Sharp AN-PR1100H Service Manual ▷ View online
AN-PR1100H
1 – 3
[5] Names Of Parts
Main Unit (front panel)
1. Left Front Speakers
2. Top glass cover
3. Right Front Speakers
4. Right Subwoofer
5. Display
6. Wooden shelf
7. Left Subwoofer
8. On/Stand-by Button
9. Function Button
10. Timer Indicator
11. Remote Sensor
12. Volume Up and Down Buttons
2. Top glass cover
3. Right Front Speakers
4. Right Subwoofer
5. Display
6. Wooden shelf
7. Left Subwoofer
8. On/Stand-by Button
9. Function Button
10. Timer Indicator
11. Remote Sensor
12. Volume Up and Down Buttons
Main Unit (rear panel)
1. Speaker Terminal
2. Bass Reflex Duct
2. Bass Reflex Duct
1. Optical Digital Audio Input Sockets
2. Coaxial Digital Audio Input Socket
3. Audio Line Input Sockets
4. AC Power Input Socket
5. Cooling Fan
6. Subwoofer Pre Output Socket
7. FM 75 Ohms Aerial Socket
2. Coaxial Digital Audio Input Socket
3. Audio Line Input Sockets
4. AC Power Input Socket
5. Cooling Fan
6. Subwoofer Pre Output Socket
7. FM 75 Ohms Aerial Socket
Display
1. Mono to Stereo indicator
2. Intelligent Volume indicator
3. Natural Bass indicator
4. Sound Space indicator
5. Dynamic PTY indicator
6. Traffic Announcement indicator
7. RDS indicator
8. Traffic Programme indicator
9. Dolby Digital Signal indicator
10. FM Stereo Mode indicator
11. DTS Signal indicator
12. Dolby Virtual Sound indicator
13. Timer indicator
14. FM Stereo Receiving indicator
15. Dolby Prologic II indicator
16. Sleep indicator
2. Intelligent Volume indicator
3. Natural Bass indicator
4. Sound Space indicator
5. Dynamic PTY indicator
6. Traffic Announcement indicator
7. RDS indicator
8. Traffic Programme indicator
9. Dolby Digital Signal indicator
10. FM Stereo Mode indicator
11. DTS Signal indicator
12. Dolby Virtual Sound indicator
13. Timer indicator
14. FM Stereo Receiving indicator
15. Dolby Prologic II indicator
16. Sleep indicator
ON
/
ST
AN
D-
BY
VO
LU
M
E +
RE
M
OT
E
SE
NS
OR
VO
LU
M
E
–
FU
NC
TI
ON
TI
M
ER
2
8
9
10
11
12
3
4
1
5
6
7
1
2
1
4
5
6
7
2
3
9
10
11
8
7
6
5
1
2
3
4
3
4
13 14
16
15
12
AN-PR1100H
1 – 4
Remote control
2
1
12
15
5
7
16
17
13
14
3
4
6
10
9
8
11
19
18
21
22
20
1. Remote Control Transmitter
2. ON/STAND-BY button
3. Input Select Buttons
4. Audistry Sound Mode Buttons
5. Tuner Preset Down Button
6. DVD Player Operation Buttons
7. Tuning Down Button
8. TV Operation Buttons
9. Tuner Button
2. ON/STAND-BY button
3. Input Select Buttons
4. Audistry Sound Mode Buttons
5. Tuner Preset Down Button
6. DVD Player Operation Buttons
7. Tuning Down Button
8. TV Operation Buttons
9. Tuner Button
10. Shift Button
11. Dimmer Button
12. Preset Sound Mode / Clock / Timer Button
13. Dolby Virtual Speaker Button
14. Volume Up and Down/
11. Dimmer Button
12. Preset Sound Mode / Clock / Timer Button
13. Dolby Virtual Speaker Button
14. Volume Up and Down/
Subwoofer Level Up and Down Buttons
15. Mute/Display Button
16. Tuner Preset Up Button
17. Tuning Up Button
18. Direct Number Buttons
19. Clear Button
20. RDS ASPM Button
21. RDS Display Button
22. RDS PTYI Button
16. Tuner Preset Up Button
17. Tuning Up Button
18. Direct Number Buttons
19. Clear Button
20. RDS ASPM Button
21. RDS Display Button
22. RDS PTYI Button
DVD Player Operation Buttons
ON/STAND-BY button
Menu/Top Menu Button
Sets the DVD power to
"ON" or "STAND- BY".
"ON" or "STAND- BY".
Press to display the
menu.
menu.
TV Operation Buttons
Cursor Buttons
Return Button
Volume Up and Down Buttons
Press the button to
select menus and items.
select menus and items.
Press the button to
return to the previous
step.
return to the previous
step.
Turn down/up the TV
volume.
volume.
Review/Cue Buttons
Play Button
Channel Up and Down Buttons
Press to go backward
or forward (search).
or forward (search).
Play back the DVD
player.
player.
Switch down/up the TV
channels.
channels.
Chapter (Track) Skip Down/Up Buttons
Stop Button
Input Select Button (TV/VCR)
Skip down/up the DVD
chapters (tracks).
chapters (tracks).
Stops the DVD player.
Press the button to switch
the input source.
the input source.
Enter Button
Pause Button
ON/STAND-BY button
Press to set a menu or
an item.
an item.
Press to pause.
Sets the TV power to
"ON" or "STAND-BY".
"ON" or "STAND-BY".
Repeat Play Button
Press to repeat
playback.
playback.
AN-PR1100H
2 – 1
CD-ES700/CD-ES77
CD-ES700/CD-ES77
Service Manual
CD-ES700/CD-ES77
Market
E
CHAPTER 2. ADJUSTMENTS
[1] Description Of Error Messages
* For other error messages using STANDBY LED, refer to the corresponding pages.
Error message
Cause
Solution
“ERR 01”
(Appears for 2 seconds and then the system
goes standby.)
(Appears for 2 seconds and then the system
goes standby.)
• Rotation stop of the fan motor
• Check if the fan motor cord is inserted
properly and the fan motor is not locked.
“ERR 02”
(When this error is not detected, the initial
display appears.)
(When this error is not detected, the initial
display appears.)
• Error in the ICM6 (CS49510) control
• Unplug the AC power cord and turn on
power again.
• Check the line connected between ICM6
and ICM7.
“ERR 03”
(When this error is not detected, the initial
display appears.)
(When this error is not detected, the initial
display appears.)
• Internal communication error of the system
[ICA1 (WM8775) or ICM3 (CS8416CN)]
• Unplug the AC power cord and turn on
power again.
• Check the line connected among ICA1,
ICM3, ICM8 and ICM7.
“ERR 07”
(When this error is not detected, the initial
display appears.)
(When this error is not detected, the initial
display appears.)
• Internal communication error of the system
[ICM10 (LC750512)]
• Unplug the AC power cord and turn on
power again.
• Check the line connected between ICM10
and ICM7.
“ERR 80”
(When this error is not detected, the initial
display appears.)
(When this error is not detected, the initial
display appears.)
• Internal data read access error of ICM8
(CAT24WC05YI)
• Check EEPROM data.
• Replace EEPROM IC (ICM8).
• Replace EEPROM IC (ICM8).
AN-PR1100H
2 – 2
[2] Test Mode
1. Entering the test mode
In the AC OFF state, hold down the “FUNCTION” key and press the
POWER key. Then switch on AC to enter the test mode route state.
In the AC OFF state, hold down the “FUNCTION” key and press the
POWER key. Then switch on AC to enter the test mode route state.
* Be sure to follow the above procedure to enter the test mode.
2. Exiting the test mode
In the test mode route state, press the POWER key to turn off the
system and exit the test mode.
In the test mode route state, press the POWER key to turn off the
system and exit the test mode.
3. Operation
(Test mode start-up operation)
4. Remote control key operation
Key operation is described by using the names of the main unit keys.
For remote control key operation, each test can be enter directly as
follow.
Key operation is described by using the names of the main unit keys.
For remote control key operation, each test can be enter directly as
follow.
* However, remote control keys are unavailable for starting the test
mode.
* Remote control keys are unavailable for starting the test mode.
[3] EEPROM Mode
When replacing EEPROM IC, necessary data are not recorded
inside; “Protect area read error” (“ERR 80”) occurs.
inside; “Protect area read error” (“ERR 80”) occurs.
To avoid this state, write the data into the corresponding device.
1. Enter the test mode and check set data values of each address
according to the EEPROM set data table on the right.
If necessary, change the set data values.
If necessary, change the set data values.
NOTE: (Data are written into EEPROM in the procedure 4 below.)
(Do not stop power supply to the product)
2. Exiting the EEPROM mode from the address value display state.
(Press the POWER key once in the address value display state.)
(The product enters the test mode route state.)
3. Exiting the test mode
(Press the POWER key once in the test mode route state.)
(Then the data are written into EEPROM. After the write
operation, the product enters the standby state.)
operation, the product enters the standby state.)
4. After checking that the product enters the standby state, stop
power supply to the product.
(This operation initializes the error state.)
* Operation ends.
AN0629AH
↓
GOOD BYE
↓
(POWER key)
Version Display
(example version date is
29/06/2006)
(example version date is
29/06/2006)
Display “GOOD BYE”
(as in the case of the user
mode)
(as in the case of the user
mode)
Remote Control Key
Test Mode
MUTE key
Volume Test
DVS key
Key Test
SOUND MODE key
EEPROM Mode Test
TUNER key
Tuner Test
ASPM key
ASPM Test
AN0629AH
EEP TEST
↓
(VOLUME key)
↑ ↓
Test mode route state
(Example Micom version date 29/6/2006)
(Example Micom version date 29/6/2006)
EEP 025A
↓
EEP 025B
↑ ↓
EEP 025C
↑ ↓
EEP 03FF
↑ ↓
EEP 03FE
Mode menu “EEPROM“
(VOLUME + key): EEPROM mode start-up
(VOLUME + key): EEPROM mode start-up
EEPROM address display (25Ah)
(VOLUME + key): Address increment
(VOLUME + key): Address increment
EEPROM address display (25Bh)
EEPROM address display (3FF h)
↑ ↓
EEP 005A
←
→
(Input select key)
At each address
(Input select key)
(Set value change by
VOLUME +/– keys)
VOLUME +/– keys)
Set data value display
(2 Hz flasing)
Click on the first or last page to see other AN-PR1100H service manuals if exist.