DOWNLOAD Sharp CD-BA1200 (serv.man6) Service Manual ↓ Size: 582.59 KB | Pages: 14 in PDF or view online for FREE

Model
CD-BA1200 (serv.man6)
Pages
14
Size
582.59 KB
Type
PDF
Document
Service Manual
Brand
Device
Audio / System / Part 1 - text
File
cd-ba1200-sm6.pdf
Date
PREV: Sharp CD-BA1200 (serv.man5) Service Manual

Sharp CD-BA1200 (serv.man6) Service Manual ▷ View online

– 13 –
CD-BA1200H
How to remove the pickup (See Fig. 13-2)
1. Remove the screws (B1) x 2 pcs., to remove the shaft (B2).
2. Remove the stop washer (B3) x 1 pc., to remove the gear
(B4).
3. Remove the pickup.
Figure 13-2
CD MECHANISM SECTION
Perform steps 1, 2, 3, 9 and 12 of the disassembly method to
remove the CD mechanism.
How to remove the loading motor
(See Fig. 13-1)
1. Bend the hooks (A1) x 5 pcs., to remove the loading motor.
Figure 13-1
Note
After removing the connector for the optical pickup from the
connector, wrap the conductive aluminium foil around the
front end of connector to protect the optical pickup from
electrostatic damage.
(A1)x2
(A1)x1
Loading Motor
Slide Chassis
(A1)x2
(B1) x2
  ø2.6 x6mm
Shaft
(B2) x1
Stop Washer
(B3) x1
Gear
(B4) x1
CD Mechanism
Pickup
ADJUSTMENT
MECHANISM SECTION
•
 Driving Force Check
Torque Meter
Specified Value
Play: TW-2111
Tape 1: Over 80 g
Tape 2: Over 80 g
•
 Torque Check
Torque Meter
Tape 2
Play: TW-2111
30 to 80 g.cm
30 to 80 g.cm
Fast forward: TW-2231
—
70 to 180 g.cm
Rewind: TW-2231
—
70 to 180 g.cm
Specified Value
Tape 1
Specified
Value
Adjusting
Point
Instrument
Connection
Test Tape
Normal
MTT-111
Variable
3,000 
±
Speaker
speed
Resistor in
30 Hz
terminal
motor.
(Load
resistance:
6 ohms)
•
 Tape Speed
Figure 13-3
TAPE MECHANISM
Motor
Variable Resistor
in motor
CD-BA1200H
– 14 –
CD SECTION
• 
 AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
*1. Input: Antenna
Output: TP302
*2. Input: Antenna
Output: TP301
TUNER SECTION
fL: Low-range frequency
fH: High-range frequency
AM IF
450 kHz
1,620 kHz
T351
*1
AM Band
—
522 kHz
(fL): T306
*2
Coverage
1.1 
±
 0.1 V
AM Tracking 990 kHz
990 kHz
(fL): T303
*1
Figure 14-1 ADJUSTMENT POINTS
Test Stage
Frequency
Frequency
Display
Setting/
Adjusting
Parts
Instrument
Connection
T306
T303
R357
TP301
TP302
T351
AM IF
AM
TRACKING fL
AM BAND
COVERAGE fL
FE301
SO301
FM ANTENNA
TERMINAL
CNP302
AM LOOP
ANTENNA
MAIN PWB
1
R381
Figure 14-2
CD ERROR CODE DESCRIPTION
Error
State Code
[Servo System Error]
0001
Cannot detect Pickup-in SW
0002
DSP access error
[Error during close operation]
0101
Open/Close SW Low 
→ 
High not functioning
0103
Open/Close SW High 
→
 Low not functioning
[Error during open operation]
0201
Open/Close SW Low 
→ 
High not functioning
0203
Open/Close SW High 
→
 Low not functioning
[Error during skip operation]
0302
Pickup-in SW is not detected
0306
During Disc 1 search, Open/Close SW or Clamp SW
or Disc SW do not change to low.
0307
Clamp SW Low 
→ 
High not functioning
0308
Clamp SW High 
→
 Low not functioning
Items adjusted automatically
(1) Offset adjustment (The offset voltage between the head
amplifier output and the VREF reference voltage is
compensated inside the IC.)
  * Focus offset adjustment
  * Tracking offset adjustment
(2) Tracking balance adjustment (waveform drawing Fig.
14-2 EFBL)
(3) Gain adjustment (The gain is compensated inside the IC
so that the loop gain at the gain crossover frequency will
be 0dB.)
  * Focus gain adjustment
  * Tracking gain adjustment
•  Adjustment
T
T
EFBL
FDO
TE
Stopped
CH1=500mV
DC   10:1
CH2=200mV
DC   10:1
CH3=1V
DC   10:1
500ms/div
(500ms/div)
NORM:20kS/s
1
2
3
=Record Length=
Smoothing :   ON
CH1  :      0.000V
CH2  :      0.000V
Main  :     100K
Zoom  :       2k
Mode  :   SINGLE
Type   :   EDGE CH1
Delay  :                    0.0ns
Hold off  :                0.2us
CH3  :        0.00V
CH4  :        0.00V
BW   : FULL
=Trigger=
=Filter=
=Offset=
CH2
  v/DIV
   200mV
1999/04/05  20:26:47
•  FM
Notes:
1: Description of the "FM IF Adjustment" is not carried on this
Manual. It is because the IF coil in the FM front end section
has been best adjusted in the factory so that its further
adjustment is not needed at the field. When replacing the
FM front end assembly, no adjustment is needed either.
2: The parts in the FM front end section are prepared in a
complete unit, so you can't obtain each part individually
CD-BA1200H
– 14 –
CD SECTION
• 
 AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
*1. Input: Antenna
Output: TP302
*2. Input: Antenna
Output: TP301
TUNER SECTION
fL: Low-range frequency
fH: High-range frequency
AM IF
450 kHz
1,620 kHz
T351
*1
AM Band
—
522 kHz
(fL): T306
*2
Coverage
1.1 
±
 0.1 V
AM Tracking 990 kHz
990 kHz
(fL): T303
*1
Figure 14-1 ADJUSTMENT POINTS
Test Stage
Frequency
Frequency
Display
Setting/
Adjusting
Parts
Instrument
