DOWNLOAD Sharp CD-SW200E (serv.man3) Service Manual ↓ Size: 20.85 MB | Pages: 122 in PDF or view online for FREE

Model
CD-SW200E (serv.man3)
Pages
122
Size
20.85 MB
Type
PDF
Document
Service Manual
Brand
Device
Audio / System
File
cd-sw200e-sm3.pdf
Date

Sharp CD-SW200E (serv.man3) Service Manual ▷ View online

CD-SW200E
 
 – 0 –
SERVICE MANUAL
In the interests of user-safety the set should be restored to its
original condition and only parts identical to those specified be
used.
Note for users in U.K.
Recording and playback of any material may require consent
which SHARP is unable to give. Please refer particularly to the
provisions of Copyright Act 1956, the Dramatic and Musical
Performers Protection Act 1956, the Performers Protection Acts
1963 and 1972 and to any subsequent statutory enactments and
orders.
No. S6540CDSW200E
SHARP CORPORATION
CONTENTS
Parts marked with "
" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for
maintaining the safety and performance of the set.
CHAPTER 1. GENERAL DESCRIPTION
[1] Specifications ................................................. 1-1
[2]  Names of parts............................................... 1-2
CHAPTER 2. ADJUSTMENTS
[1] Mechanism 
section ........................................ 2-1
[2] Tuner 
section ................................................. 2-1
[3] TEST 
MODE .................................................. 2-2
[4] CD 
SECTION ................................................. 2-4
[5] CD 
section...................................................... 2-4
[6]  Standard Specification of Stereo System 
Error Message Display Contents ................... 2-4
[7]  CD Changer mechanism section ................... 2-5
CHAPTER 3. MECHANISM BLOCKS
[1] Caution 
on 
diassembly................................... 3-1
[2]  Removing and reinstalling the main parts 
........ 3-4
CHAPTER 4. DIAGRAMS
[1] Block 
diagrams............................................... 4-1
CHAPTER 5. CIRCUIT DESCRIPTION
[1]  Notes on schematic diagram .........................5-1
[2]  Types of transistor and LED ..........................5-1
[3]  Waveforms of CD circuit ................................5-2
[4] Voltage...........................................................5-3
CHAPTER 6. CIRCUIT SCHEMATICS AND PARTS
LAYOUT
[1] Schematic 
diagram........................................6-1
[2]  Wiring side of PWB...................................... 6-11
CHAPTER 7. FLOWCHART
[1] Troubleshooting .............................................7-1
CHAPTER 8. OTHERS
[1]  Function table of IC .......................................8-1
[2] FL 
Display......................................................8-9
Parts Guide
CD-SW200E
MODEL
CD-SW200E Mini Component System consisting of CD-SW200E
(main unit) CP-S200H (front speaker) and CP-SW200E (sub-
woofer).
MINI COMPONENT SYSTEM
CD-SW200E
 – i –
SAFETY PRECAUTION FOR SERVICE MANUAL
Precaution to be taken when replacing and servicing the Laser Pickup.
The AEL (Accessible Emission Level) of Laser Power Output for this model is specified to be lower than Class 1 Requirements.
However, the following precautions must be observed during servicing to protect your eyes against exposure to the Laser beam.
(1) When the cabinet has been removed, the power is turned on without a compact disc, and the Pickup is on a position outer than
the lead-in position, the Laser will light for several seconds to detect a disc. Do not look into the Pickup Lens.
(2) The Laser Power Output of the Pickup inside the unit and replacement service parts have already been adjusted prior to shipping.
(3) No adjustment to the Laser Power should be attempted when replacing or servicing the Pickup.
(4) Under no circumstances look directly into the Pickup Lens at any time.
(5) CAUTION - Use of controls or adjustments, or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
IMPORTANT SERVICE NOTES (FOR U.K. ONLY)
Before returning the unit to the customer after completion of a
repair or adjustment it is necessary for the following withstand
voltage test to be applied to ensure the unit is safe for the
customer to use.
Setting of Withstanding Voltage Tester and set.
Set name
set value
Withstanding Voltage Tester
Test voltage
4,240 VPEAK
3,000 VRMS
Set time
6 secs
Set current (Cutoff current)
4 mA
Unit
Judgment
OK: The "GOOD" lamp lights.
NG: The "NG" lamp lights and the buzzer sounds.
PROBE
AC
OUT
UNIT
SHORT-CIRCUIT
AC POWER
SUPPLY CORD
CONNECT THE PROBE
TO GND OF CHASSIS
SCREW
WITHSTANDING
VOLTAGE TESTER
Laser Diode Properties
Material: GaAIAs
Wavelength: 795 nm
Emission Duration: continuous
Laser Output: max. 0.6 mW
CD-SW200E
 
