DOWNLOAD Sharp DV-RW360H (serv.man10) Service Manual ↓ Size: 12.13 MB | Pages: 100 in PDF or view online for FREE

89

EN

This feature allows you to go 
to a specific point on a tape by 
entering the exact amount of 
time you wish to skip in order to 
reach the point.

1

2

3

6

5

4

7

0

+10

8

9

STOP

PLAY

VCR

DVD

Press      first.

  TIME    2:50

Press [FWD D / q] or [REV 
E

 / r] to start time search.

If you want to go in the forward 
direction, press [FWD D / q].
If you want to go in the reverse 
direction, press [REV E / r].
After time search, the unit will 
play the tape automatically.

AUDIO

REPEAT

PAUSE

SEARCH

SLOW

MENU LIST

TOP MENU

STOP

PLAY

FWD

REV

SKIP

PROG.

CLEAR/C-RESET

VCR

REC/OTR

DVD

REC/OTR

PQRS

TUV

WXYZ

GHI

JKL

MNO

.@/:

ABC

DEF

SPACE

DISPLAY

ENTER

ZOOM

REC MODE

VCR

RAPID PLAY

DVD

CM SKIP

SETUP

T-SET

    OPEN/CLOSE

EJECT

TIMER PROG.

DUBBING

RETURN

OPERATE

1

2

3

6

5

4

7

0

+10

8

9

STOP

PLAY

VCR

DVD

Press      first.

  INDEX    03

Press [FWD D / q] or [REV 
E

 / r] to start index search. 

If you want to go in the forward 
direction, press [FWD D / q].
If you want to go in the reverse 
direction, press [REV E / r].
After index search, the VCR will 
play the tape automatically.

Pro.1

Pro.2

Pro.3

Pro.4

Pro.5

02

01

01

02

03

Beginning 
of tape

End 
of tape

CURRENT PROGRAM

INDEX MARK

•  This function is not available during recording.
•  Every time a tape is recorded, an index mark is written on the tape.
•  You can make the index mark up to 20.

•  This function is not available during recording.
• Press [STOP C] to stop the search.
•  If the tape reaches the end during the search, this unit will cancel it 

and rewind the tape.

•  You can set the time up to 9:59.

AUDIO

REPEAT

PAUSE

SEARCH

SLOW

MENU LIST

TOP MENU

STOP

PLAY

FWD

REV

SKIP

PROG.

CLEAR/C-RESET

VCR

REC/OTR

DVD

REC/OTR

PQRS

TUV

WXYZ

GHI

JKL

MNO

.@/:

ABC

DEF

SPACE

DISPLAY

ENTER

ZOOM

REC MODE

VCR

RAPID PLAY

DVD

CM SKIP

SETUP

T-SET

    OPEN/CLOSE

EJECT

TIMER PROG.

DUBBING

RETURN

OPERATE

90

EN

This unit will record and playback Hi-Fi stereo sound. In addition, it 
has an AV2 and NICAM stereo sound decoder.
This unit will receive stereo and bilingual broadcasts and it is possible 
to record in several ways and to play back the sound.
Selecting the Sound Mode
You can select each mode by pressing [AUDIO] on the remote 
control. Each mode is indicated on the TV screen as following.
•  During playback of the recorded tape in Hi-Fi mode
•  During reception of stereo broadcasts

Stereo

Stereo

STEREO

L

L audio from both speakers

LEFT

R

R audio from both speakers

RIGHT

Normal

Monaural

-None-

•  During reception of bilingual broadcasts

Main

Main audio from both speakers

Main

Sub

Sub audio from both speakers

Sub

Main / Sub

•  Main audio from the left speaker
•  Sub audio from the right speaker

Main / Sub

•  If you play back non-Hi-Fi 

tapes, the unit will play back 
automatically in monaural 
even if you select any mode.

•  If the stereo signal becomes 

weak, the broadcast is 
automatically recorded in 
monaural.

1

2

3

6

5

4

7

0

+10

8

9

STOP

PLAY

VCR

DVD

Press      first.

To cue or review picture during playback (Picture Search):
Press [FWD D / q] or [REV E / r] during playback.
Press it again and the unit will search in super high speed.
To freeze the picture on TV screen during playback (Still mode):
Press [PAUSE F]. Each time you press the button, the picture will be 
forwarded frame by frame.
If the picture begins to vibrate vertically during the still mode, 
stabilize the picture by pressing the [PROG. 

].

If the picture is distorted or rolling vertically, adjust the vertical hold 
control on your TV, if equipped.
Counter Reset:
Press [CLEAR/C-RESET].
To play back in slow motion:
Press [SLOW  ] during playback or the still mode.
If the noise bars appear on the TV screen, you can reduce it by 
pressing [PROG. 

].

•  Still / Slow / Pause mode will 

be automatically cancelled 
after 5 minutes to prevent 
damage to the tape and the 
video head.

•  To return to play back from 

the Picture Search / Still / Slow 
mode, press [PLAY B].

91

EN

The power does not turn on.

• Check the mains cable is connected securely.
• Check the breaker (in case of power failure).

Any of the buttons on the front 
panel does not function.

• Check if the Child Lock is activated. (See page 10.)

There is no picture.

• Check signal cables are connected securely.
• Check if a connecting cable is damaged.
• Check connections to your TV. (See pages 14-15.)
• Switch the input selector on your TV (to “AV1” for example) until a picture 

appears on the screen.

