View Sharp DV-RW360H (serv.man10) User Guide / Operation Manual online
using your VCR/DVD RECORDER COMBINATION.
this unit is 2.
Sharp product, please visit our web-site
08705 274277 during office hours
(or (01) 6760648 if telephoning from Ireland).
USE OF CONTROLS OR ADJUSTMENTS OR
AS THE LASER BEAM USED IN THIS UNIT IS
This unit can be used only where the power supply is
AC 220–240V ~ ± 10%, 50Hz ± 0.5%. It cannot be used
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,
against electric shock, fire or personal injury, please
observe the following.
• Hold the plug firmly when connecting or disconnecting
• Never put any heavy object on the AC power cord.
• Do not bundle any cables such as; AC power cord,
connect this unit to your TV together. Or never put
any cables on the top panel of this unit. The noise or
disturbance of the picture may be generated.
• The CLASS 1 LASER PRODUCT marking is embossed on
continued safety, do not
remove any cover or attempt
to gain access to the inside of
the product. Refer all
servicing to qualified
CLASSE 1 PRODUIT LASER
PRODUCT CON LASER CLASE 1
Read carefully the information located at the bottom
of your unit and enter below the Serial No. Retain this
information for future reference.
Serial No.: __________________________________
rewireable (moulded) plug incorporating a 3A fuse.
Should the fuse need to be replaced, a BSI or ASTA
approved BS 1362 fuse marked or
the plug, must be used. Always refit the fuse cover after
replacing the fuse. Never use the plug without the fuse
cover fitted. In the unlikely event of the socket outlet in
your home not being compatible with the plug supplied,
cut-off the mains plug and fit an appropriate type.
immediately and disposed of in a safe manner.
Under no circumstances should the cut-off
plug be inserted elsewhere into a 13A socket
outlet, as a serious electric shock may occur.
To fit an appropriate plug to the mains lead,
follow the instructions below:
the mains lead are coloured
in accordance with the
in the mains lead of this product may not correspond
with the coloured markings identifying the terminals in
your plug, proceed as follows:
- The wire which is coloured blue must be connected to
connected to the earth terminal in your three-pin plug.
Before replacing the plug cover make sure that:
- If the new fitted plug contains a fuse, its value is the
“Dolby” and the double-D symbol are trademarks of
“Dolby® Digital Recording enables consumers to record
high-quality video with stereo sound on recordable
DVD discs. The technology, when utilized instead
of PCM recording, also saves recordable disc space,
allowing for higher video resolution or extended
recording time on each DVD. DVDs created using
Dolby Digital Recording will play back on all DVD-Video
Note: This is true when the players are compatible with
actual recordable DVD discs.
Theater Systems, Inc.
Eastman Kodak Company.
logos are trademarks of DivX, Inc. and
are used under license.
consent. Please refer particularly to the provisions of the
copyright Act 1956, the Dramatic and Musical Performers
Protection Act 1958, the Performers Protection Acts 1963
and 1972 and to any subsequent statutory enactments
On DVD discs that include a copy protection code, if the
contents of the DVD disc are copied using a VCR, the
copy protection code prevents the videotape copy from
5,315,448; and 6,516,132.
technology that is protected by U.S. patents and other
intellectual property rights. Use of this copyright
protection technology must be authorised by
Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorised
by Macrovision. Reverse engineering or disassembly is
• Immediately after a heater is turned on.
• In a steamy or humid room.
• When the unit is suddenly moved from a cold to warm
not operate properly or damage the video tape. In such
case, turn on the power and wait for more than 2 hours
for the moisture to evaporate.
the cassette compartment.
directly on top of the unit. Do not place the unit directly
on top of the TV.
placed too close to your TV. In this case, please ensure
enough space between your TV and the unit.
device (candles, etc.).
• Do not place any object containing water or other
the cabinet, unplug the unit immediately and contact
the retailer or service centre approved by SHARP
damage to the unit. For service and adjustment inside
the cabinet, call a qualified dealer or service centre
approved by SHARP.
• Read both manual instructions to ensure correct and
activate and the protected material will not be recorded
correctly. In addition, attempting to display copy
protected material on a monitor connected via a VCR,
whether for the purpose of viewing or not, will cause an
inferior quality picture to be displayed. This is not a fault
of the equipment. Please view copy protected material
by connecting the product directly to the monitor.
extremely accurate technology.
• The disc cannot be played if the disc drive component is
on page 91, the laser optical pickup unit may be dirty.
Consult a SHARP Approved Service Centre for inspection
and cleaning of the laser optical pickup unit.
can impair the image quality. At the worst, neither video
nor audio will be played back. To maintain optimum
picture quality, the Player should be serviced (cleaned
and replacement of some parts) every 1,000 hours. Note
that this period varies depending on the environment
(temperature, humidity, dust, etc.) in which the unit is
used. Contact your authorised SHARP supplier for details.
accumulated on the video heads after a long period of
use, or the usage of rental or worn tapes can cause this
problem. If a streaky or snowy picture appears during
playback, the video heads in your unit may need to be
television sets are fully compatible with this product
and may cause artifacts to be displayed in the picture.
In case of picture problems with 525 or 625 progressive
scan output, it is recommended that the user switch the
connection to the ‘standard definition’ output. If there are
questions regarding your TV set compatibility with this
525p or 625p DVD player, please contact our customer
Broadcast Is Being Received
interference may appear on the TV monitor while you
watch a TV broadcast and the unit is left on. This is
not a malfunction of the unit or the TV. To watch a TV
broadcast, turn off the unit.
5,214,678, 5,323,396, 5,530,655, 5,539,829, 5,544,247,
5,606,618, 5,610,985, 5,740,317, 5,777,992, 5,878,080, or
Centre for inspection.
parts may cause fire, electrical shock, or other hazards.
unit is in safe operating order.
spirits, ammonia or abrasive.
a circular motion.
cleaning agents or antistatic spray intended for