Sharp XL-3500 (serv.man20) Service Manual ▷ View online
– 17 –
XL-3500H
4. Electronic volume Test Mode (TEST 3)
When this test mode is obtained, the following display lights for one second.
In this mode, volume is -14 dB (STEP28), BASS/TREBLE is set to 0 (0 dB) and SURROUND mode to OFF, and start-up function
to CD, respectively. The button operations in the test mode are the same as those of ordinary operation except volume UP/
DOWN.
to CD, respectively. The button operations in the test mode are the same as those of ordinary operation except volume UP/
DOWN.
(1) The display is the same as that of ordinary operation except test mode setting.
(2) Unlike the ordinary state, the volume is controlled with the volume UP/DOWN button in accordance with the following three
(2) Unlike the ordinary state, the volume is controlled with the volume UP/DOWN button in accordance with the following three
steps.
Volume-
∞
(STEP 0) <-> Volume-14 dB (STEP 23) <-> Volume-0 (STEP 30)
(3) BASS/TREBLE and SURROUND are switched when button is pressed..
Set the current time and timer time according to the following procedure to reproduce the timer.
1.Set the current time to 1:00, the timer to ON time 1:05, the function to CD, and volume to STEP 12, respectively. One minute
is counted as one second, and the timer is reproduced. The fade-in (when playback is started) is executed at a rate of one step
for 1 sec. After completion of fade-in, the fade-out is executed at a rate of one step for 1 sec (WAIT 1 sec inserted).
for 1 sec. After completion of fade-in, the fade-out is executed at a rate of one step for 1 sec (WAIT 1 sec inserted).
After completion of fade-out, the power is turned off (after WAIT 1 sec), and the mode is shifted to the standby.
The display during operation is the same as that of ordinary timer operation.
The display during operation is the same as that of ordinary timer operation.
5. Timer test Mode (TEST 4)
When this test mode is obtained, the following display lights for one second.
6. LCD Test Mode (TEST 5)
When the LCD test mode is obtained, all the LCD segments are lighted. Then pressing the "PLAY" button switches display as
below.
below.
Lighting of all segments Lighting of odd segments Lighting of even segments
XL-3500H
– 18 –
This test mode is intended to check whether all the main unit buttons can be detected. Accordingly, in this test mode, it is checked
whether the "ON/STAND-BY" button was pressed after all the buttons shown below were pressed. If the result is OK, OK is
displayed. If any one of keys was not pressed, an error is displayed. In both cases of OK termination or error termination, the
mode is shifted to the standby mode if the "ON/STAND-BY" button is pressed subsequently.
whether the "ON/STAND-BY" button was pressed after all the buttons shown below were pressed. If the result is OK, OK is
displayed. If any one of keys was not pressed, an error is displayed. In both cases of OK termination or error termination, the
mode is shifted to the standby mode if the "ON/STAND-BY" button is pressed subsequently.
All models using this type of microcomputer are not always provided with the same buttons. Since the buttons used are different
depending on models, types of buttons to be used are determined by whether RDS, SURROUND, and an electric lid are
available at the initial setting by MODEL port.
depending on models, types of buttons to be used are determined by whether RDS, SURROUND, and an electric lid are
available at the initial setting by MODEL port.
The order of buttons to be pressed is not determined. Accordingly, it is checked whether all buttons have been pressed.
1. PU-IN buttons: REW/PRESET DOWN + CD STOP
Since this model is provided with SURROUND (HAVE OR NOT), RDS (HAVE OR NOT), and electric CD lid, the following
10 buttons are detected as all buttons.
PLAY, BASS/TREBLE, FUNCTION, VOLUME UP/DOWN, MEMORY/SET, REW, FF, STOP, CD-OPEN/CLOSE
10 buttons are detected as all buttons.
PLAY, BASS/TREBLE, FUNCTION, VOLUME UP/DOWN, MEMORY/SET, REW, FF, STOP, CD-OPEN/CLOSE
The OK/NG display of test result is as follows.
7. Button input diagnosis Test Mode (TEST 6)
When the test mode is obtained, the following is displayed.
a. POWER ON for function AUX
CD lid position is checked.
CLOSE position: Operation proceeds to the next process.
Position other than CLOSE: After the lid moves to CLOSE, operation proceeds to the next process.
Position other than CLOSE: After the lid moves to CLOSE, operation proceeds to the next process.
b. CD lid operation started
OPEN operation
WAIT 1 second
CLOSE operation
WAIT 1 second
CLOSE operation
WAIT 1 second
c. Operations above are repeated.
Specified monitoring time
OPEN operation: 5 seconds
CLOSE operation: 5 seconds
CLOSE operation: 5 seconds
8. Electric CD lid Aging Test Mode (TEST 8) (Only for model with electric CD lid)
Outline
OPEN/CLOSE operations of electric CD lid are repeated. The number of repeated times and time period are monitored. If the
lid does not move to the regular position after the specified time, operation is stopped. When an error is detected by [CLID_PRO]
during CLOSE, operation is also stopped.
