Sharp FV-DB1E (serv.man2) User Manual / Operation Manual ▷ View online
13
FV-DB1E
04/4/12
FV-DB1E_2.fm
TINSEA025SJZZ
FM Opera
tion
Listening to the FM
Notes:
"
When radio interference occurs, auto scan tuning may stop auto-
matically at that point.
matically at that point.
"
Auto scan tuning will skip weak signal stations.
"
To stop the auto tuning, press the TUNING button again.
To receive an FM stereo transmission:
Press the BAND button to display the "ST" indicator.
Press the BAND button to display the "ST" indicator.
"
" " will appear when an FM broadcast is in stereo.
"
If the FM reception is weak, press the BAND button to extinguish
the "ST" indicator. The reception changes to monaural, and the
sound becomes clearer.
the "ST" indicator. The reception changes to monaural, and the
sound becomes clearer.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the BAND button until "FM" ap-
pears on the display.
pears on the display.
3
Press the TUNING ( or ) button to tune in to the desired
station.
station.
Manual tuning:
Press the TUNING button as many times as required to tune in
to the desired station.
to the desired station.
Auto tuning:
When the TUNING button is pressed for 2 seconds or more,
scanning will start automatically and the tuner will stop at the
first receivable broadcast station.
scanning will start automatically and the tuner will stop at the
first receivable broadcast station.
FM stereo mode indicator
FM stereo receiving indicator
FM stereo receiving indicator
4
14
FV-DB1E
04/4/12
FV-DB1E_2.fm
TINSEA025SJZZ
A
d
v
a
n
ced Fea
tures
Storing stations
!
Memorising a station
You can store up to 20 DAB and FM stations (5 stations for each
zone A-D) and recall them at the press of a button.
For FM stations, stereo and mono modes are memorised.
zone A-D) and recall them at the press of a button.
For FM stations, stereo and mono modes are memorised.
Note:
If memory batteries are not inserted or low, preset stations will be
lost. When the AC adaptor is connected, preset stations remain
without memory batteries. Preset stations will be lost if the unit is
powered only by the main batteries and set to the power stand-by
mode.
If memory batteries are not inserted or low, preset stations will be
lost. When the AC adaptor is connected, preset stations remain
without memory batteries. Preset stations will be lost if the unit is
powered only by the main batteries and set to the power stand-by
mode.
!
To recall a memorised station
Note:
If the selected preset number is empty the display shows
"Preset ** empty".
If the selected preset number is empty the display shows
"Preset ** empty".
!
To erase entire preset memory
1
Tune in to the desired station (see page 9, 13).
2
Press the PRESET SELECT button repeatedly to select the
desired preset zone.
desired preset zone.
Zone A
Zone B
Zone C
Zone D
3
Hold down the PRESET button (1 - 5) for
2 seconds or more to store the station
in memory.
2 seconds or more to store the station
in memory.
4
Repeat steps 1 - 3 to set other stations, or to change a pre-
set station.
set station.
When a new station is stored in memory, the station previously
memorised will be erased.
memorised will be erased.
1
Press the PRESET SELECT button repeatedly to select the
desired preset zone.
desired preset zone.
2
Press the PRESET button (1 - 5) for less
than 1 second to recall a station.
than 1 second to recall a station.
1
Hold down the PRESET SELECT button
for 2 seconds or more.
for 2 seconds or more.
2
Within 30 seconds, press the ENTER
button.
button.
15
FV-DB1E
04/4/12
FV-DB1E_2.fm
TINSEA025SJZZ
A
d
v
a
n
ced Fea
tures
Alarm operation
At the set time, the alarm sounds or the radio turns on.
Once set, the alarm performs the operation every day.
Once set, the alarm performs the operation every day.
Use when...
You want to use the alarm as a wake up call, or listen to the radio at
the same time every day.
You want to use the alarm as a wake up call, or listen to the radio at
the same time every day.
Before setting alarm:
1
When setting the alarm, connect the AC adaptor to the unit.
If batteries are the only power source, you cannot set the
alarm (see page 6).
If batteries are the only power source, you cannot set the
alarm (see page 6).
2
If the clock is not set, the alarm setting is not available ("No
time date" appears). Receive a DAB station to set date and
time (see page 8, 9).
time date" appears). Receive a DAB station to set date and
time (see page 8, 9).
1
Press the ON/STAND-BY button to turn the power on.
2
To use "Radio" as an alarm, tune in to a station and adjust
the volume.
To use "Tone" as an alarm, proceed to step 3.
the volume.
To use "Tone" as an alarm, proceed to step 3.
3
Press the CLOCK button repeatedly to
select "Set alarm ok?", then press the
ENTER button.
select "Set alarm ok?", then press the
ENTER button.
