Sharp DK-A1H (serv.man2) User Manual / Operation Manual ▷ View online
13
DK-A1H
DK-A1H(BK)
Basic Operation
Setting the clock
In this example, the clock is set for the 12-hour (12:00 AM) display.
To confirm the time display:
[When the unit is in the stand-by mode or in demonstration mode.]
Press the CLOCK button to enter the clock function.
[When the unit is in the stand-by mode or in demonstration mode.]
Press the CLOCK button to enter the clock function.
[When the power is on]
Press DISPLAY button on the remote control to toggle between the
function information and clock display.
Notes:
Press DISPLAY button on the remote control to toggle between the
function information and clock display.
Notes:
The clock will continue counting for 8 hours should there be a
power failure or the AC power lead becomes disconnected.
The “CLOCK ADJ” will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit after 8 hours. If incorrect, readjust the clock
as follows.
power failure or the AC power lead becomes disconnected.
The “CLOCK ADJ” will appear or time will flash to confirm the time
display when the AC power supply is restored after a power failure
or unplugging the unit after 8 hours. If incorrect, readjust the clock
as follows.
To readjust the clock:
Perform “Setting the clock” from step 1 to step 4.
Perform “Setting the clock” from step 1 to step 4.
To change the 12-hour or 24-hour display:
Summer Time:
The Summer Time switch is located on the rear of the unit.
The Summer Time switch is located on the rear of the unit.
1
Press the CLOCK button for more than 2 seconds.
2
Press the
or
button to select 12-hour or 24-hour
display and then press the CLOCK button.
The 12-hour display will appear.
(12:00 AM - 11:59 PM)
The 12-hour display will appear.
(0:00 AM - 11:59 PM)
The 24-hour display will appear.
(0:00 - 23:59)
3
Press the
or
button to adjust the hour and then
press the CLOCK button.
Press the
or
button once to advance the time by 1 hour.
Hold it down to advance continuously.
CLOCK
SNOOZE
DIMMER
AUX
TUNER
iPod
ALARM
ALARM
ON/OFF
ON/OFF
4
Press the
or
button to adjust the minutes and then
press the CLOCK button.
Press the
or
button once to advance the time by
1 minute. Hold it down to change the time in 5-minutes interval.
1
Clear all the programmed contents. [Refer to “Clearing all the
memory (reset)” on page 28 for details.]
memory (reset)” on page 28 for details.]
2
Perform “Setting the clock” from step 1.
1
Slide the Summer Time switch to +1 to advance the
time 1 hour.
time 1 hour.
indicator will appear.
2
Slide the Summer Time switch to -1 to turn the clock
back 1 hour.
back 1 hour.
“12:00 AM”
“0:00 AM”
“0:00”
14
DK-A1H
DK-A1H(BK)
iPod
Listening to the iPod
Supported iPod models:
iPod nano (software 1.0 above)
iPod photo (software 1.0 above)
iPod mini (software 1.2 above)
5th Generation iPod (software 1.0 above) (Dock connector
equipped Click Wheel model)
4th Generation iPod (software 3.0.2 above) (Dock connector
equipped Click Wheel model)
3rd Generation iPod (software 2.2 above) (Dock connector
equipped Click Wheel model)
iPod photo (software 1.0 above)
iPod mini (software 1.2 above)
5th Generation iPod (software 1.0 above) (Dock connector
equipped Click Wheel model)
4th Generation iPod (software 3.0.2 above) (Dock connector
equipped Click Wheel model)
3rd Generation iPod (software 2.2 above) (Dock connector
equipped Click Wheel model)
Caution:
Please update your iPod unit to the latest software version before
using it. Please visit Apple’s homepage to download the latest
version for your iPod.
using it. Please visit Apple’s homepage to download the latest
version for your iPod.
Notes:
Once the iPod is connected to the unit it will begin charging.
The iPod unit can not be charged whilst the main unit is in the
stand-by mode.
The iPod unit can not be charged whilst the main unit is in the
stand-by mode.
Auto power on function:
When you press any of the following buttons, the unit turns on.
When you press any of the following buttons, the unit turns on.
iPod button (main unit): The unit turns on and the iPod function is
activated.
activated.
/ button (main unit and remote control): The unit turns on and
playback of the last function will start (iPod, TUNER, AUX).
iPod adaptor connection
Choose the iPod adaptor that fits your iPod. Your iPod will fit snuggly
into the correct adaptor. If your iPod is not mentioned below, an iPod
adaptor may have been included with your iPod unit.
into the correct adaptor. If your iPod is not mentioned below, an iPod
adaptor may have been included with your iPod unit.
Notes:
iPod nano (Second Generation) is not compatible with the original
iPod nano dock adaptor.
If you have an iPod that does not have an iPod connector, you can
use an audio cable to connect it to the AUX IN sockets.
iPod nano dock adaptor.
If you have an iPod that does not have an iPod connector, you can
use an audio cable to connect it to the AUX IN sockets.
iPod
Adaptor
No.
iPod Description
Capacity
3
iPod mini
4GB & 6GB
4
4G iPod & U2 iPod
20GB
5
4G iPod
40GB
6
iPod photo & Colour U2 iPod
20GB & 30GB
7
iPod photo
40GB & 60GB
6
iPod with colour display
20GB
7
iPod with colour display
60GB
8
iPod nano
2GB & 4GB
9
iPod (10/12/05 w/video)
30GB
10
iPod (10/12/05 w/video)
60GB
7
The number (3-10)
shows which iPod fits
shows which iPod fits
15
DK-A1H
DK-A1H(BK)
iPod
To insert iPod adaptor
1. Push the iPod sliding door until end.
2. Insert the iPod adaptor into unit and connect your iPod.
To remove iPod adaptor
iPod playback
To disconnect iPod
Simply remove the iPod from the iPod dock. It is safe to do so even
during playback.
Simply remove the iPod from the iPod dock. It is safe to do so even
during playback.
EQ
-
+
iPod
AUX
E SO
UN
E SO
UN
EQ
-
+
iPod
AUX
Dock connector
iPod (bottom)
iPod
iPod adaptor
iPod connector
iPod dock
E SO
UND
1
Press the ON/STAND-BY button to turn the power on.
2
Press the iPod button on main unit once or FUNCTION
button on remote control repeatedly to select iPod
function.
button on remote control repeatedly to select iPod
function.
3
Open the iPod terminal door and insert iPod unit in iPod
dock of main unit.
dock of main unit.
4
Press the / button to start playback.
Hold this tip and pull as direction shown
to remove adaptor.
to remove adaptor.
EQ
-
+
iPod
AUX
iPod adaptor
iPod
E SO
UN
16
DK-A1H
DK-A1H(BK)
iPod
Listening to the iPod (continued)
Various iPod functions
iPod operation
The operations described below depend on the generation iPod you
are using.
The operations described below depend on the generation iPod you
are using.
System on operation
When the main unit is powered on, the iPod unit will automatically
power on when docked in the unit (including alarm function).
* Invalid for 3rd iPod Generation.
When the main unit is powered on, the iPod unit will automatically
power on when docked in the unit (including alarm function).
* Invalid for 3rd iPod Generation.
System off (stand-by operation)
When the main unit is turned to stand-by mode, the docked iPod unit
will automatically turn to stand-by mode.
When the main unit is turned to stand-by mode, the docked iPod unit
will automatically turn to stand-by mode.
iPod playback detection function
Once play button on iPod unit is pressed, the unit will automatically
change to iPod function overriding the previous function selected.
Once play button on iPod unit is pressed, the unit will automatically
change to iPod function overriding the previous function selected.
Caution:
Unplug all accessories for the iPod before inserting it into the iPod
dock.
dock.
Function
Main unit
Remote
control
Operation
Play
Press in the pause
mode.
mode.
Pause
Press in the playback
mode.
mode.
Track up/
down
down
Press in the playback
or pause mode.
If you press the button
in the pause mode,
press the / button
to start the desired
track.
or pause mode.
If you press the button
in the pause mode,
press the / button
to start the desired
track.
Fast
forward/
reverse
forward/
reverse
Press and hold down
in the playback mode.
Release the button to
resume playback.
in the playback mode.
Release the button to
resume playback.
Display
____
iPod back light ON.
Repeat
____
Press to toggle repeat
mode.
mode.
Shuffle
____
Press and hold down
to toggle shuffle mode.
to toggle shuffle mode.
DISPLAY
PLAY
MODE
PLAY
MODE
Click on the first or last page to see other DK-A1H (serv.man2) service manuals if exist.