DOWNLOAD Sharp XL-UH240H Service Manual ↓ Size: 2.77 MB | Pages: 44 in PDF or view online for FREE

 

XL-UH240H

XL-UH240H

Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS socket and position
the FM aerial wire in the direction where the strongest signal can be
received.

Supplied AM loop aerial:
Connect the AM loop aerial to the AM and Earth (GND) terminals.
Position the AM loop aerial for optimum reception. Place the AM loop
aerial on a shelf, etc., or attach it to a stand or a wall with screws (not
supplied).

Note:
Placing the aerial on the unit or near the AC power lead may cause
noise pickup. Place the aerial away from the unit for better reception.

  

 

Connect the black wire to the minus (-) terminal, and the red wire to
the plus (+) terminal.

  

 

< Assembling >

< Attaching to the wall >

 

Wall   Screws (not supplied)

  

Use speakers with an impedance of 6 ohms or more, as lower 
impedance speakers can damage the unit.

  

Do not mistake the right and the left 
channels. The right speaker is the one on the 
right side when you face the unit.

  

  

Do not allow any objects to fall into or to be 
placed in the bass reflex ducts.

  

Do not stand or sit on the speakers. You may 
be injured.

Make sure nothing comes into contact 
with the speaker diaphragm when you 
remove the speaker grilles.

Black

Red

 

XL-UH240H

  

 

After checking all the connections have been made correctly, plug
the AC power lead of this unit into the wall socket. If you plug in the
unit first, the unit will enter the demonstration mode.

  

Unplug the AC power lead from the wall socket if the unit will not
be in use for a prolonged period of time.

  

 

 

  

 

Use an external FM aerial if you require better reception.
Consult your dealer.

 

When an external FM aerial is used, disconnect the supplied FM
aerial wire.

 

The main unit is built with a cooling fan at the rear of the unit for im-
proved cooling. Please do not cover the opening of the fan with any 
obstacles, as this will block proper ventilation.

 

The first time the unit is plugged in, the 
unit will enter the demonstration mode. 
You will see words scroll.

 

When the unit is in the power stand-
by mode (demonstration mode),
press the  X-BASS/DEMO button on
the remote control. The unit will
enter the low power consumption
mode.

 

When the unit is in the power stand-by mode, press the X-BASS/
DEMO button on the remote control again.
 

 

When the power is on, the  X-BASS/DEMO button can be used to 
select the extra bass mode.

External
FM aerial

75 ohms
coaxial cable

 

XL-UH240H

  

 

 

  

Replace all old batteries with new ones at the same time.

  

Do not mix old and new batteries.

  

Remove the batteries if the unit will not be used for long periods
of time. This will prevent potential damage due to battery leakage.

  

Do not use rechargeable batteries (nickel-cadmium battery, etc.).

  

Installing the batteries incorrectly may cause the unit to
malfunction.

 

Open the battery cover and pull up the battery to take out. 

  

Replace the batteries if the operating distance is reduced or if the
operation becomes erratic.

  

Periodically clean the transmitter on the remote control and the
sensor on the unit with a soft cloth.

  

Exposing the sensor on the unit to strong light may interfere with
operation. Change the lighting or the direction of the unit if this
occurs.

  

Keep the remote control away from moisture, heat, shock, and
vibrations.

 

  

 

Check the remote control after checking all the connections (see
pages 9 - 11).
Point the remote control directly at the remote sensor on the unit.

 

Press the ON/STAND-BY button. Does the power turn on? Now, you
can enjoy music.

Use 2 "AA" size batteries (UM/SUM-3, R6, HP-7 or similar).

Batteries are not included.

 

 

When inserting or removing the batteries, push them towards the 

 battery terminals.