH–1)
or
2690 Æ [.] Æ [@] Æ 1 Æ @ Æ 0020 [SBTL] Æ [CA/AT] for CH–2)
or
2690 Æ [.] Æ [@] Æ 1 Æ @ Æ 0020 [SBTL] Æ [CA/AT] for CH–2)
Note:
Must match the physical connection
Step-7
Program Reset
• Place the SRV-Key counter-clockwise to 6 o’clock position
(SRV’ position)
• Count 5 seconds
• Turn SRV-Key clockwise to 7o’clock position (SRV position)
• Verify”***PROGRAM RESET has printed on the journal-side
• Turn SRV-Key clockwise to 7o’clock position (SRV position)
• Verify”***PROGRAM RESET has printed on the journal-side
tape.
Step-8
PGM Job #2110
-and/or-
PGM Job#2210
2110 Æ [.] Æ [@] Æ (Dept. No.) Æ @ Æ xyzxxx [SBTL] Æ [CA/AT]
–and/or-
2210 Æ [.] Æ [@] Æ (Dept. No.) Æ @ Æ xyz [SBTL] Æ [CA/AT]
Y = Tare Table No. (1–9)
Z = Scale Comp. /Enabled/Inhibited = 2/1/0
–and/or-
2210 Æ [.] Æ [@] Æ (Dept. No.) Æ @ Æ xyz [SBTL] Æ [CA/AT]
Y = Tare Table No. (1–9)
Z = Scale Comp. /Enabled/Inhibited = 2/1/0
PERIPHERALS
Designs and specification are subject to change without notice Page 54
Section–3: Slip
The following table shows the related SRV and PGM-Mode Job#s available for the ER-A410 and
ER-A420 ECRs when the Slip Printer is connected.
The following table shows the related SRV and PGM-Mode Job#s available for the ER-A410 and
ER-A420 ECRs when the Slip Printer is connected.
Slip Printer
Mode Job#
Description
913–B
Escape Compulsory SLIP & Validation
928–A
Printing of Slip Logo
Val. Message Printing on Slip
Val. Message Printing on Slip
928–B
Header Line Printing on Slip when Reorder Printing
Print PLU Items on Slip when $0.00
Print PLU Items on Slip when $0.00
928–C
Set PLU Items Print on Slip
PB/NBAL Prints on Slip
928–D
Slip Print Compulsion System
[PRINT]–Function #33
SRV-Mode
950
[SLIP]–Function #34
2690 Channel
Assignment
2320
Media Key Function Programming
PGM-Mode
2615
Validation Limitation Programming
PERIPHERALS
Designs and specification are subject to change without notice Page 55
1. Cabling Pin Outs:
ECR
SLIP PRINTER
9-Pin D–Sub 25-Pin D–Sub
2. Data Transmission:
-
8 Bits ASCII Code
-
No Start Bit
-
Non Parity
-
1 Stop Bit
-
Baud Rate: 9600 bps (fixed)
*Handshaking: DTR/DSR Control
PERIPHERALS
Designs and specification are subject to change without notice Page 56
TM-U295 Switch–1Settings:
ROM Version 1.08
Switch
Contents
On
Off
Setting
SW1-1
Data Receive Buffer
Ignored
Prints “?”
OFF
SW1-2
Receive Buffer Capacity
35 bytes
512 Kbytes
OFF
SW1-3 Handshaking
XON/XOFF
DTR/DSR
OFF
SW1-4
Data Word length
7 bits
8 bits
OFF
SW1-5
Parity Check
With Parity
Without Parity
OFF
SW1-6
Parity selection
Even Parity
Odd Parity
OFF
SW1-7 Baud
Rate
Selection
(*1)
OFF
SW1-8 Baud
Rate
Selection
(*1)
OFF
SW1-9
DSR (#6) Reset
Effective
Invalid
OFF
SW-10
Init (#25) Reset
Effective
Invalid
ON
(*1): SW1-7, 1-8 Definitions
Rate
SW1-7
SW1-8
1200 bps
ON
ON
2400 bps
OFF
ON
4800 bps
ON
OFF
9600 bps
OFF
OFF
Click on the first or last page to see other ER-A410 / ER-A420 SCANNING (serv.man3) service manuals if exist.