DOWNLOAD Sharp CD-BA3100 (serv.man9) Service Manual ↓ Size: 5.42 MB | Pages: 76 in PDF or view online for FREE

– 17 –

During POWER OFF mode, push below each 2 keys and [POWER] key. Then go to each Test Mode.

KEY

TEST MODE

CONTENTS

[CD] [X-BASS] + [POWER]

TEST 1

CD Test mode

[TAPE] [X-BASS] + [POWER]

TEST 2

Tape test mode

[TUNER] [X-BASS] + [POWER]

TEST 3

Tuner preset memory clear

[VIDEO/AUX] [X-BASS] + [POWER]

TEST 4

Tuner preset for production

[MEMORY/SET] [X-BASS] + [POWER]

TEST 5

All clear (reset)

[EQUALIZER] [X-BASS] + [POWER]

TEST 6

Audio test

[   ] [DIMMER] + [POWER]

TEST 7

Key and display test

[TUN UP] [DIMMER] + [POWER]

TEST 8

RDS Test1

[TUN DOWN] [DIMMER] + [POWER]

TEST 9

RDS Test2

[ 

 ] [CD] + [POWER]

TEST 10

CD Changer test

[ 

 ] [CD] + [POWER]

TEST 11

Production initialize for changer

[EQUALIZER] [TUN UP] + [POWER]

TEST 12

Graphic equalizer test

• Setting the test mode
  Any one of test mode can be set by pressing several keys as follows.
  <X-BASS> + <CD> + <POWER> TEST: CD operation test.

Enter test 1 mode key.

C  D       T  E  S  T

OPEN/CLOSE operation is using manual.

Do TOC IL. Do normal play.
When these following key is input into PLAY key,
track number  can be appoint directly.

<<PLAY>> key input.

<<MEMORY>> key input.

Laser ON.

<<MEMORY>> key input.

Tracking OFF play at that specific point.

<<MEMORY>> key input.

<<

1>> key: Track 1

<<

2>> key: Track 3

<<

3>> key: Track 7

<<

4>> key: Track 11

<<

5>> key: Track 13

<<

6>> key: Track 15

Tracking ON play from that specific point.

<<MEMORY>> key input

a) Display

"FOFF_XX"

b) Display

"TOFF_XX"

c) Display

"TBAL_XX"

d) Display

"TGAN_XX"

e) Display

"FGAN_XX"

 f) Display

"RFLS_XX"

<< 

 >>, << 

 >> buttons make pick's slide possible.

<<STOP>> key input.

STOP

<<MEMORY>> key input.

a) Display

"FOFF_XX"

b) Display

"TOFF_XX"

c) Display

"TBAL_XX"

d) Display

"TGAN_XX"

e) Display

"FGAN_XX"

 f) Display

"RFLS_XX"

Display every auto setting result for every 2 sec.

<<STOP>> key input.

STOP

VOL

––

Last memory

BAL

––

CENTER

P.GEQ

––

FLAT

X-BASS

––

OFF

Sliding the PICKUP with
<< 

 >>, << 

 >> button

must only be in STOP mode.

Display each step for 2 sec.      XX: HEX VALUE
a) "FOFF_XX"

Focus off set

b) "TOFF_XX"

Tracking off set

c) "TBAL_XX"

Tracking balance

d) "TGAN_XX"

Tracking gain

e) "FGAN_XX"

Focus gain

f ) "RFLS_XX"

RF level shift

To cancel : Power OFF

– 18 –

1. Motor assembly (x 2) mounting (screw x 4)

01/29

Fig.19

2. MT idle gear mounting (screw x 1)

25

Fig.19

3. MT system gear assembly

23/24/26/27

Fig.19

4. STB/tray drive system gear and others assembling/

37/38/45/46 (53)/47/48

Fig.19

    mounting (screw x 3)

5. Tray big gear assembly

31

Fig.19

Gear positioning

6. T.M SW PWB mounting (screw x 3)

Fig.20

7. STB holder assembling

03

Fig.19

8. STB drive gear L/R assembly mounting (screw x 2)

11 (10)/12 (10)

Fig.19

9. Tray joint gear R/tray drive gear R assembling

34/36

Fig.20

Gear positioning

10. Tray gear A/B assembling

32/33

Fig.20

Gear positioning

11. Lift gear B/C assembling

43/44

Fig.21

Gear positioning

12. MT idler gear F assembling, mode big gear

28/42

Fig.21

      mounting (screw x 1)

