Sharp XL-560E (serv.man2) Service Manual ▷ View online
– 13 –
XL-560H/E,570H/E
If the following buttons are pressed in this state, the operation is performed as follows.
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
is invalid.
"PLAY" ..................... Shift to step 3
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
2. Step 2 Mode
When the "PLAY" button is pressed in this mode, the laser lighting command LDON (8400) is sent, and the laser is turned on.
Other operations are not performed.
When the "PLAY" button is pressed in this mode, the laser lighting command LDON (8400) is sent, and the laser is turned on.
Other operations are not performed.
2. CD Test Mode (TEST 1)
In the CD test mode the operation of each step is enabled even when the LID-SW is off. However, if focus cannot be set in step
3 or any error processing is started, it is impossible to proceed to the next step. When the error processing is started, operations
other than termination of test mode by pressing the POWER button or return to the step 1 by pressing the STOP button are inhibited.
In the CD test mode the operation of each step is enabled even when the LID-SW is off. However, if focus cannot be set in step
3 or any error processing is started, it is impossible to proceed to the next step. When the error processing is started, operations
other than termination of test mode by pressing the POWER button or return to the step 1 by pressing the STOP button are inhibited.
1. Step 1 Mode
When the CD test mode is turned on, the following indication lights, the processing (until turning-off of CD STB terminal of CD
initialization operation flow) is executed, and the next button input is waited.
When the CD test mode is turned on, the following indication lights, the processing (until turning-off of CD STB terminal of CD
initialization operation flow) is executed, and the next button input is waited.
After lighting for one second
If the following operation buttons are pressed in this state, the operation is performed as follows.
"POWER" ................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................. After the pickup returns once to the innermost periphery, it slides toward the outer periphery while this
"FF/FWD" ................. After the pickup returns once to the innermost periphery, it slides toward the outer periphery while this
button is held down.
"REW/REV" .............. After the pickup returns once to the innermost periphery, it slides toward the inner periphery while this
button is pressed. However, if PU-IN is on, input is invalid.
"PLAY" ..................... Shift to step 2
"STOP" ..................... Invalid
"REC PAUSE" .......... Shift to step 5
"STOP" ..................... Invalid
"REC PAUSE" .......... Shift to step 5
* In case of initialization the pickup is moved toward the inner periphery. Any buttons other than "POWER" button are not
accepted until the shift of pickup to the inner periphery is completed at this time. If PU-IN SW ON cannot be detected within
10 seconds, the slide motor is stopped, and the following error indication appears. Press the POWER button to end the test
mode, or press the STOP button to return to step 1. Any other operations are inhibited.
10 seconds, the slide motor is stopped, and the following error indication appears. Press the POWER button to end the test
mode, or press the STOP button to return to step 1. Any other operations are inhibited.
XL-560H/E,570H/E
– 14 –
When the following operation buttons are pressed in this sate, the operation is executed as follows.
"POWER" ................. The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................. The pickup slides toward the outer periphery while this button is held down.
"REW/REV" .............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
"FF/FWD" ................. The pickup slides toward the outer periphery while this button is held down.
"REW/REV" .............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
is invalid.
"PLAY" ..................... Invalid
"STOP" ..................... Return to step 1
"FUNCTION" ............ Shift to step 6
"BAND" .................... Shift to step 7
"STOP" ..................... Return to step 1
"FUNCTION" ............ Shift to step 6
"BAND" .................... Shift to step 7
*If the focus is disturbed, the process returns to step 1.
Other cautions
• TOC IL is not executed in the test mode.
• As for button operations other than those shown above, only the sound volume operation (with JOG) is accepted.
• TOC IL is not executed in the test mode.
• As for button operations other than those shown above, only the sound volume operation (with JOG) is accepted.
5. Step 5 Mode
The CD initialization operation flow is executed to the end, the mute is set to off, and playback is started. Even when the
playback reaches the outermost periphery of disc, the operation does not stop. The LCD display indicates the playback past
time as in case of ordinary CD playback.
playback reaches the outermost periphery of disc, the operation does not stop. The LCD display indicates the playback past
time as in case of ordinary CD playback.
