DOWNLOAD Sharp DX-AT50H (serv.man21) Service Manual ↓ Size: 3.04 MB | Pages: 76 in PDF or view online for FREE

– 9 –

(1) Using desoldering braid, remove the solder from the foil of

each pin of the flat pack-IC on the CBA so you can install
a replacement flat pack-IC more easily.

(2) The “ ” mark on the flat pack-IC indicates pin 1. (See Fig.

S-1-7.) Be sure this mark matches the 1 on the PCB when
positioning for installation. Then presolder the four corners
of the flat  pack-IC. (See Fig. S-1-8.)

(3) Solder all pins of the flat pack-IC. Be sure that none of the

pins have solder bridges.

Example :

Pin 1 of the Flat Pack-IC
is indicated by a " 

  

 " mark.

Presolder

CBA

Flat Pack-IC

Electrostatic breakdown of the semi-conductors may occur
due to a potential difference caused by electrostatic charge
during unpacking or repair work.

Be sure to wear a grounding band (1 Mohm) that is properly
grounded to remove any static electricity that may be charged
on the body.

Be sure to place a conductive sheet or copper plate with proper
grounding (1 Mohm) on the workbench or other surface, where
the semi-conductors are to be placed. Because the static
electricity charge on clothing will not escape through the body
grounding band, be careful to avoid contacting semi-conductors
with your clothing.

CBA

CBA

Grounding Band

Conductive Sheet or
Copper Plate

1Mohm

1Mohm

– 10 –

This flowchart indicates the disassembly steps to gain access to item(s) to be serviced. When reassembling, follow the steps in
reverse order. Bend, route, and dress the cables as they were originally.

[1]  TOP CABINET

[2]  BOTTOM CABINET

[3]  TOP SUPPORT ANGLE

[16]  TRAY PANEL

[4]  FRONT UNIT

[5]  FRONT ANGLE

[7]  FRONT CBA UNIT

[8]  LCD

[9]  DIFFUSION SHEET 

[10]  LIGHITING PLATE

[11]  REFLECTION SHEET

[12]  LCD HOLDER

[13]  FRONT CBA  ASSEMBLY

[6]  PWB SPACER

[14]  BACK PLATE

[15]  DVD MECHA UNIT

[18]  DVD MECHA 

[19]  POWER CBA  ASSEMBLY

[17]  MAIN CBA  ASSEMBLY

– 11 –

[1]

TOP CABINET

C1

5(S-1)

—

[2]

BOTTOM  CABINET

C1

2(S-2), 2(L-1), 2(S-2)

—

[3]

TOP SUPPORT ANGLE

C2

4(S-3)

—

[4]

FRONT UNIT

C2,

2(S-4), *CN1002

—

C5

[5]

FRONT ANGLE

C3

(*CN2001), 4(S-5)

—

[6]

PWB SPACER

C3

*(L-2)

—

[7]

FRONT CBA UNIT

C3

4(S-6)

—

[8]

LCD

C4

Desolder, *2(L-3)

—

[9]

DIFFUSION SHEET

C4

—

—

[10]

LIGHTING PLATE

C4

—

—

[11]

REFLECTION SHEET

C4

—

—

[12]

LCD HOLDER

C4

*(L-4)

—

[13]

FRONT CBA ASSEMBLY

C4

—

—

[14]

BACK PLATE

C5

7(S-7)

—

[15]

DVD MECHA UNIT

C5

3(S-8), Jack Angle,  *CN1001, *CN1003J, Erase Plate

—

[16]

TRAY PANEL

C5

*2(L-5)

—

[17]

MAIN CBA ASSEMBLY

C6,

4(S-9), *CN101, *CN4401, *CN303, *CN4402, *CN4403,

1

C7

Desolder

[18]

DVD MECHA

C6

—

—

[19]

POWER CBA ASSEMBLY

C8

4(S-10), Insulation Sheet

—

1

 : Identification (location) No. of parts in the figures

2

 : Name of the part

3

 : Figure Number for reference

4

 : Identification of parts to be removed, unhooked, unlocked,

released, unplugged, unclamped, or desoldered.
P=Spring, L=Locking Tab, S=Screw,
CN=Connector,
*=Unhook, Unlock, Release, Unplug, or Desolder
e.g. 5(S-1) = five Screws (S-1),

2(L-2) = two Locking Tabs (L-2)

5

 : Refer to "Reference Notes."

↑

↑

↑

↑

↑

1

2

3

4

5

CAUTION 1: When reassembling, connect the motor cable to

the Main CBA assembly correctly as shown in
Fig. C7.

– 12 –

(S-1)

(S-2)

(S-2)

Fig. C1

[1]  TOP 
CABINET

[2]  BOTTOM 
CABINET

(S-2)

(S-2)

(L-1)

(S-4)

(S-3)

(S-3)

Fig. C2

[3]  TOP 
SUPPORT 
ANGLE

[4]  FRONT UNIT

(S-5)

(S-6)

(S-6)

(S-5)

(L-2)

Fig. C3

CN2001

[5]  FRONT 
ANGLE

[7]  FRONT 
CBA UNIT

[6]  PWB SPACER

(L-4)

(L-3)

(L-3)

Fig. C4

[8]  LCD

[9]  DIFFUSION SHEET 

[10]  LIGHITING PLATE

[11]  REFLECTION SHEET

[12]  LCD HOLDER

[13]  FRONT CBA  
ASSEMBLY

Desolder (from rear side)

(S-7)

(S-8)

(S-8)

(L-5)

(L-5)

Fig. C5

CN1001

CN1002

CN1003J

[16]  TRAY 
PANEL

[14]  BACK PLATE

[15]  DVD MECHA UNIT

Jack Angle

Erase
Plate