13. Change box R mounting (screw x 4)

04

Fig.21

14. Lift gear A assembling

42

Fig.21

Gear positioning

15. Change box L assembly mounting (screw x 4)

02/30/35

Fig.22

16. Lift cam assembling (shaft inserting)

44

Fig.22

Gear positioning

17. STB holder height adjusting

Fig.23

Check/adjustment

18. Top plate F/disc OB LEV. Mounting (screw x 6)

80

Fig.23

19. Trays 1 - 6 assembling

91/92/93/94/95/96

Fig.24

20. Top plate R mounting (screw x 6)

––

01 (101)

MAIN BASE

02 (102)

CHANGE BOX L

03 (147)

STB HOLDER

04 (103)

CHANGE BOX R

10 (119)

STB DRIVE GEAR A

11 (120)

STB DRIVE GEAR L

12 (122)

STB DRIVE GEAR R

20 (149)

STABILIZER FH

23 (141)

MT IDLER GEAR A

24 (138)

MT IDLER GEAR B

25 (137)

MT IDLER GEAR C

26 (140)

MT IDLER GEAR D

27 (139)

MT IDLER GEAR E

28 (131)

MT IDLER GEAR F

29 (MOB1,2)

MOTOR GEAR

30 (143)

TRAY DRIVE GEAR F

31 (134)

TRAY BIG GEAR

32 (135)

TRAY GEAR A

33 (136)

TRAY GEAR B

34 (124)

TRAY DRIVE GEAR R

35 (144)

TRAY JOINT GEAR F

36 (125)

TRAY JOINT GEAR R

37 (142)

TRAY GEAR C

38 (130)

TRAY IDLER GEAR

40 (115)

LIFT CAM

41 (126)

MODE BIG GEAR

42 (127)

LIFT GEAR A

43 (128)

LIFT GEAR B

44 (129)

LIFT GEAR C

45 (132)

STB GEAR A

46 (104)

STB GEAR B

47 (133-1)

STB GEAR C

48 (133-3)

STB GEAR D

50 (145)

LIFT LEVER

51 (106)

TRAY LOCK LEVER

52 (118)

DISC OB LEVER

53 (105)

STB GEAR ANG.

80 (117)

TOP PLATE F

81 (114)

TOP PLATE R

91 (108)

TRAY 1

92 (109)

TRAY 2

93 (110)

TRAY 3

94 (111)

TRAY 4

95 (112)

TRAY 5

96 (113)

TRAY 6

The number of (  ) is the number of the parts guide.

– 19 –

03
STB HOLDER

48
STB GEAR D

12

STB DRIVE GEAR R

(ASSY)

10

STB DRIVE GEAR A

29

29

23

23

24

25

26

27

01
MAIN BASE

Mark position

After assembling TRAY BIG GEAR, turn it in the arrow direction.

TRAY BIG GEAR ASSEMBLING POSITION 

31
TRAY BIG GEAR

37
TRAY GEAR C

38
TRAY IDLER GEAR

47

STB GEAR C

46

STB GEAR B

10

STB DRIVE GEAR A

11

STB DRIVE GEAR L

(ASSY)

53

STB GEAR ANG.

45

STB GEAR A

11(/12)  (10)
STB DRIVE GEAR L(/R)
(ASS'Y)

46

STB GEAR B

37
TRAY GEAR C

47

STB GEAR C

31

TRAY BIG GEAR

38

TRAY IDLER GEAR

45

STB GEAR A

53

STB GEAR ANG.

L

– 20 –

31

M T SW PWB

33
TRAY
GEAR B

32
TRAY GEAR A

33

TRAY GEAR B

37

32
TRAY GEAR A

38

34
TRAY DRIVE GEAR R

36
TRAY  JOINT GEAR R

47

46

34
TRAY DRIVE GEAR R

36
TRAY JOINT GEAR R

10

29

29

23

23

24

25

26

27

Mark position

11

45

TRAY BIG GEAR SET POSITION

33

32

Direct the recess part 
(trapezoidal side) of the axis 
35 in this direction.

* This position becomes the 
   reference (stock) position 
   of the tray.

These holes must align.

It must not rotate in contact 
with the peripheral (hatched) 
part of 31.

These holes must align.

After assembling 32, 
assemble 33.

*1: To position the axis part of 36, engage it with 38.
*2: When it is aligned as described in *1, the hatched part 
     (low gear-height part of gear) will be positioned in this position.
Note: After positioning the tray big gear in the set position, engage these gears.

*1

*2

Scale: 2 magnifications

Scale: 2 magnifications

LL