DOWNLOAD Sharp DK-KP80PH Service Manual ↓ Size: 2.49 MB | Pages: 32 in PDF or view online for FREE

● Sound will only switch from iPhone to the main unit

after authentication process is completed in
approximately 10 seconds. 

● Incoming calls will pause the playback.

● Once the calls are answered, the conversation can only

be heard through the built-in iPhone speaker. Turn on
the iPhone speaker or undock the iPhone to start
conversation.

Caution:
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.

Note:
Docking station is not recommended for iPad connection.

For iPod nano or iPod touch :
For additional support, apply dock spacer (supplied) as
shown.

Note:
When navigating the iPod, iPhone or iPad menu with remote
control, do not operate any of the buttons on the iPod or iPhone
unit. The volume level is adjusted by pressing the VOL (+ or –)
button on the main unit or the remote control. Adjusting the
volume on the iPod, iPhone or iPad units give no effect.

iPod, iPhone and iPad operations:
The operations described below depend on the generation iPod,
iPhone and iPad you are using.

System on operation:
When the main unit is powered on, the iPod, iPhone or iPad units
will automatically power on when docked or connected in the unit.

System off (stand-by operation):
When the main unit is turned to stand-by mode, the docked iPod,
iPhone or connected iPad unit will automatically turn to stand-by
mode.

■ iPhone playback

■ iPod and iPhone connection (Dock only)

Open the docking station for iPod and iPhone by pulling
up the cover.

Dock your iPod or iPhone into the unit.

Peel off the double sided tape separator.

Place the spacer between the two ribs of the iPod docking
cover as shown.

iPhone

Dock connector

iPhone (bottom)

 Dock for iPhone

Rib

iPod 
docking 
cover

Dock spacer

Peel off
separator

■ iPod or iPhone playback

Press the ON/STAND-BY button to turn the power on.

Press the iPod button on the remote control or FUNCTION
button repeatedly on the main unit to select iPod function.

Insert iPod or iPhone unit into the dock of main unit.  “DOCK
OK” will appear.

Press the  /  (iPod  / ) button to start playback.

■ Navigating the iPod,  iPhone or iPad 

Press the MENU button to view the menu on iPod, iPhone or
iPad unit. Press it again to go back to previous menu.

Use the PRESET (

 or 

) button to select an item on the

menu and then press ENTER button.

Simply remove the iPod or iPhone from the docking station
or iPad connector from USB terminal. It is safe to do so
even during playback.

● Unplug all accessories for the iPod or iPhone before

inserting it into the docking station.

● Stop button ( ) at main unit is invalid during iPod

function.

This system can play back a standard CD, CD-R/RW in the CD
format and CD-R/RW with MP3 or WMA files, but cannot record
on them. Some audio CD-R and CD-RW discs may not be
playable due to the state of the disc or the device that was used
for recording.

● This system supports MPEG 1 Layer 3 and VBR files.

● During VBR file playback, time counter in the display may

differ from its actual playback time.

● Bitrate which is supported by MP3 is 32 ~ 320 kbps.

● “MP3” and “WMA” indicator will light up after the unit reads

information on an MP3 or WMA disc.

● Bitrate which is supported by WMA is 64 ~ 160 kbps.

■ To disconnect iPod, iPhone or iPad

■ Various iPod, iPhone and iPad functions

Press in the pause 
mode.

Press in the 
playback mode.

Press in the 
playback or pause 
mode. 
If you press the 
button in the pause 
mode, press the  /

 button to start the 

desired track.

Press and hold 
down in the 
playback mode.

Release the button 
to resume 
playback.

____ 

Press to toggle 
repeat mode.

Press and hold 
to toggle shuffle 
mode.

____ 

Press to view the 
iPod menu during 
iPod function.

____ 

Press to confirm 
the selection.

____ 

Press to select the 
iPod menu.

■ Disc playback

Press the ON/STAND-BY button to turn the power on.

Press the CD button on the remote control or FUNCTION
button repeatedly on the main unit to select CD function.

Press the OPEN/CLOSE button to open the disc compartment.

Place the disc in the disc compartment, label side front.

● Do not place two discs in the disc compartment.

● Do not play discs of special shapes (heart, octagon, etc). It

may cause malfunctions.

● Do not push the disc compartment whilst it is moving.

● If the power fails whilst the compartment is open, wait until the

power is restored.

● If TV or radio interference occurs during CD operation, move

the unit away from the TV or radio.

● Be sure to place 8 cm (3") disc in the middle of the disc

compartment.

