Sharp DK-KP80PH User Manual / Operation Manual ▷ View online
E-4
System connections
Supplied FM aerial:
Connect the FM aerial wire to the FM 75 OHMS socket and
position the FM aerial wire in the direction where the
strongest signal can be received.
Connect the FM aerial wire to the FM 75 OHMS socket and
position the FM aerial wire in the direction where the
strongest signal can be received.
External FM aerial:
Use an external FM aerial (75 ohms coaxial cable) for
better reception. When an external FM aerial is used,
disconnect the supplied FM aerial wire.
Use an external FM aerial (75 ohms coaxial cable) for
better reception. When an external FM aerial is used,
disconnect the supplied FM aerial wire.
Note:
Placing the aerial on the unit or near the AC power lead
may cause noise pickup. Place the aerial away from the
unit for better reception.
Placing the aerial on the unit or near the AC power lead
may cause noise pickup. Place the aerial away from the
unit for better reception.
After checking all the connections have been made
correctly, plug the AC power lead of this unit into the wall
socket.
correctly, plug the AC power lead of this unit into the wall
socket.
Note:
Unplug the AC power lead from the wall socket if the unit
will not be in use for a prolonged period of time.
Unplug the AC power lead from the wall socket if the unit
will not be in use for a prolonged period of time.
● The first time the unit is plugged in, the unit will enter
the demonstration mode.
● To cancel the demonstration mode, press the DEMO
button (remote control) during power stand-by mode.
The unit will enter the low power consumption mode.
The unit will enter the low power consumption mode.
● To return to the demonstration mode, press the DEMO
button again.
● If iPod or iPhone is docked, the unit will begin charging.
“Charge Mode” will displayed. Demonstration mode is
invalid during charge mode.
invalid during charge mode.
Make sure to unplug the AC power lead before making any connections.
Wall socket
(AC 220 - 240 V ~ 50/60 Hz)
External FM
antenna for better
reception (not
supplied)
FM aerial
AM loop antenna
■ Aerial connection
■ AC power connection
■ Demonstration mode
E-5
Remote control
Caution:
● Remove the battery if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
battery leakage.
● Do not use rechargeable battery (nickel-cadmium battery,
etc.).
● Installing the battery incorrectly may cause the unit to
malfunction.
● Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the
like.
like.
Notes concerning use:
● Replace the battery if the operating distance is reduced or
if the operation becomes erratic. Purchase a “AA” size
battery (UM/SUM-3, R6, HP-7 or similar).
battery (UM/SUM-3, R6, HP-7 or similar).
● Periodically clean the transmitter on the remote control
and the sensor on the unit with a soft cloth.
● Exposing the sensor on the unit to strong light may
interfere with operation. Change the lighting or the
direction of the unit if this occurs.
direction of the unit if this occurs.
● Keep the remote control away from moisture, heat, shock,
and vibrations.
Check the remote control after checking all the connections.
Point the remote control directly at the remote sensor on the
unit. The remote control can be used within the range shown
below:
Point the remote control directly at the remote sensor on the
unit. The remote control can be used within the range shown
below:
General control
Press the ON/STAND-BY button to turn the power on.
To dim the display brightness, press the DIMMER button on
the remote control.
the remote control.
If you turn off and on the main unit with the volume set to 27
or higher, the volume starts at 16 and fades in to the last set
level.
or higher, the volume starts at 16 and fades in to the last set
level.
Press VOL +/- to increase or decrease the volume.
When you press any of the following buttons, the unit turns on.
● iPod, CD/USB, AUDIO IN, TUNER on the remote control:
Selected function is activated.
●
/ button on the main unit: The unit turns on and
playback of the last function will start (CD, TUNER, USB,
iPod, AUDIO IN)
iPod, AUDIO IN)
■ Battery installation
1
Open the battery cover.
2
Insert the supplied battery according to the terminal
indicated in the battery compartment.
indicated in the battery compartment.
When inserting or removing the battery, push it towards the
(–) battery terminals.
(–) battery terminals.
3
Close the cover.
■ Test of the remote control
0.2 m - 6 m
(8" - 20' )
Remote sensor
■ To turn the power on
After use:
Press the ON/STAND-BY button to enter the power stand-
by mode.
Press the ON/STAND-BY button to enter the power stand-
by mode.
■ Display brightness control
■ Volume auto fade-in
■ Volume control
■ Direct key power on function
Dimmer 1
Dimmer 2
Dimmer off
(Display is dim).
(Display is bright).
(Display gets dimmer).
E-6
General control (continued)
The main unit will enter the stand-by mode (when iPad, iPod
or iPhone is not connected) after 15 minutes of inactivity
during:
iPod :
or iPhone is not connected) after 15 minutes of inactivity
during:
iPod :
Not docked.
Audio In : No detection of input signal.
CD :
CD :
In the stop mode or no disc.
USB :
In the stop mode or no media.
Note:
However, if iPod or iPhone is docked, the unit will begin
charging.
“Charge Mode” will be displayed.
However, if iPod or iPhone is docked, the unit will begin
charging.
“Charge Mode” will be displayed.
The volume is muted temporarily when pressing the MUTE
button on the remote control. Press again to restore the
volume.
button on the remote control. Press again to restore the
volume.
When the power is first turned on, the unit will enter the extra
bass mode which emphasises the bass frequencies, and
“X-BASS” indicator will appear. To cancel the extra bass
mode, press the X-BASS button on the remote control.
bass mode which emphasises the bass frequencies, and
“X-BASS” indicator will appear. To cancel the extra bass
mode, press the X-BASS button on the remote control.
1
Press the BASS/TREBLE button to select “Bass”.
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the bass. “X-BASS” indicator will disappear.
adjust the bass. “X-BASS” indicator will disappear.
1
Press the BASS/TREBLE button to select “Treble”.
2
Within 5 seconds, press the VOLUME (+ or –) button to
adjust the treble. “X-BASS” indicator will disappear.
adjust the treble. “X-BASS” indicator will disappear.
When the FUNCTION button on main unit is pressed, the
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
current function will change to different mode. Press the
FUNCTION button repeatedly to select desired function.
Note:
The backup function will protect the memorised function
mode for a few hours should there be a power failure or the
AC power lead becomes disconnected.
The backup function will protect the memorised function
mode for a few hours should there be a power failure or the
AC power lead becomes disconnected.
Setting the clock (Remote control only)
In this example, the clock is set for the 24-hour (0:00) display.
To confirm the time display:
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Press the CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note:
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
When power supply is restored after unit is plugged in again
or after a power failure, reset the clock.
To readjust the clock:
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
Perform “Setting the clock” from step 1. If the “Clock” does not
appear in step 2, step 4 (for selecting the 24-hour or 12-hour
display) will be skipped.
To change the 24-hour or 12-hour display:
■ Auto power off function
■ Muting
■ X-Bass control
■ Bass control
■ Treble control
■ Function
- 5
↔ - 4........↔ + 4 ↔ + 5
- 5
↔ - 4........↔ + 4 ↔ + 5
FM STEREO
FM MONO
USB
iPod
Audio In
AM
CD
1
Press the ON/STAND-BY button to turn the power on.
2
Press the CLOCK/TIMER button.
3
Within 10 seconds, press the ENTER button. To adjust
the day, press the
the day, press the
or
button and then press the
ENTER button.
4
Press the
or
button to select 24-hour or 12-hour
display and then press the ENTER button.
The 24-hour display will appear.
(0:00 - 23:59)
(0:00 - 23:59)
The 12-hour display will appear.
(AM 12:00 - PM 11:59)
(AM 12:00 - PM 11:59)
The 12-hour display will appear.
(AM 0:00 - PM 11:59)
(AM 0:00 - PM 11:59)
5
To adjust the hour, press the
or
button and then
press the ENTER button. Press the
or
button
once to advance the time by 1 hour. Hold it down to
advance continuously.
advance continuously.
6
To adjust the minutes, press the
or
button and
then press the ENTER button. Press the
or
button once to advance the time by 1 minute. Hold it
down to advance the time by 5 minutes interval.
down to advance the time by 5 minutes interval.
1
Clear all the programmed contents. [Refer to “Factory
reset, clearing all memory” on page 21 for details.]
reset, clearing all memory” on page 21 for details.]
2
Perform “Setting the clock” from step 1 onwards.
E-7
Listening to the iPod, iPhone or iPad
Made for:
● iPod touch (4
th
generation)
● iPod touch (3
rd
generation)
● iPod touch (2
nd
generation)
● iPod touch (1
st
generation)
● iPod classic
● iPod nano (6
th
generation)
● iPod nano (5
th
generation)
● iPod nano (4
th
generation)
● iPod nano (3
rd
generation)
● iPod nano (2
nd
generation)
● iPhone 4
● iPhone 3GS
● iPhone 3G
● iPhone
● iPad 2
● iPad
Caution:
Please update your iPod, iPhone and iPad unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod,
iPhone and iPad.
Notes:
Caution:
Please update your iPod, iPhone and iPad unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod,
iPhone and iPad.
Notes:
● Charging terminal for iPod, iPhone and iPad:
● The message “This accessory is not made to work with
iPhone” or similar, mat appear on the iPhone screen
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
when:
- battery is low.
- the iPhone is not properly docked (eg. slanting).
If this occurs, remove and re-dock the iPhone.
● This product is made for iPod, iPhone and iPad. To
prevent random interference when iPod, iPhone or
iPad is connected, the headphone output is disabled,
and “HP INVALID” will be displayed.
You may also experience brief audio interference
during incoming calls.
iPad is connected, the headphone output is disabled,
and “HP INVALID” will be displayed.
You may also experience brief audio interference
during incoming calls.
● The headphone output is switched off during inserting
iPod, iPhone and iPad unit. This is an Apple product
specification.
specification.
1
Press the ON/STAND-BY button to turn the power on.
2
Press the USB button on the remote control or
FUNCTION button repeatedly on the main unit to select
USB function.
FUNCTION button repeatedly on the main unit to select
USB function.
3
Connect iPod, iPhone or iPad to the unit. “USB/iPod” will
appear.
appear.
4
Press the / (USB / ) button to start playback.
Note:
Stop button ( ) is invalid during iPod, iPhone or iPad
playback
Stop button ( ) is invalid during iPod, iPhone or iPad
playback
Condition
DOCK
USB
USB function
NO
YES
Other function
YES
NO
Stand-by
YES
NO
■ iPod, iPhone and iPad connection (USB
only)
1
Insert the connector to the iPod, iPhone or iPad.
2
Place the iPad to the stand for iPad.
3
Connect the iPod, iPhone or iPad to the unit via USB
connector.
connector.
■ iPod, iPhone or iPad playback via USB
terminal
iPad
Connector
iPad
Stand for iPad
USB
File name
Click on the first or last page to see other DK-KP80PH service manuals if exist.