Panasonic TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C Service Manual ▷ View online
HOW TO MOVE THE CHASSIS
INTO SERVICE POSITION
INTO SERVICE POSITION
1. Remove the bead clamper from the mains lead.
2. Hold and lift the rear of the chassis and gently pull
2. Hold and lift the rear of the chassis and gently pull
the chassis towards you, as shown in
Fig.4.
3. Release the respective wiring clips and rotate the
chassis horizontally through 90° anti-clockwise and
elevate the front of the chassis.
elevate the front of the chassis.
4. Using
the
rib
(A), as shown
Fig .5.
, locate the
chassis to position
Fig .6.
5. After servicing ensure all wiring is returned to its
original position before returning the receiver to the
customer.
customer.
SERVICE POSITION
FÜR DAS CHASSIS
FÜR DAS CHASSIS
1. Beseitigen sie das Festklemmen der Hauptleiter.
2. Ergreifen sie den Hinterteil von Chassis und ziehen sie
2. Ergreifen sie den Hinterteil von Chassis und ziehen sie
leicht das Chassis in der Richtung zu Ihnen
Abb. 4.
.
3. Lösen sie die Klemmen von einschlägigen Leitern
(Dräten) und drehen sie das Chassis horizontal um
90
90
° gegen Uhrzeigersinn, dann heben sie den
Vorderteil von Chassis nach oben.
4. Mit der Hilfe der Rippe (A),
Abb.5.
, plazieren sie das
Chassis in die Lage auf dem
Abb.6.
.
5. Vor Rückgabe von TV an den Kunden versichen sie,
dass alle Leiter in ihre ursprünglichen Positionen
zurückgebracht werden
zurückgebracht werden
.
5
Fig.4 .
Abb.4.
Fig. 6.
Abb.6.
Fig.5 .
Abb.5.
(A)
(A)
SELF CHECK
1. Self-check is used to automatically check the bus
lines and hexadecimal code of the TV set.
2. To get into the Self-Check mode press the down
(-/v) button on the customer controls at the front of
the set, at the same time pressing the STATUS
button on the remote control, and the screen will
show :
the set, at the same time pressing the STATUS
button on the remote control, and the screen will
show :
SELBSTDIAGNOSE
1. Die Selbstdiagnose dient zum automatischen Prüfen
der Bus-Leitungen sowie des Hexadezimalcodes des
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :-
FS-Geräts. Zum Umschalten auf Selbstdiagnose
zunächst die Taste "STATUS" auf der
Fernbedienung und gleichzeitig die-Taste am
Bedienteil des FS-Gerätes drücken (-/v), auf dem
Bildschirm erscheint hierauf :-
2. Nach der Selbstdiagnose wird das Gerät automatisch
auf sämtliche werksseitigen Standardeinstellungen
zurückgesetzt :
zurückgesetzt :
Service-Hilfen
Zur Unterstützung der Servicearbeiten stehen weitere
Hilfsmittel zur Verfügung.
•
Hilfsmittel zur Verfügung.
•
LUCI
interface kit (PC-unterstützes Diagnosesystem)
Bestell-Nr.: TZS6EZ002
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
Es beinhaltet ein Interface, die Anschlusskabel zum FS-
Gerät und die Diagnose-Software. Bei Einführung von
neuen Modellen ist ein Update der Software jederzeit
möglich.
•
VICI
(Interaktive CD-ROM) mit schnellem Zugiff auf
Serviceinformationen.
Bestell-Nr.:
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
Bestell-Nr.:
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Bedienungsanleitungen
3. Technical Information
•
TASMIN
(Technisch erweitertes System für interaktive
Multimedia-Hinweise und Notizen)
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
Genauso wie dieses Produkt einen ersten Schritt in
Richtung erweitertes interaktives Training bereitstellt,
ermöglicht es einen noch schnelleren Zugang zu
technischen Informationen.
Service Aids
To aid in the service of our current chassis there are a number
of Service Aids which have been made available.
•
of Service Aids which have been made available.
•
LUCI
interface kit (Linked Utility Computer Interface)
Part number: TZS6EZ002
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
This contains interface and cables for connecting TV
service connector and a PC as well as diagnostic software.
As new models are introduced upgrade software will
become available.
•
VICI
(Visual Interactive Computer Information)
These C.D.'s contain multimedia documentation providing
quick access to service information.
Part No.
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
quick access to service information.
Part No.
TZS7EZ006, TZS7EZ005, TZS8EZ001 & TZS9EZ001
1. Service Manuals
2. Instruction Books
3. Technical Information
•
TASMIN
(Technically Advanced System for Multimedia
Interactive Notes)
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
As well as providing a first step towards more interactive
training this product also achieves quick access to
Technical Information.
If the CCU ports have been checked and found to be incorrect or not located then " - - " will appear in place of "O.K.".
Wenn der Hauptprozesser (CCU) an den Anschlüssen einen Fehler erkennt, oder der entsprechende Anschluss nicht belegt
ist, zeigt die entsprechende Position " - - " anstelle von OK an.
Wenn der Hauptprozesser (CCU) an den Anschlüssen einen Fehler erkennt, oder der entsprechende Anschluss nicht belegt
ist, zeigt die entsprechende Position " - - " anstelle von OK an.
VPC
O.K.
CIP
O.K.
SRC
O.K.
DDP
O.K.
TUN
O.K.
E2
O.K.
MSP
O.K.
DPL
- -
OPTION1
3D
[3D]
{3D}
OPTION2
1C
[1C]
{1C}
OPTION3
0D
[0D]
{0D}
OPTION4
00
[00]
{00}
OPTION5
EF
[CF]
{EF}
OPTION6
A1
[A1]
{A1}
PCB
O.K.
CAB
O.K.
6
ADJUSTMENT PROCEDURE
Item/Preparation
Adjustments
+B SET-UP
1. Receive a Greyscale signal.
2. Set
2. Set
the
controls:-
Brightness:
Minimum
Contrast:
Minimum
Volume:
Minimum
1. Confirm the following voltages.
B2
148 ± 2V
B10
5,25 ± 0,25V
B9
5
± 0,25V
B11
33
± 1,5V
B5
12
± 0,5V
B7
8
± 0,5V
B4
16
± 1V
B8
6
± 1V
B12
26
± 2V
B13
13,5 ± 1V
{28 ± 2V}
{16,5± 1V}
B3
36
± 1,5V
B14
-14 ± 1V
B1
205 ± 10V
{-10 ± 1V}
Cut-Off / Ug2 Test
1. Receive a Greyscale signal.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
2. Degauss the tube externally.
3. Set the TV into Service Mode 1.
4. Select Cutoff mode.
To adjust Cutoff connect an oscilloscope to the Blue
cathode.Press "STR" and adjust "cutoff" value using the
"Yellow" and "Blue" buttons until the black level is
160V ± 5V, press "STR" to store the value.
Remove the oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
cathode.Press "STR" and adjust "cutoff" value using the
"Yellow" and "Blue" buttons until the black level is
160V ± 5V, press "STR" to store the value.
Remove the oscilloscope.
Select Ug2 adjustment and adjust the screen VR until the
display shows "O.K."
ABGLEICH
Vorbereitungen
Abgleich
+B - Abgleich
1. Testbild
empfangen.
Helligkeit auf:
Minimum
Kontrast auf:
Minimum
Lautstärke:
Minimum
1. Folgende Spannungen sind zu überprüfen.
B2
148 ± 2V
B10
5,25 ± 0,25V
B9
5
± 0,25V
B11
33
± 1,5V
B5
12
± 0,5V
B7
8
± 0,5V
B4
16
± 1V
B8
6
± 1V
B12
26
± 2V
B13
13,5 ± 1V
{28 ± 2V}
{16,5± 1V}
B3
36
± 1,5V
B14
-14 ± 1V
B1
205 ± 10V
{-10 ± 1V}
Cut-Off / Ug2 Test
1. Testbild
empfangen.
2. Bildröhre
entmagnetisieren.
3. Service-Mode 1 anwählen.
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
4. Im Service-Mode den Abgleichpunkt Cutoff DC-Mode
wählen.
Einen Oszillographen an die blaue Katode der Bildröhre
anschliessen. STR-Taste drücken und Mit der gelben
und blauen Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste abspeichern. Den
Oszillograph entfernen und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf dem Bildschirm
erscheint. Den Wert abspeichern.
anschliessen. STR-Taste drücken und Mit der gelben
und blauen Taste den CUT-OFF Wert auf 160V ± 5V
abgleichen und mit der STR-Taste abspeichern. Den
Oszillograph entfernen und den Ug2 Test aufrufen. Den
Abgleichwert solange ändern, bis OK auf dem Bildschirm
erscheint. Den Wert abspeichern.
7
WAVEFORM PATTERN TABLE SIGNAL TABELLE
8
CONDITIONS:
CONTRAST...MAX, BRIGHTNESS...MID, COLOUR...MID, SHARPNESS...MID
Click on the first or last page to see other TX-28LK10C / TX-28LK10S / TX-28SK10C / TX-25LK10C service manuals if exist.