The picture on your TV is distorted 
during the unit is turned on.

• Turn the unit off if the unit is not being used.
• Change the channel on this unit.

TV programme picture does not fill 
the screen.

• Set channels with “Auto Tuning” from the Setup menu. (See page 19.)
• Select the channel of a TV programme using [PROG.   /  ].

TV programme pictures are 
distorted.

• Adjust the direction of the TV antenna.
• Adjust the picture. (See the TV instruction manual.)
• Place the antenna and the TV farther apart.
• Separate any bunched antenna cables and the TV.

TV channel cannot be changed.

• Switch the TV input.
• Check if the antenna cable is connected correctly. (See pages 14-15.)

The channel cannot be changed 
from the channel you are 
recording.

• Set the TV input to “TV”.

Playback picture is distorted.

• Do not bring equipment that may cause electrical interference, such as a 

cellular phone, near the unit.

The playback picture or TV 
programme from equipment 
connected through the unit is 
distorted.

• If a DVD player, VCR or tuner is connected to your TV via the unit, the 

copyprotection signal applied to some programmes could affect picture 
quality. Disconnect the playback equipment in question and connect it 
directly to your TV.

Nothing was recorded even 
though you set the timer setting 
correctly.

• There was a power failure during recording.
• The unit’s internal clock stopped due to a power failure that lasted for more 

than 1 hour.

• Reset the clock. (See page 22.)
• Unplug the mains cable from the AC outlet and plug it in again.
• The programme contains copy protection signals that restrict copying.
• The timer setting overlapped with another setting that was set later or has priority.

WARNING
Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do 
not open the system as there is a risk of electric shock.
If a fault occurs, first check the points listed below before taking the system for repair.

The following conditions do not always denote trouble. Therefore, perform the checks described below 
before calling for service. If the problem cannot be corrected by the use of this guide, remove the main 
plugs from the wall socket, and contact the dealer or supplier from whom the unit was purchased in order 
to obtain service. Where this is not possible please visit our web-site
www.sharp.co.uk/customersupport.
Customers without Internet access may telephone 08705 274277 during office hours (or (01) 6760648 if 
telephoning from Ireland), Certain replacement parts and accessories may be obtained from our main 
parts distributor, who can be contacted on the following numbers:

WILLOW VALE ELECTRONICS LTD.:

0121 766 5414

In the unlikely event of this equipment requiring repair during the guarantee period, you will need to 
provide proof of the date of purchase to the repairing company. Please keep your invoice or receipt, 
which is supplied at the time of purchase.

92

EN

There is no picture.

• If the Setup menu display appears, press [SETUP] or [RETURN 

] to turn off 

the display.

Picture noise appears.

• The disc is dirty or flawed.
• If the unit is connected to your TV via a VCR, or if it is connected to a 

combination TV / VIDEO player, the copy-protection signal applied to some 
DVD programmes could affect picture quality. If you still experience this 
problem even when you connect the unit directly to your TV, try connecting 
the unit to your TV’s S-VIDEO input.

Sound is noisy.

• The disc is dirty or flawed.

The unit does not play back the 
disc.

• No disc is inserted.
• A blank disc is inserted.
• The disc is upside down. Insert the disc with the labelled side facing up.
• The disc is not correctly inserted.
• The unit cannot play back certain discs (such as a CD-ROM). (See page 42.)
• The region codes on the DVD-Video and the unit are not matched. (See page 42.)
• Moisture has condensed inside the unit. Remove the disc and leave the unit 

turned on for about two hours until the moisture evaporates. (See page 3.)

• The unit cannot play back the disc if it was recorded on another recorder and 

not finalised.

There is no sound.

• If the audio signal is not output from the DIGITAL AUDIO OUT (COAXIAL) 

jack, check the Audio setting. (See pages 81-83.)

Playback image freezes for a 
moment.

• During the playback of a two layered disc, the picture may freeze for a 

moment while playback switches from the first to the second layer. This is 
not a malfunction.

The unit does not play back the 
disc from the beginning.

• Resume playback is activated. (See page 49.) Press [STOP C] twice.
• You have inserted a disc whose Title menu or DVD menu automatically 

appears on the TV screen when it is first inserted.

The unit starts playing back the 
disc automatically.

• The DVD-Video features an auto playback function.

Timer recording is not completed 
or did not start from the 
beginning.

• The timer setting overlapped with another setting that has priority. 

(See page 34.)

• There was not enough disc or tape space.

There is no sound.

• The disc is dirty or flawed.
• Check if all cables are connected securely.
• Check if a connecting cable is damaged.
• Check the connections to the amplifier input.
• Check if the input source setting on the amplifier is correct.
• Check if the unit is in Pause mode or in Slow-motion Playback mode.
• Check if the unit is in Fast Forward or Fast Reverse mode.

Timer recording is not possible.

• Make sure   icon appears on the front panel display of this unit. If not, press 

[T-SET].

The remote control does not 
function.

• Batteries are exhausted.
• There are obstacles between the remote control and the unit.
• The remote control is too far from the unit.
• There are no batteries in the remote control.
• The unit is not turned on.
• The remote control is not pointed at the remote sensor on the unit.
• Check if the Child Lock is activated. (See page 10.)
• Press [VCR] or [DVD], whichever you need. Then, try again.

The unit does not operate 
correctly.

• If static electricity or anything else causes the unit to operate abnormally, 

unplug the mains cable and plug it in again.