The time display indicates always "0:00".
When the following buttons are pressed in this state, the operation is executed as follows.
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
is invalid.
"PLAY" ..................... Shift to step 5
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
*If the focus is disturbed, the process returns to step 1.
4. Step 4 Mode
The CLV servo ON command (8600) sending operation is performed, and the next button input is waited. (The disc is rotated
to perform CLV locking.)
to perform CLV locking.)
When the following operation buttons are pressed in this state, the operation is executed as follows.
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
"POWER" ................ The test mode is turned off, the power is turned off, and the ordinary standby mode is set.
"FF/FWD" ................ The pickup slides toward the outer periphery while this button is held down.
"REW/REV" ............. The pickup slides toward the inner periphery while this button is held down. However, if PU-IN is on, input
is invalid.
"PLAY" ..................... If the focus has been set, shift to step 4 is executed. If the focus has not been set, acceptance is inhibited.
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
*If the focus is disturbed after it has been set, the process returns to step 1.
"STOP" .................... Return to step 1
"REC PAUSE" ......... Shift to step 5
*If the focus is disturbed after it has been set, the process returns to step 1.
3. Step 3 Mode
The laser is kept lighting. The processing (until turning-on of CLV servo of CD initialization operation flow) is executed, and
the next button input is waited. (The focus servo is turned on, and focus search is performed.)
The focus search is repeated until the focus is set.
the next button input is waited. (The focus servo is turned on, and focus search is performed.)
The focus search is repeated until the focus is set.
– 15 –
XL-560H/E,570H/E
3. Tuner Test Mode (TEST 2)
1. Outline of tuner (radio) test mode
The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH without
The tuner test mode is intended to store the adjustment and measurement frequencies in the preset memory CH without
frequency setting by adjusting personnel when the tuner section is adjusted in the production line.
2. Details of tuner test mode
When the power is turned on by using the "POWER" button while the "FF/FWD" and "MEMORY/SET" buttons are held down
When the power is turned on by using the "POWER" button while the "FF/FWD" and "MEMORY/SET" buttons are held down
in POWER OFF state, the frequency for adjustment and measurement of destination specified by the AREA terminal is preset
and stored in the preset memory CH. However, Ordinary 1 and Ordinary 2 are set to the designation (destination selected
by SPAN switching operation) set when the test mode is set. (As for frequencies to be preset and stored for each destination,
refer to item 3.)
and stored in the preset memory CH. However, Ordinary 1 and Ordinary 2 are set to the designation (destination selected
by SPAN switching operation) set when the test mode is set. (As for frequencies to be preset and stored for each destination,
refer to item 3.)
The tuner test mode is started from preset No.1.
The operations of test mode are identical with the ordinary operations of TUNER function. However, FUNCTION switching
The operations of test mode are identical with the ordinary operations of TUNER function. However, FUNCTION switching
is invalid.
Since it is necessary to discard the content of preset memory when the tuner test mode is ended, "0000" or "1111" bits are
written in the memory to be checked in case of memory check (in case of initial setting) so that memory abnormality is detected
in case of initial setting so as to ensure memory initialization.
in case of initial setting so as to ensure memory initialization.
When the tuner test mode is turned on, the following indication lights for one second.
• The TUNER TEST2 mode is set as a result of >> + MEMORY + POWER. -> IF AC is set to OFF in the TEST2 mode, the initial
state is restored.
When POWER is set to OFF, the memory of TEST2 mode is protected.
When the power is turned on again, the ordinary operation is enabled while the data is stored in the
memory (besides TUNER).
When the power is turned on again, the ordinary operation is enabled while the data is stored in the
memory (besides TUNER).
If AC OFF state is maintained in this state for about 1/2 day, start is executed in the initial state.
• To clear the whole memory, insert the AC cord, holding down MEMORY + BASS/TREBLE.
3. Preset frequencies for various destinations (random preset memory)
• The hatched sections of the table are not stored in memory.
