Sharp HT-SB250 User Manual / Operation Manual ▷ View online
13
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Prep
arat
ion fo
r
Us
e
Sound bar connections to TVs
Caution:
Turn off all other equipment before making any connections.
Tuner receiving for other audio system
z
Placing the aerial near the unit’s AC power lead may cause
noise pick up. Place the aerial away from the unit for better
reception.
noise pick up. Place the aerial away from the unit for better
reception.
Notes:
z
To connect to TV, use either LINE IN 1 sockets or AUDIO
LINE IN 2 socket only.
LINE IN 2 socket only.
z
Refer the operation manual of the equipment to be
connected.
connected.
z
Fully insert the plugs to avoid fuzzy pictures or noises.
Connecting to a TV
If the TV/monitor has an audio output, connect it to the LINE IN
1 sockets on the rear of the unit.
1 sockets on the rear of the unit.
To select LINE IN 1 function:
z
On the unit: Press FUNCTION button repeatedly until “L1” is
displayed.
displayed.
z
On remote control: Press LINE button repeatedly until “L1” is
displayed.
displayed.
RIGHT
LEFT
LINE IN 1
LINE IN 2
To audio output sockets
RCA cable (supplied)
Sound bar
TV
To LINE IN 1
sockets
sockets
14
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Prep
arat
ion fo
r
Us
e
Sound bar connections to TVs
(continued)
Connecting to a TV (with Headphone socket)
If the TV/monitor has headphone socket, connect it to the LINE
IN 2 socket on the rear of the unit.
IN 2 socket on the rear of the unit.
To select LINE IN 2 function:
z
On the unit: Press FUNCTION button repeatedly until “L2” is
displayed.
z
On remote control: Press LINE button repeatedly until “L2” is
displayed.
Notes:
z
If the TV volume is continuously in low level, the unit will
automatically power off. Increase the TV output volume to
enjoy the sound from the speaker.
z
If the unit volume is continuously in very high level, the unit
will mute and recover after 3 seconds.
AC power connection
After checking all the connections have been made correctly,
connect the AC power lead to the AC power input socket, then
to the wall socket.
connect the AC power lead to the AC power input socket, then
to the wall socket.
Using with the AC/DC adaptor
Notes:
z
Unplug the AC/DC adaptor from the wall socket if the unit will
not be used for a long period of time.
not be used for a long period of time.
z
Use only the supplied AC/DC adaptor. Using other AC/DC
adaptor may cause an electric shock or fire.
adaptor may cause an electric shock or fire.
RIGHT
LEFT
HEADPHONE
LINE IN 1
LINE IN 2
To HEADPHONE socket
Audio cable (not supplied)
Sound bar
TV
To AUDIO LINE
IN 2 socket
IN 2 socket
1
Plug the AC power lead into the AC/DC adaptor.
2
Plug the AC/DC adaptor cable into the DC IN socket on
the unit.
the unit.
3
Plug the AC power lead into a wall socket. The STAND-
BY indicator will turn RED when AC power is applied.
BY indicator will turn RED when AC power is applied.
RIGHT
LEFT
LINE IN 1
LINE IN 2
2
1
AC/DC Adaptor
Cable
DC IN socket
(DC 12 V)
AC/DC Adaptor
(AC 100 - 240 V ~ 50/60 Hz)
Wall socket
AC power lead
15
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Prep
arat
ion fo
r
Us
e
Remote control
Battery installation
Precautions for battery use:
z
Remove the battery if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
period of time. This will prevent potential damage due to
battery leakage.
Caution:
z
Do not use rechargeable battery (nickel-cadmium battery, etc.).
z
Danger of explosion if battery is incorrectly replaced.
z
Replace only with the same or equivalent type.
z
Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
z
Installing the battery incorrectly may cause the unit to
malfunction.
Notes concerning use:
z
Replace the battery if the operating distance is reduced or if
the operation becomes erratic. Purchase “CR 2025”, coin
lithium battery.
z
Periodically clean the transmitter on the remote control and
the sensor on the unit with a soft cloth.
z
Exposing the sensor on the unit to strong light may interfere
with operation. Change the lighting or the direction of the unit
if this occurs.
z
Keep the remote control away from moisture, heat, shock,
and vibrations.
Test of the remote control
Point the remote control directly at the remote sensor on the unit.
The remote control can be used within the range shown
below:
Press the ON/STAND-BY button. Does the power turn on? Now,
The remote control can be used within the range shown
below:
Press the ON/STAND-BY button. Does the power turn on? Now,
you can enjoy your system.
1
Insert pin into the hole as shown and pull to open the
battery holder.
battery holder.
2
Remove the old battery from the battery holder, insert
the new battery and then slide the battery holder back
into the remote control.
the new battery and then slide the battery holder back
into the remote control.
Back of
remote control
Pin
Battery holder
Polarity (+) symbol
Battery type
Locking tab
Positive (+) side up
SOUND BAR SYSTEM HT-SB250
SPORT
NEWS
CINEMA/GAME
15° 15°
Remote sensor
0.2 m - 6 m
(8” - 20’)
16
HT-SB250(BK)
2010 December 29
HT-SB250_A6_EN_UK.fm
HT-SB250(W)
Ba
sic Op
erat
ion
General control
To turn the power on
Press the ON/STAND-BY button.
z
The sound mode indicator and display light up. If the power
does not turn on, check whether the power lead is plugged in
properly.
To set the unit to stand-by mode:
z
Press the ON/STAND-BY button again.
The STAND-BY indicator turns red.
Display brightness control
Press the DIMMER button to adjust the brightness of the display
and sound mode indicator.
Volume auto fade-in
If you turn off and on the unit with the volume set to 40 or higher,
the volume starts at 20 and fades in to the last set level.
Volume control
Remote control operation:
Press the VOLUME + button to increase the volume and the
VOLUME – button to decrease the volume.
Preset sound mode
Main unit operation:
To change to a different mode, press the SURROUND button
To change to a different mode, press the SURROUND button
repeatedly until the desired sound mode lights up.
Remote control operation:
Remote control operation:
Press a desired sound mode on the remote control.
CINEMA/GAME
SPORT
Sound mode indicator and display bright
Sound mode indicator and display dim
Sound mode indicator and display off. Pressing
any button will light up the display for 3 seconds only.
Unit operation:
Press volume up (VOL. +) to increase
Press volume up (VOL. +) to increase
the volume and press volume down
(VOL. – ) to decrease the volume.
Muting
The volume is muted temporarily when pressing
the MUTE button on the remote control. Press
again to restore the volume.
00 01 02 ..... 59 60
WOW HD is on for nominal effect.
WOW HD on for cinema/game sound effect
WOW HD on for news
WOW HD on for sport broadcasting
STANDARD
CINEMA/GAME
NEWS
SPORT
Click on the first or last page to see other HT-SB250 service manuals if exist.