 – ii –
1. Employing lead-free solder
"Main/Display/Tumer/Power/Game Input/CD Servo PWB/LED" of this model employs lead-free solder. The LF symbol indicates
lead-free solder, and is attached on the PWB andservice manuals. The alphabetical character following LF shows the type of
lead-free solder.
Example:
Indicates lead-free solder of tin, silver and copper.
2. Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder
may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a
dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station
or service branch in your area.
3. Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C,
and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of
time. However, Since the land may be peeled off or the maximum heat-resistance temperature of parts may be exceeded,
remove the bit from the PWB as soon as you confirm the steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corrected. Make sure to turn on and off the
power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use
of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Ref No.
Description
Parts No.
PWB-A
92LPWB6383MANS
Main/Display
PWB-B
92LPWB6383PWRS
Power/Game Input
PWB-C
92LPWB6230CDUS
CD Servo
PWB-D
92LPWB6291TUNS
Tuner
PWB-E
92LPWB6230LEDS
LED
CD-SW200E
1 – 1
Audio
CD-SW200E
Service Manual
CD-SW200E
Market
E
 
CHAPTER 1. 
GENERAL DESCRIPTION
[1] Specifications
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER
TO THE OPERATION MANUAL.
Specifications for this model are subject to change without
prior notice.
CD-SW200E
CP-S200H
CP-SW200E
General
Amplifier
Power source
AC 230 - 240 V, 50 Hz
Power consumption 200 W
Dimensions
Width: 260 mm (10-1/4")
Height: 330 mm (13")
Depth: 326 mm (12-7/8")
Weight
10.4 kg (22.9 lbs.)
Output power
Front Speaker:
RMS: 200 W (100 W + 100 W) (10% T.H.D)
RMS: 156 W (78 W + 78 W) (0.9% T.H.D)
Subwoofer:
RMS: 200 W (10% T.H.D)
RMS: 166 W (0.9% T.H.D)
Output terminals
Front Speakers: 6 ohms
Subwoofer: 12 ohms
Headphones: 16 - 50 ohms
(recommended: 32 ohms)
Video output: 1Vp-p
Input terminals
Game/ Auxiliary (audio signal):
500 mV/ 47 k ohms
Game/Video: 1Vp-p
Type
5-disc multi-play compact disc player
Signal readout
Non-contact, 3-beam semiconductor laser
pickup
D/A converter
1-bit D/A converter
Frequency
response
20 - 20,000 Hz
Dynamic range
90 dB (1 kHz)
Frequency range
FM: 87.5 - 108.0 MHz
AM: 522 - 1,620 kHz
Frequency
response
50 - 14,000 Hz (normal tape)
Signal/noise ratio
55 dB (TAPE 1, playback)
50 dB (TAPE 2, recording/playback)
Wow and flutter
0.3 % (WRMS)
Type
3-way type speaker system
Super tweeter
5 cm (2") tweeter
13 cm (5-1/8") woofer
Maximum input
power
200 W
Rated input power
100 W
Impedance
6 ohms
Dimensions
Width: 180 mm (7-1/16")
Height: 330 mm (13")
Depth: 212 mm (8-6/16")
Weight
3.0 kg (6.6 lbs.) /each
Type
Full Range
20 cm (8") subwoofer
Maximum input
power
400 W
Rated input power
200 W
Impedance
12 ohms
Dimensions
Width: 250 mm (9-13/16")
Height: 330 mm (13")
Depth: 294 mm (11-9/16")
Weight
5.9 kg (13 lbs.)
CD player
Tuner
Cassette deck
Page of 122
Display

Sharp CD-SW200E (serv.man3) Service Manual ▷ Download

  • DOWNLOAD Sharp CD-SW200E (serv.man3) Service Manual ↓ Size: 20.85 MB | Pages: 122 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sharp CD-SW200E (serv.man3) in PDF for free, which will help you to disassemble, recover, fix and repair Sharp CD-SW200E (serv.man3) System. Information contained in Sharp CD-SW200E (serv.man3) Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.