Sharp HT-SB32D (serv.man2) User Manual / Operation Manual ▷ View online
5
TV Operation Buttons (Only SHARP TV):
On/Standby
On/Standby
Button
CH
VOL
Sets the TV power to
“ON” or “STANDBY”.
Input Select
Button (TV)
CH
VOL
Press the button to
switch the input source.
Volume Up
and Down
Buttons
CH
VOL
Turn up/down the TV
volume.
Channel Up and
Down Buttons
CH
VOL
Switch up/down the TV
channels.
Note: ● Some models of SHARP TV may not be operable.
●
SHARP TV remote control will not work with HT-SB32D system.
MUTE
ON/
STAND-BY
MUSIC
CINEMA
NEWS
SURROUND
BYPASS
INPUT
TV
CH
VOL
VOL
RRMCGA322AWSA
SOUND MODE
10
12
13
13
14
15
2
7
8
9
11
1
5
3
4
6
Remote control
Plastic shield
Battery holder
Note:
Before using remote control, please remove
plastic shield at battery holder.
1. Remote Control Transmitter
2. Mute Button
3. Cinema (Sound Mode) button
4. Music (Sound Mode) button
5. Surround Button
6. Bypass (Sound Mode) button
7. TV Operation Buttons (only SHARP TV)
8. Bluetooth Pairing Button
9. Bluetooth Play/Pause Button
10. Bluetooth Skip Up Button
11. Bluetooth Skip Down Button
12. On/Standby Button
13. News (Sound Mode) button
14. Input Button
15. Volume Up/Down Buttons
Controls and indicators (continued)
■
Remote Control
6
Make sure to unplug the AC power lead before in-
stalling the sound bar or changing the position.
Using spike legs
1
Peel the double sided tape separator.
2
Fix the spike leg onto the sound bar as
shown.
To mount the sound bar on the wall
Caution:
●
Be very careful to prevent the sound bar [2.3 kg
(5.1 lbs.)] from falling when mounting on the wall.
●
Before mounting, check the wall strength. (Do not
put on the veneer plaster or whitewashed wall. The
sound bar may fall.) If unsure, consult a qualified
service technician.
●
Mounting screws are not supplied. Use appropri-
ate ones.
●
Check all wall mount angle screws for looseness.
●
Select a good location. If not, accidents may occur
or the sound bar may get damaged.
●
SHARP is not responsible for accidents result-
ing from improper installation.
■
Driving screws
SHARP designed the sound bar so you may hang
it on the wall. Use proper screws (not supplied).
See below for size and type.
3.2 mm
9 mm
22 mm
5 mm
■
Installing the sound bar
1
Fix the pattern paper to the wall in hori-
zontal position as below.
44 mm
509 mm
Wall surface
Pattern paper
(supplied)
548 mm
2
Make a hole on the wall following the screw
point marks on the pattern paper by using
a drill.
Wall surface
32 mm
8-9 mm
3
Fix a wall mount plug into the hole using
a hammer, until it is flush with the wall
surface.
32 mm
8-9 mm
Wall sur
face
4
Fasten the screws to the wall as shown below.
(Total screw is 2 pieces)
Wall surface
Wall surface
Screw using
screwdriver
4.5 mm - 5 mm
Gap from wall
surface
5
Hang the sound bar onto the screws.
Bottom of
sound bar
Spike leg
Double sided
tape separator
System preparation
7
Installation image:
SOUND BAR HOME THEATRE SYSTEM HT-SB32D
Place the
sound
bar as
shown.
Notes:
●
Remove the protective film covering
the sound bar before turning on the
system.
●
The front panel of the sound bar is
not removable.
Caution:
●
Do not change the installation
direction when the sound bar is
turned on.
●
Do not stand or sit on the sound bar
as you may be injured.
TV
VCR
DVD player
●
Safety wires (not supplied) are useful to prevent the sound bar from falling.
Placing the sound bar
Falling prevention
8
Rack/
table
Screw eye
(not supplied)
Safety wires
(not supplied)
Screw eye
(not supplied)
Sound bar
SOUND BAR HOME THEATRE SYSTEM HT-SB32D
Safety wires
(not supplied)
Sound bar
Screw eye (not supplied)
Wall
Falling prevention (continued)
■
When mounting on the wall
■
When placing on the shelf/table
Click on the first or last page to see other HT-SB32D (serv.man2) service manuals if exist.