Connection
T306
T303
R357
TP301
TP302
T351
AM IF
AM
TRACKING fL
AM BAND
COVERAGE fL
FE301
SO301
FM ANTENNA
TERMINAL
CNP302
AM LOOP
ANTENNA
MAIN PWB
1
R381
Figure 14-2
CD ERROR CODE DESCRIPTION
Error
State Code
[Servo System Error]
0001
Cannot detect Pickup-in SW
0002
DSP access error
[Error during close operation]
0101
Open/Close SW Low 
→ 
High not functioning
0103
Open/Close SW High 
→
 Low not functioning
[Error during open operation]
0201
Open/Close SW Low 
→ 
High not functioning
0203
Open/Close SW High 
→
 Low not functioning
[Error during skip operation]
0302
Pickup-in SW is not detected
0306
During Disc 1 search, Open/Close SW or Clamp SW
or Disc SW do not change to low.
0307
Clamp SW Low 
→ 
High not functioning
0308
Clamp SW High 
→
 Low not functioning
Items adjusted automatically
(1) Offset adjustment (The offset voltage between the head
amplifier output and the VREF reference voltage is
compensated inside the IC.)
  * Focus offset adjustment
  * Tracking offset adjustment
(2) Tracking balance adjustment (waveform drawing Fig.
14-2 EFBL)
(3) Gain adjustment (The gain is compensated inside the IC
so that the loop gain at the gain crossover frequency will
be 0dB.)
  * Focus gain adjustment
  * Tracking gain adjustment
•  Adjustment
T
T
EFBL
FDO
TE
Stopped
CH1=500mV
DC   10:1
CH2=200mV
DC   10:1
CH3=1V
DC   10:1
500ms/div
(500ms/div)
NORM:20kS/s
1
2
3
=Record Length=
Smoothing :   ON
CH1  :      0.000V
CH2  :      0.000V
Main  :     100K
Zoom  :       2k
Mode  :   SINGLE
Type   :   EDGE CH1
Delay  :                    0.0ns
Hold off  :                0.2us
CH3  :        0.00V
CH4  :        0.00V
BW   : FULL
=Trigger=
=Filter=
=Offset=
CH2
  v/DIV
   200mV
1999/04/05  20:26:47
•  FM
Notes:
1: Description of the "FM IF Adjustment" is not carried on this
Manual. It is because the IF coil in the FM front end section
has been best adjusted in the factory so that its further
adjustment is not needed at the field. When replacing the
FM front end assembly, no adjustment is needed either.
2: The parts in the FM front end section are prepared in a
complete unit, so you can't obtain each part individually
CD-BA1200H
– 14 –
CD SECTION
• 
 AM IF/RF
Signal generator: 400 Hz, 30%, AM modulated
*1. Input: Antenna
Output: TP302
*2. Input: Antenna
Output: TP301
TUNER SECTION
fL: Low-range frequency
fH: High-range frequency
AM IF
450 kHz
1,620 kHz
T351
*1
AM Band
—
522 kHz
(fL): T306
*2
Coverage
1.1 
±
 0.1 V
AM Tracking 990 kHz
990 kHz
(fL): T303
*1
Figure 14-1 ADJUSTMENT POINTS
Test Stage
Frequency
Frequency
Display
Setting/
Adjusting
Parts
Instrument
Connection
T306
T303
R357
TP301
TP302
T351
AM IF
AM
TRACKING fL
AM BAND
COVERAGE fL
FE301
SO301
FM ANTENNA
TERMINAL
CNP302
AM LOOP
ANTENNA
MAIN PWB
1
R381
Figure 14-2
CD ERROR CODE DESCRIPTION
Error
State Code
[Servo System Error]
0001
Cannot detect Pickup-in SW
0002
DSP access error
[Error during close operation]
0101
Open/Close SW Low 
→ 
High not functioning
0103
Open/Close SW High 
→
 Low not functioning
[Error during open operation]
0201
Open/Close SW Low 
→ 
High not functioning
0203
Open/Close SW High 
→
 Low not functioning
[Error during skip operation]
0302
Pickup-in SW is not detected
0306
During Disc 1 search, Open/Close SW or Clamp SW
or Disc SW do not change to low.
0307
Clamp SW Low 
→ 
High not functioning
0308
Clamp SW High 
→
 Low not functioning
Items adjusted automatically
(1) Offset adjustment (The offset voltage between the head
amplifier output and the VREF reference voltage is
compensated inside the IC.)
  * Focus offset adjustment
  * Tracking offset adjustment
(2) Tracking balance adjustment (waveform drawing Fig.
14-2 EFBL)
(3) Gain adjustment (The gain is compensated inside the IC
so that the loop gain at the gain crossover frequency will
be 0dB.)
  * Focus gain adjustment
  * Tracking gain adjustment
•  Adjustment
T
T
EFBL
FDO
TE
Stopped
CH1=500mV
DC   10:1
CH2=200mV
DC   10:1
CH3=1V
DC   10:1
500ms/div
(500ms/div)
NORM:20kS/s
1
2
3
=Record Length=
Smoothing :   ON
CH1  :      0.000V
CH2  :      0.000V
Main  :     100K
Zoom  :       2k
Mode  :   SINGLE
Type   :   EDGE CH1
Delay  :                    0.0ns
Hold off  :                0.2us
CH3  :        0.00V
CH4  :        0.00V
BW   : FULL
=Trigger=
=Filter=
=Offset=
CH2
  v/DIV
   200mV
1999/04/05  20:26:47
•  FM
Notes:
1: Description of the "FM IF Adjustment" is not carried on this
Manual. It is because the IF coil in the FM front end section
has been best adjusted in the factory so that its further
adjustment is not needed at the field. When replacing the
FM front end assembly, no adjustment is needed either.
2: The parts in the FM front end section are prepared in a
complete unit, so you can't obtain each part individually
Page of 14
Display

