Sharp CD-SW200E (serv.man3) Service Manual ▷ View online
CD-SW200E
3 – 3
1
Woofer
(A1) x1
2. Screw
(A2) x4
......................
1. Front Panel .............
2
Tweeter
1. Screw ...................... (B1) x2
3
Super Tweeter
1. Screw ...................... (C1) x2
STEP
REMOVAL
PROCEDURE
CP-S200H
1
LED PWB
(A1) x1
3. Screw
(A3) x2
......................
2. Socket
(A2) x1
....................
1. Front Panel .............
2
Woofer
1. Screw ...................... (B1) x8
STEP
REMOVAL
PROCEDURE
CP-SW200E
Screwdriver
Speaker Box
(A1)x1
Driver should
be pried away
from Speaker Box.
be pried away
from Speaker Box.
Speaker Box
Woofer
Tweeter
Super Tweeter
(A2)x4
M4x16mm
M4x16mm
(C1)x2
M3x10mm
M3x10mm
(B1)x2
M3x10mm
M3x10mm
Screwdriver
Speaker Box
(A1)x1
Driver should
be pried away
from Speaker Box.
be pried away
from Speaker Box.
Front Panel
(A3)x2
M2.6x10mm
M2.6x10mm
LED PWB
(A2)x1
Speaker Box
Woofer
(B1)x8
M4x16mm
M4x16mm
CD-SW200E
3 – 4
[2] Removing and reinstalling the main parts
1. TAPE MECHANISM SECTION
Perform steps 1 to 5 and 6 of the disassembly method to remove the
tape mechanism. (See page3-1, 3-2)
tape mechanism. (See page3-1, 3-2)
1.1. How to remove the record/playback and erase heads
(TAPE 2) (See Fig. 1)
(TAPE 2) (See Fig. 1)
1. When you remove the screws (A1) x 2 pcs., the recording/play-
back head and three-dimensional head of the erasing head can be
removed.
removed.
Figure 1
1.2. How to remove the playback head (TAPE 1)(See Fig. 2)
1. When you remove the screws (B1) x 2 pcs., the playback head can
be removed.
Figure 2
1.3. How to remove the pinch roller (TAPE 1/2) (See Fig. 3)
1. Carefully bend the pinch roller pawl in the direction of the arrow
<A>, and remove the pinch roller (C1) x 1 pc., in the direction of the
arrow <B>.
arrow <B>.
Note:
When installing the pinch roller, pay attention to the spring mounting
position.
When installing the pinch roller, pay attention to the spring mounting
position.
Figure 3
1.4. How to remove the belt (TAPE 2) (See Fig. 4)
1. Remove the main belt (D1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (D2) x 1 pc.
1.5. How to remove the belt (TAPE 1) (See Fig. 4)
1. Remove the main belt (E1) x 1 pc., from the motor side.
2. Remove the FF/REW belt (E2) x 1 pc.
Figure 4
1.6. How to remove the motor (See Fig. 5)
1. Remove the screws (F1) x 2 pcs., to remove the motor.
Figure 5
(A1)x2
φ2x9mm
φ2x9mm
TAPE 2
Record/Playback
Head
Head
Erase Head
Clutch Ass'y
(B1)x2
φ
2x9mm
TAPE 1
Playback
Head
Head
Clutch Ass'y
Pinch Roller
(C1)x1
(C1)x1
<A>
<B>
Pinch
Roller
Pawl
Roller
Pawl
Pull
TAPE 2
TAPE 1
Main Belt
(E1)x1
Main Belt
(E1)x1
TAPE 2
Main Belt
(D1)x1
Main Belt
(D1)x1
TAPE 1
Main Belt
(D1)x1
(D1)x1
Main Belt
(E1)x1
(E1)x1
FF/REW
Belt
(D2)x1
Belt
(D2)x1
FF/REW
Belt
(E2)x1
Belt
(E2)x1
Tape
Motor
Tape
Motor
(F1)x2
φ
2.6x5mm
Tape
Motor
Motor
Clutch Ass'y
CD-SW200E
3 – 5
2. CD MECHANISM SECTION
Perform steps 1, 2, 9, 10 and 11 of the disassembly method to remove
the CD mechanism. (See page 3-1, 3-2)
the CD mechanism. (See page 3-1, 3-2)
2.1. Remove the pickup. (See Fig. 1)
1. Remove the stop washer (A1) x 1 pc., to remove the gear (A2) x 1
pc.
2. Remove the screws (A3) x 2 pcs., to remove the shaft (A4) x 1 pc.
3. Remove the pickup.
Note
After removing the connector for the optical pickup from the connector
wrap the conductive aluminium foil around the front end of connector
so as to protect the optical pickup from electrostatic damage.
After removing the connector for the optical pickup from the connector
wrap the conductive aluminium foil around the front end of connector
so as to protect the optical pickup from electrostatic damage.
Figure 1
3. CHANGER MECHANISM SECTION
Perform steps 1, 2, 9 and 10 of the disassembly method to remove the
CD changer mechanism.
CD changer mechanism.
3.1. How to remove CD Disc (See Fig. 2~5)
1. When CD is at play position (Figure 2), rotate reduction gear C
clock-wise as shown in Figure 3 until disc tray is at stock position,
then rotate further to eject the disc tray so that CD can be removed
from the tray.
then rotate further to eject the disc tray so that CD can be removed
from the tray.
Figure 2
Figure 3
2. In another case, if CD mechanism is at tray No.1 play position and
to remove CD located in tray No.3, the procedure is as follows:
If the gear up down board is located at tray No.1 position, then
rotate gear clock-wise until it at stock position. Rotate reduction
gear D clockwise (Figure 4) to move the CD mechanism to tray
No.3 position.This is confirmed by checking the gear up down
board position by the marking as indicated on the main chassis as
shown in Figure 5.
rotate gear clock-wise until it at stock position. Rotate reduction
gear D clockwise (Figure 4) to move the CD mechanism to tray
No.3 position.This is confirmed by checking the gear up down
board position by the marking as indicated on the main chassis as
shown in Figure 5.
Figure 4
Figure 5
Pickup Unit
(A3)x2
φ
2.6x6mm
CD Mechanism
Shaft
(A4)x1
(A4)x1
Gear
(A2)x1
(A2)x1
Stop Washer
(A1)x1
(A1)x1
CD Disc
CD At play position.
Disc Tray
Guide Tray
CD Disc
CD At stock position.
Reduction gear C
Front
Rear
Reduction gear D
Up
Down
Mark 1
(DISC 1)
(DISC 2)
(DISC 3)
(DISC 4)
(DISC 5)
Gear up down board
Mark 3
Mark 5
Mark 2
Mark 4
CD-SW200E
3 – 6
3.2. How to Remove the tray motor/main cam motor/5-
Changer Motor PWB (See Fig. 6)
Changer Motor PWB (See Fig. 6)
1. Remove the screws (A1) x 2 pcs., to remove tray motor/main cam
motor/5-Changer Motor PWB.
Figure 6
NOTE: There are 2 more screws tighten the motors at the bottom of
main chassis. Before performing procedure 1 above, disc stop
spring, top plate gear up down board and trays must be
removed, then only the 2 screws can be untighten.
spring, top plate gear up down board and trays must be
removed, then only the 2 screws can be untighten.
5-Changer
Motor PWB
Motor PWB
Tray Motor
Changer Mechanism Unit
Main Cam Motor
(A1)x2
φ2x10mm
φ2x10mm
Click on the first or last page to see other CD-SW200E (serv.man3) service manuals if exist.