Sharp HT-SB250 User Manual / Operation Manual ▷ View online
9
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Pre
p
ar
at
ion
f
o
r
Use
System preparation
Select from three installation methods according to the preferred
position.
position.
Notes:
z
Option 1 or option 2 indicates spike positions based on LCD
TV stand.
z
When attaching the spikes, place the unit on a cushion or soft
cloth to avoid damage.
Caution:
When using these spikes on glossy or slippery table such as on
glass top, stick foot cushions at the bottom of the spikes to avoid
slippage.
Note:
Option 1 or option 2 foot cushion positions based on LCD TV
stand.
stand.
Make sure to unplug the AC power lead before installing
the unit or changing the position.
the unit or changing the position.
HT-SB250
Tighten all spikes as shown
Option 2
Option 1
Using spikes
Nuts (secured on spikes) must be used when installing spikes.
The unit can be levelled by adjusting the spikes and nuts.
Attach foot cushions as shown
Option 1
Option 2
Using foot cushions
10
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Prep
arat
ion fo
r
Us
e
System preparation (continued)
Caution:
z
Be very careful to prevent the unit [1.90 kg] from falling when
mounting on the wall.
mounting on the wall.
z
Before mounting, check the wall strength. (Do not put on the
veneer plaster or whitewashed wall. The unit may fall.) If
unsure, consult a qualified service technician.
veneer plaster or whitewashed wall. The unit may fall.) If
unsure, consult a qualified service technician.
z
Mounting screws are not supplied. Use appropriate ones.
z
Check all wall mount angle screws for looseness.
z
Select a good location. If not, accidents may occur or the unit
may get damaged.
may get damaged.
z
SHARP is not responsible for accidents resulting from
improper installation.
improper installation.
Driving screws
SHARP designed the units so you may hang them on the wall.
Use proper screws (not supplied). See below for size and type.
Wall mount angle fixed to the wall
(Horizontal position)
(Continued to the next page)
To mount the unit on the wall
3.2 mm
9 mm
Min. 22 mm
5 mm
1
Fix the pattern paper to the wall in horizontal position
as below.
2
Make a hole on the wall following the screw point
marks on the pattern paper by using a drill.
3
Fix a wall mount plug into the hole using a hammer,
until it is flush with the wall surface.
until it is flush with the wall surface.
29 mm
29 mm
44 mm
44 mm
509 mm
Pattern paper
Wall surface
Wall surface
8-9 mm
32 mm
Wall surface
8-9 mm
32 mm
11
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Pre
p
ar
at
ion
f
o
r
Use
Note:
Make sure all screws are fully tightened. (screws are not
supplied)
supplied)
Installing the sound bar
4
Screw the wall mount angle to the wall as shown in the
illustration. (Total screw is 8 pieces)
illustration. (Total screw is 8 pieces)
Wall surface
Wall mount angle
Wall mount angle
Wall surface
Wall surface
Wall mount angle
(screws x 4)
(screws x 4)
1
Align the wall mount slot at the unit to the wall mount
angle.
angle.
2
Slot the unit into the wall mount angle.
3
Fix them securely.
Wall surface
12
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Prep
arat
ion fo
r
Us
e
Placing the sound bar
Installation image:
Place the unit as shown.
Notes:
z
As the sound from the unit is omni-directional, you can place
it anywhere you like. However, it is recommended to place it
as close to the TV as possible.
it anywhere you like. However, it is recommended to place it
as close to the TV as possible.
z
The front panel of the unit is not removable.
Caution:
z
Do not change the installation direction when the unit is
turned on.
turned on.
z
Do not stand or sit on the unit as you may be injured.
Falling prevention
Safety wires (not supplied) are useful to prevent the unit from
falling off the table.
falling off the table.
Loop the safety wires (not supplied) into each hole as shown
and tie the safety wires to the LCD TV stand.
and tie the safety wires to the LCD TV stand.
TV
VCR
DVD player
Click on the first or last page to see other HT-SB250 service manuals if exist.