BAND
16
17
18
19
20
17
18
19
20
21
22
23
24
25
22
23
24
25
26
FM106.00 MHz
27
FM 90.00 MHz
28
FM MONO
FM 98.00 MHz
29
FM108.00 MHz
30
FM 87.50 MHz
Europe 2, 4
CH
BAND
1
FM 87.50 MHz
2
FM108.00 MHz
3
FM STEREO
FM 98.00 MHz
4
FM 90.00 MHz
5
FM106.00 MHz
6
AM 522 kHz
7
AM1620 kHz
8
AM
AM 990 kHz
9
AM 603 kHz
10
AM1404 kHz
11
12
13
12
13
LW
14
15
15
Europe 2, 4
CH
XL-560H/E,570H/E
– 16 –
4. ASPM TEST Mode (RDS circuit is only for XL-560H/570H)
When the ASPM button is pressed, the test mode is set. It starts up at FM 106.50 MHz. (ST mode)
Data of 27 CH of 04 to 30 CH are all stored at FM 87.50 MHz (ST).
01 to 03CH are kept empty (If data of 3 CH are stored, max. 30 CH is filled.)
When the ASPM button is operated in the TEST mode 3, the preset data is cleared (overwrite).
01 to 03CH are kept empty (If data of 3 CH are stored, max. 30 CH is filled.)
When the ASPM button is operated in the TEST mode 3, the preset data is cleared (overwrite).
A) Operation with ASPM button
Press the "ASPM" button or hold it down. (Any button other than ASPM button cancels the ASPM test mode.)
Press the "ASPM" button or hold it down. (Any button other than ASPM button cancels the ASPM test mode.)
FM 105.00 MHz (ST) is indicated, and scan is started.
(Start from 105.00 MHz)
(Start from 105.00 MHz)
During scanning the frequency is indicated.
End at FM 108.00 MHz (ST)
Only the number of preset and stored stations (number of CHs: max. 3 stations) is indicated for one second in the ASPM test
mode. When two stations are stored, "_2 MEMORY" is indicated (lighted)for one second.
("02 MEMORY" indication is not given.)
mode. When two stations are stored, "_2 MEMORY" is indicated (lighted)for one second.
("02 MEMORY" indication is not given.)
"END" is not indicated
01CH indication (for one second)
Frequency indication (for one second)
02CH indication (for one second)
Frequency indication (for one second)
03CH indication (for one second)
Frequency indication (for one second)
After indication of continuous time series for one second the indication of FM 106.50 MHz (ST) is restored.
(The preset button is not pressed. The time series is indicated automatically, and the content of memory is indicated.)
(The preset button is not pressed. The time series is indicated automatically, and the content of memory is indicated.)
* PS name is not indicated (while the content of memory is checked)
* If only 1 CH data is stored, FM P-01 -> FM 106.00 MHz -> FM 106.50 MHz (ST)
(An example) (1 sec) (1 sec) (ST) End indication
* If only 1 CH data is stored, FM P-01 -> FM 106.00 MHz -> FM 106.50 MHz (ST)
(An example) (1 sec) (1 sec) (ST) End indication
When the ASPM button is pressed once in the TUNER TEST
mode, the indication FM 106.50 MHz (ST) appears, and data
of 04 to 30 CH are stored at 87.50 MHz (ST). When the ASPM
button is operated again, the ASPM test operation mode is
set.
mode, the indication FM 106.50 MHz (ST) appears, and data
of 04 to 30 CH are stored at 87.50 MHz (ST). When the ASPM
button is operated again, the ASPM test operation mode is
set.
In case of "_0 MEMORY" the process ends, and the
FM 106.50 MHz (ST) state is resumed.
FM 106.50 MHz (ST) state is resumed.
Confirmation of content of memory
(Examples of concrete indication)
(Examples of concrete indication)
(An example)
FM P-01
FM P-01
FM 105.50MHz(ST)
FM P-02
FM 106.50MHz(ST)
FM P-03
FM 107.50MHz(ST)
Not in zero-memory state
Click on the first or last page to see other XL-560E (serv.man2) service manuals if exist.