● Due to the structure of the disc information, it takes longer to

read an MP3/WMA disc than a normal CD (approximately 20
to 90 seconds).

● When the end of the last track is reached during fast forward,

“END” will appear on the display and CD operation will be
paused. When the beginning of the first track is reached
during fast reverse, the unit will enter the playback mode (only
for CD).

● Rewritable multi-session discs with unfinished writing, can

still be played.

By using the Numeric buttons, the desired tracks on the
current disc can be played.
Use the Numeric buttons on the remote control to select
the desired track whilst playing the selected disc.

● The Numeric buttons allow you to select up to number 9.

● When selecting number 10 or higher, use the “10+” button.

● A track number higher than the number of tracks on the

disc cannot be selected.

● During random play, direct search is not possible.
To stop playback:
Press 

the  

(CD ) 

button.

Repeat play can play one track, all tracks or a programmed
sequence continuously.
To repeat one track:
Press the PLAY MODE button repeatedly until “Repeat One”
appears. Press the  /  (CD  / ) button.
To repeat all tracks:
Press the PLAY MODE button repeatedly until “Repeat All”
appears. Press the  /  (CD  / ) button.
To repeat desired tracks:
Perform steps 1 - 5 in “Programmed play” section on page 11
and then press the PLAY MODE button repeatedly until
“Repeat All” appears.
To cancel repeat play:
Press the PLAY MODE button repeatedly until “Normal”
appears and “

” disappears.

Caution:
After performing repeat play, be sure to press the   (CD  ) 
button. Otherwise, the disc will play continuously.

Press the OPEN/CLOSE button to close the disc compartment.

Press the  /  (CD  /  ) button to start playback. After the 
last track is played, the unit will stop automatically.

■ Various disc functions

Press in the stop mode.

Press in the playback
mode. Press the  /   
button to resume 
playback from the 
paused point.

Press in the playback 
mode.

Press in the playback or 
stop mode. 
If you press the button in 
the stop mode, press the 

/  button to start the 

desired track.

Press and hold down in 
the playback mode.
Release the button to 
resume playback.

■ Direct track search

Press the “10+” button once.

Press the “1” button.

Press the “3” button.

Press the “10+” button twice.

Press the “1” button.

Press the “3” button.

Press the “0” button.

■ Repeat play

Selected track number

The tracks on the disc can be played in random order
automatically.

To random play all tracks:
Press and hold the PLAY MODE button on the remote control
until “Random” appears. Press the   /  (CD  / ) button.

To cancel random play:
Press the PLAY MODE button again. “RDM” indicator will
disappear.

● If you press the 

 button during random play, you can

move to the track selected next by the random operation.
On the other hand, the  

 button does not allow you to

move to the previous track. The beginning of the track
being played will be located.

● In random play, the unit will select and play tracks

automatically. (You cannot select the order of the tracks.)

You can choose up to 32 selections for playback in the order
you like.

To cancel the programmed play mode:
During programmed stop mode, press the   (CD  )
button. The display will show “Memory Clear” and all the
programmed contents will be cleared.

Adding tracks to the programme:
If a programme has been previously stored, the “MEM”
indicator will be displayed. Press the MEMORY button.
Then follow steps 2 - 3 to add tracks.

● When the disc compartment is opened, the programme

is automatically cancelled.

● If you press the ON/STAND-BY button to enter the

stand-by mode or change the function from CD to
another, the programmed selections will be cleared.

● During the programme operation, random play is not

possible.

■ Random play

■ Programmed play (CD)

Whilst in the stop mode, press the MEMORY button on the
remote control to enter the programming save mode.

Press the numeric button or 

 or 

 buttons on the

remote control to select the desired track.

Press the MEMORY button to save the track number.

Repeat steps 2 - 3 for other tracks. Up to 32 tracks can be
programmed. If you want to check the programmed tracks,
press the MEMORY button repeatedly. If you make a
mistake, the programmed tracks can be cleared by
pressing the CLEAR button.

Press the   /  (CD  / ) button to start playback.  

Selected track number

■ Programmed play (MP3/WMA)

Whilst in the stop mode, press the MEMORY button to
enter the programming save mode.

Press the PRESET (

 

or 

) button on the remote

control to select the desired folder.

Then press the 

 or 

  button on the remote control

to select the desired tracks.

Press the MEMORY button to save the folder and track
number.

Repeat steps 2 – 3 for other folder/tracks. Up to 32
tracks can be programmed.

Press the   /  (CD  / ) button to start playback.