4
Within 30 seconds, press the TUNING
( or ) button to specify the hour to
start, then press the ENTER button.
( or ) button to specify the hour to
start, then press the ENTER button.
5
Within 30 seconds, press the TUNING
( or ) button to specify the minutes
to start, then press the ENTER button.
( or ) button to specify the minutes
to start, then press the ENTER button.
6
Within 30 seconds, press the TUNING
( or ) button to select the desired
alarm type.
( or ) button to select the desired
alarm type.
Tone:
The alarm sounds at the set time, and stops after 5
minutes. The volume gradually increases from 0 and
reaches 40 after 1 minute.
minutes. The volume gradually increases from 0 and
reaches 40 after 1 minute.
Radio:
The radio turns on at the set time, and turns off after
1 hour. The volume gradually increases from 0 and
reaches the level set in step 2 after 1 minute.
1 hour. The volume gradually increases from 0 and
reaches the level set in step 2 after 1 minute.
7
Within 30 seconds, press the ENTER
button.
" " will light up.
button.
" " will light up.
8
At the set time, the alarm operation will start.
"
The current date/time and the remaining time appear alternately.
"
The volume decreases 1 minute before the alarm operation
finishes.
finishes.
5
16
FV-DB1E
04/4/12
FV-DB1E_2.fm
TINSEA025SJZZ
A
d
v
a
n
ced Fea
tures
Alarm operation (continued)
To cancel the alarm setting:
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the alarm operation without setting the unit to the stand-by
mode, press the CLOCK button until "Alarm off ok?" appears on the
display, then press the ENTER button.
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the alarm operation without setting the unit to the stand-by
mode, press the CLOCK button until "Alarm off ok?" appears on the
display, then press the ENTER button.
To reset or change the alarm setting:
Perform "Alarm operation" from the beginning (see page 15).
Perform "Alarm operation" from the beginning (see page 15).
Notes:
"
The alarm operates at the same time every day until the setting is
cancelled. Cancel the alarm when it is not in use.
cancelled. Cancel the alarm when it is not in use.
"
If the unit is unplugged or a power failure occurs in the alarm
stand-by mode, the " " indicator turns off and the alarm setting is
cancelled.
stand-by mode, the " " indicator turns off and the alarm setting is
cancelled.
"
During the sleep operation, the alarm setting is not available.
Sleep operation
When the set time elapses, sound is muted with the power on.
Before setting sleep:
Before setting sleep:
Stopping the alarm:
Press the ON/STAND-BY button.
About snooze function:
You can pause the alarm sound by press-
ing buttons other than the ON/STAND-BY
button. In this case, the alarm resumes af-
ter 7 minutes.
ing buttons other than the ON/STAND-BY
button. In this case, the alarm resumes af-
ter 7 minutes.
The remaining time also appears.
Tone:
The alarm stops after 5 minutes when the snooze is not used. If
you use the snooze repeatedly, the alarm will be disabled after 1
hour.
you use the snooze repeatedly, the alarm will be disabled after 1
hour.
Radio:
The alarm will be disabled after 1 hour.
For the sleep operation, connect the AC adaptor to the unit.
If batteries are the only power source, setting is not possible
(see page 6).
If batteries are the only power source, setting is not possible
(see page 6).
1
Press the CLOCK button repeatedly to
select "Set sleep".
select "Set sleep".
2
Within 30 seconds, press the TUNING
( or ) button to select the desired
sleep time.
( or ) button to select the desired
sleep time.
"
Select set time from 1 - 120 minutes by
the minute.
the minute.
"
Press the TUNING ( or ) button once to advance the time
by 1 minute. Hold it down to advance continuously.
by 1 minute. Hold it down to advance continuously.
3
Within 30 seconds, press the ENTER
button.
button.
"
" " will light up.
"
Remaining time is displayed during the sleep operation.
"
The volume gradually decreases for the last 1 minute.
4
Sound will be muted after the set time
elapses.
elapses.
" " turns off.
To stop the sleep operation:
Press any button on the unit
whilst "Sleeping" is displayed.
Press any button on the unit
whilst "Sleeping" is displayed.
Sleep operation stops.
To cancel the sleep setting:
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, press the CLOCK button until "Sleep off ok?" appears on the
display, then press the ENTER button.
Press the ON/STAND-BY button whilst " " is indicated.
To cancel the sleep operation without setting the unit to the stand-by
mode, press the CLOCK button until "Sleep off ok?" appears on the
display, then press the ENTER button.
2
1
119
120
...
Click on the first or last page to see other FV-DB1E (serv.man2) service manuals if exist.