OPEN/CLOSE operations of electric CD lid are repeated. The number of repeated times and time period are monitored. If the
lid does not move to the regular position after the specified time, operation is stopped. When an error is detected by [CLID_PRO]
during CLOSE, operation is also stopped.
d. Display
OPEN>CLOSE is counted as 1. 1 to 59999 are counted; if the count is over
59999, display is returned to 0 to repeat counting.
59999, display is returned to 0 to repeat counting.
Display when the lid does not move to the regular position after the specified
time
(Ex: Defective operation occurring in the middle of 1538.)
time
(Ex: Defective operation occurring in the middle of 1538.)
Highlight display of stop when an error is detected by [CLID-PRO]
(Ex: Defective operation occurring in the middle of 1538.)
(Ex: Defective operation occurring in the middle of 1538.)
– 19 –
XL-3500H
SW702
PICKUP IN
ON—OFF
SW709
ON/STAND-BY
ON—OFF
SW710
CD LID OPEN/CLOSE
ON—OFF
SW711
REW/PRESET DOWN
ON—OFF
SW712
FF/PRESET UP
ON—OFF
SW713
CD STOP/TUNING DOWN
ON—OFF
SW718
CD PLAY/PAUSE/TUNING UP
ON—OFF
•
The indicated voltage in each section is the one measured
by Digital Multimeter between such a section and the chas-
sis with no signal given.
1. In the tuner section,
sis with no signal given.
1. In the tuner section,
( ) : AM mode
: FM stereo mode
2. In the CD section, the CD is stopped.
•
Parts marked with “ ” ( ) are important for
maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and
performance of the set.
parts with specified ones for maintaining the safety and
performance of the set.
NOTES ON SCHEMATIC DIAGRAM
•
Resistor:
To differentiate the units of resistors, such symbol as K and
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
M are used: the symbol K means 1000 ohm and the symbol
M means 1000 kohm and the resistor without any symbol is
ohm-type resistor. Besides, the one with “Fusible” is a fuse
type.
•
Capacitor:
To indicate the unit of capacitor, a symbol P is used: this
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
symbol P means micro-micro-farad and the unit of the
capacitor without such a symbol is microfarad. As to
electrolytic capacitor, the expression “capacitance/withstand
voltage” is used.
(CH), (TH), (RH), (UJ): Temperature compensation
(ML): Mylar type
(P.P.): Polypropylene type
•
Schematic diagram and Wiring Side of P.W.Board for this
model are subject to change for improvement without prior
notice.
notice.
REF. NO
DESCRIPTION
POSITION
POSITION
REF. NO
DESCRIPTION
SW719
VOLUME DOWN
ON—OFF
SW720
VOLUME UP
ON—OFF
SW725
BASS/TREBLE
ON—OFF
SW726
MEMORY/SET
ON—OFF
SW727
CLEAR
ON—OFF
SW728
FUNCTION
ON—OFF
SW802
CD LID
ON—OFF
E C B
(S) (G) (D)
FRONT
VIEW
FRONT
VIEW
VIEW
B C E
FRONT
VIEW
2SB562 C
2SC380 O
2SC535 C
2SK2541
KRA102 M
KRA107 M
KRC102 M
KRC104 M
KRC107 M
KTA1266 GR
KTC3199 GR
KTC3200 GR
2SC380 O
2SC535 C
2SK2541
KRA102 M
KRA107 M
KRC102 M
KRC104 M
KRC107 M
KTA1266 GR
KTC3199 GR
KTC3200 GR
2SD2012 Y
LP99B
LP3052D
LP3052D
SVC348S
1 2 3
(1) (2) (3)
Figure 19 TYPES OF TRANSISTOR AND LED
XL-3500H
– 20 –
WAVEFORMS OF CD CIRCUIT
NO DISC FOCUS SEARCH
STOP PLAY
FOO
1
TMAX
1
IC801 33pin
FO+
2
SBOK
2
IC803 26pin
IC801 8pin
FO-
3
DMO
3
IC803 25pin
IC801 41pin
FOCUS SEARCH TOC IL
STOP PLAY
SEL
1
TEI
1
IC801 38pin
FEI
2
TRO
2
IC801 29pin
IC801 34pin
TEI
3
FMO
3
IC801 31pin
IC801 40pin
STOP PLAY
CUE
FEI
1
TEI
1
IC801 29pin
SBAD
2
TRO
2
IC801 30pin
IC801 34pin
RFO
3
FMO
3
IC802 22pin
IC801 40pin
STOP PLAY
REVIEW
FEI
1
TEI
1
IC801 29pin
RFGO
2
TRO
2
IC802 19pin
IC801 34pin
RFRP
3
FMO
3
IC802 17pin
IC801 40pin
STOP PLAY
TCD-782 TNO-02 PLAYBACK
TEI
1
LO
1
IC801 31pin
TRO
2
IC801 34pin
RO
2
SBAD
3
IC801 30pin
1
2
3
4
6
7
11
15
16
17
IC801 53pin
IC801 31pin
IC801 31pin
IC801 31pin
IC801 16pin
5
6
5
7
8
5
9
10
6
11
12
13
14
6
11
15
6
11
15
IC801 50pin
Click on the first or last page to see other XL-3500 (serv.man20) service manuals if exist.