Sharp CD-BA1200 (serv.man6) Service Manual ▷ Download

Found More:

CD-BA1200 (serv.man6) Service Manuals

Preview DownloadPagesSize
CD-BA1200 (serv.man5) Video clip detailing how to re-install the 3 CD changer mechanism Service Manual 4.04 MB
CD-BA1200 (serv.man7) Part 2 - Notes on diagrams, Waveforms, Block diagrams Service Manual 5 427.55 KB
CD-BA1200 (serv.man8) Part 3 - Schematic Diagrams Service Manual 10 615.97 KB
CD-BA1200 (serv.man9) Part 4 - Printed wiring board assemblies Service Manual 6 672.93 KB
CD-BA1200 (serv.man10) Part 5 - Voltage table, Troubleshooting table, IC table Service Manual 13 403.1 KB
CD-BA1200 (serv.man11) Including circuit diagrams Service Manual 60 2.92 MB
CD-BA1200 (serv.man2) Quick Start Guide User Manual / Operation Manual 4 131.96 KB
CD-BA1200 (serv.man3) part (from the ) User Manual / Operation Manual 1 53.3 KB
CD-BA1200 User Manual / Operation Manual 27 1.31 MB
CD-BA1200 (serv.man4) Service Manual / Parts Guide 12 307.35 KB
CD-BA1200 (serv.man12) Service Manual / Specification 1 22.44 KB
CD-BA1200 (serv.man13) Tape deck Service Manual / Technical Bulletin 2 25.51 KB
CD-BA1200 (serv.man14) C946 can fail when the AC supply varies by a significant amount Service Manual / Technical Bulletin 1 9.97 KB
CD-BA1200 (serv.man15) Tape error on display Service Manual / Technical Bulletin 2 158.59 KB
CD-BA1200 (serv.man16) Parts assigned as service parts Service Manual / Technical Bulletin 1 41.4 KB
CD-BA1200 (serv.man17) Addition of screws to CD player to prevent seizure Service Manual / Technical Bulletin 2 80.54 KB
CD-BA1200 (serv.man18) Addition of screws for CD player to prevent seizure Service Manual / Technical Bulletin 2 83.02 KB
CD-BA1200 (serv.man19) Fly wheels assigned as service parts. Service Manual / Technical Bulletin 1 66.95 KB
CD-BA1200 (serv.man20) Part setting for separate items in cassette mechansim. Service Manual / Technical Bulletin 1 69.32 KB
CD-BA1200 (serv.man21) Correction to printing error in (Belt). Service Manual / Technical Bulletin 1 66.4 KB

RANDOM: